Speco O4P25X2 User manual

Quick Start Guide
O4P25X2

Welcome
Thank you for purchasing this PTZ camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 24VDC/AC Class 2 power supply or adequate PoE switch.
Please note: The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Do not expose the unit to heavy stress, violent vibration or long-term exposure to water
and humidity during transportation, storage, and/or installation.
Do not install near sources of heat.
Only install the product in environments inside the specification operating temperature
and humidity range.
Do not install the camera near power lines, radar equipment or other electromagnetic
radiation.
Do not block any ventilation openings if any.
Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning

Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.

Overview
3 Overview
1
① Ethernet Connector (PoE++)
② 3.5mm Audio Out
③ 3.5mm MIC In
④ Alarm In/Alarm Out
⑤ 24VDC/AC Power Input Jack*
Ground
1
2
3
4
5
*24VDC Power adapter included
Installation
2
◆ Install SD Card
Please make sure the wall is strong enough to bear the dome
camera’s weight. Please make sure the camera is powered off
during installation.
1
2
3
4
5
6
ALARM
4 3 2 1
6

① Loosen the two screws of the dome. ② Open the cover and insert SD card.
Insert SD card
◆ Install the Speed Dome
② Drill the screw holes on the wall
according to the drill template. Then
insert the screw anchors into the holes.
③Attach the bracket to the wall
with four screws.
① Fasten the adpater to the bracket.
Adapter
④ Hook the safety wire to the bracket.
Then connect the cables. After that,
secure the speed dome to the bracket
with the screws .
8.0mm
78.5mm
100.0mm

Cable Connection
3
HP Audio Out
Ethernet Port
MIC IN
Power
ALM-OPEN
ALM-COM
ALM-GND
ALM-IN1
24V A
24V B
Earth
DC24V
AC24V
Alarm Connection:
1. Alarm Input
a) There is one independent alarm input port (ALM-IN1) and
one grounding port (ALM-GND).
b)Alarm input(NO type): Connect DC5V~DC12V voltage
between the alarm input port( ALM-IN1) and the grounding port
(ALM-GND).
c) Alarm input(NC type): Disconnect the voltage between the
alarm input port(ALM-IN1) and the grounding port (ALM-GND).
ALARM
4 3 2 1
Connect to earth ground

2. Alarm Output
a) Support 1CH alarm output including OPEN, COM
connections.
b) Alarm output: One passive switch for user to connect alarm
devices; the alarm output state will be auto on/off according to
your setting.
Web Operation and Login
4
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.
5C :F2:0 7: 24:68 :B9
O4 P25X2
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.

The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.