Speco OIPC22T7G User manual

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
1
OIPC22T7G
Owner’s Manual

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
2
Directions
Be careful not to cause any physical damage by dropping or throwing OIPC22T7G. Especially
keep the device out of reach from children.
Do not disassemble OIPC22T7G. No After Service is assumed when disassembled.
Use only the power adapter provided with OIPC22T7G.
Be careful to prevent moisture or water penetration into the unit. Particular attention is
needed when installing OIPC22T7G. The screw holes for the installation screws and pipe
should be maintained water tight during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from
the outside cannot flow into the unit through the surface of the wires. Penetration of the
moisture through the wire for extended period can cause malfunction of the unit or
deteriorated image.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
3
Revision History
Date
Revision
Details
2012-09-01
1.0
First manual revision creation.
Caution
Any changes or modifications in construction of this device which are not explicitly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
4
Contents
Contents............................................................................................................4
1. Introduction...................................................................................................6
1.1. Overview .................................................................................................................... 6
1.2. Specification............................................................................................................... 7
1.3. Applications of OIPC22T7G........................................................................................ 9
2. Product Description....................................................................................10
2.1. Contents................................................................................................................... 10
2.2. Product Preview....................................................................................................... 11
2.3. Physical description.................................................................................................. 12
2.4. Functional Description.............................................................................................. 12
3. On Site Installation .....................................................................................15
3.1. Ceiling or Wall Mounting........................................................................................... 15
3.2. Embedded mount bracket .............................................. Error! Bookmark not defined.
4. Getting Started............................................................................................17
4.1. PC Requirement....................................................................................................... 17
4.2. Quick Installation Guide............................................................................................ 18
5. Trouble Shooting .............................................. Error! Bookmark not defined.
5.1. No power is applied........................................................Error! Bookmark not defined.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
5
5.2. Cannot connect to the Video.......................................... Error! Bookmark not defined.
5.3. Windows Vista or Windows 7.........................................Error! Bookmark not defined.
5.4. Technical Assistance ...................................................... Error! Bookmark not defined.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
6
1. Introduction
1.1. Overview
The OIPC22T7G is a state-of-the-art, multi-codec (H.264, MJPEG) IP camera (or network camera) built with
embedded software and hardware technology. It enables real time transmission of synchronized video of up to
D1 and audio data. Remote clients can connect to OIPC22T7G for the real time video data through various
client solutions running on PC or mobile phones.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
7
1.2. Specification
Category
Sub-Category
Details
Video
Compression
H.264/MJPEG
Resolution
NTSC : 704x480, 640x480, 704x240,
352x240, 176x112
PAL : 704x576, 640x480, 704x288,
352x288, 176x144
Audio
(Bi-directional)
Up
N/A
Down
N/A
Network
Interface
RJ-45, 10/100 Mbps
Access network
Static, DHCP, PPP/PPPoE
Protocol
IPv4/6, TCP, UDP, IGMP, ICMP, ICMPv6 etc.
I/O
Sensor In
1
NC, NO Selectable
Relay Output
1
N/A
RS-232C
N/A
Mic/Line In
N/A
Line Out
N/A
CVBS output
N/A
Power Supply
PoE
N/A
DC Adaptor
12V DC adaptor (2A)
Mounting
Wall or Ceiling
Motion Detection
3 zones
Arbitrary shape with independent sensitivity
Upgrade
Firmware upgrade over IP network
Administration
Remote administration over IP network
Client & Viewer
Web Viewer
Simple viewing over internet explorer
Speco-NVR
Standard CMS software
3rd Party CMS
Ask SPECO for details
Dynamic IP support
DDNS support
Supported
Security
Video/Audio stream encryption
ID and Password protection

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
8
IP filtering for restricting administrative
access for audio and bi-audio
Time management
Sync to PC
Synchronize to PC
Manual
Manual time setting
Internet Time Server
Synchronize to Time Server
DLS
Day light saving
SDK support
Active-X
HTTP
Source filter

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
9
1.3. Applications of OIPC22T7G
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
10
2. Product Description
2.1. Contents
The product package contains followings :
Contents
Description
Remarks
OIPC22T7G
IP camera OIPC22T7G main unit
Power Adaptor
12VDC Adaptor
Optional item
CD
Software & User’s Guide
Quick Reference Guide
Quick installation guide

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
11
2.2. Product Preview
2.2.1. Preview
OIPC22T7G
IP-Installer
CMS Software
(Speco-NVR)
IP Camera
PC software to allocate an IP
address to the IP Camera
PC software to view and record
the A/V streaming data transmitted
from IP camera.
(Simultaneous support of up to 64
IP cameras)

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
12
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of OIPC22T7G
2.4. Functional Description
DC 12V : Power input for supplying 12V DC power.
Line Out
Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional
audio mode.
100Base-T
100Mbps Ethernet connector (RJ-45). 2 LEDs on the Ethernet connector shows the status of OIPC22T7G
as the followings:
-Status LED (Dual Color - Red/Green) : It will be lit in green or red depending on the status.
Green : Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is
connected to OIPC22T7G.
Red : Continuous or blinking red indicates that hardware is in abnormal condition.
Red/Green LED will be lit with red momentarily and it will be lit with green after a while when
power is applied into OIPC22T7G

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
13
- LINK/LAN LED (Orange)
It will be lit with orange color when network cabling is all right. Blinking orange color indicates that
normal data transmission is under way. Off state indicates that there is trouble in network connection.
ALARM IN/OUT and Composite Video Output
Figure 2-3 ALARM IN/OUT and Composite Video Output Terminal of OIPC22T7G
Used for connecting P/T device, sensor, and composite video output. Pin assignments are as follows.
Pin
Description
Misc.
1
SNS IN (+)
Sensor In (+). NC/NO selectable in admin mode.
2
SNS In (-)
Sensor In (-). NC/NO selectable in admin mode.
SNS IN : Examples of sensing devices are infrared sensors, motion sensors, heat/smoke sensors,
magnetic sensor, etc. Connect the two wires of the sensors to “SNS In”. The sensor type
(NC/NO) can be set in Administrative mode. 10mA can be flown into sensor device. Multiple
sensor devices can be connected in parallel.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
14
Sensor
Device
Sensor
Power
Supply
NO/ NCType
Sensor1-
Sensor1+
+12V GND
Sensor
Device
Sensor
Power
Supply
Open CollectorType
Photo Coupler
Figure 2-4. SENSOR Input connection
Factory Default Switch
A switch provided for returning the IP camera to factory default state. Open the cover to access the
switch. Press the switch for a few seconds while power is applied.
Figure 2-6 Factory Default switch of OIPC22T7G
Caution: Restoring the factory default will erase all settings.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
15
3. On Site Installation
3.1. C Ce ei il li in ng g o or r W Wa al ll l M Mo ou un nt ti in ng g
Please follow through the procedures in the order of the numbers for each procedure.
1. Open dome cover as following.
2. Fix the product using 3 screws and anchors

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
16
3. Combine dome cover.

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
17
4. Getting Started
Brief information for first time operation of OIPC22T7G is provided in this chapter.
4.1. PC Requirement
Video streaming data received from OIPC22T7G can be displayed or stored in a PC running client programs.
Minimum requirement of the PC is described below:
Recommended
Remark
CPU
Dual Core 3Ghz 3G above
Main Memory
2GB above
Operating System*
Windows XP
Web Browser
Internet Explorer 8.0 above
Graphic Card
256M above
Higher than 1600x1200
Network
100 Base-T Ethernet
* Operating Systems supported : Windows 2000 Professional / XP / Vista / 7

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
18
4.2. Quick Installation Guide
1. Connect PC and OIPC22T7G to network.
1) Prepare a PC to run programs for the installation and video connection
(PC is needed to assign IP address to OIPC22T7G)
2) OIPC22T7G as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor.
Figure 4-1. Power and network connection
Install “IP installer and set IP parameters on OIPC22T7G
Insert the CD provided with product into the PC. Install WinPcap and IP Installer in sequence. Make sure
that IP Installer can’t run without WinPcap.
IP installer Ver. 3.0.1 or later is needed in the configuration of OIPC22T7G.
Follow the sequence below for setting the IP parameter
i) Run IP installer > Select Network Adaptor >OK
ii) Click ①in IP installer window.> Double click on ②> Fill in ④> make a selection in ⑤> Fill the
parameters in ⑥
iii) Click on ⑨to apply the settings.
iv) You can connect to admin page by clicking on ⑩.
LAN switch
DC adaptor

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
19
2. Install Speco-NVR
Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC
to connect to these products. It is needed to assign connection information to Speco-NVR program before
connection.
Insert the CD provided with product into the PC and install the Speco-NVR.
Figure 4-2. Speco-NVR
Follow the sequence below for setting the IP parameter
v) Run IP installer
vi) Click ①in IP installer window.> Double click on ②> Fill in ④> make a selection in ⑤> Fill the
parameters in ⑥
vii) Click on ⑨to apply the settings.
viii) You can connect to admin page by clicking on ⑩.
Admin Page Button
IP installer

O
OI IP PC C2 22 2T T7 7G G O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.2 (Oct. 2012)
20
Click on the field in ③for sorting and rearranging the list.
Select network mode that best suits from the drop down list in ⑤. You can choose either
Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥
is deactivated.
In case of ADSL, fill the User Name and Password in ⑧with the values provided by your
ISP.
If DDNS service is needed, Check at the box and fill the empty field with hostname you want
in ⑦.
1
2
3
6
4
9
5
7
8
10