Speco ONSIP 02S1 User manual

ONSIP 02S1

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Nov., 2011)
Note
This equipment has been tested and found to comply with the limits for a Class a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications . However, there is no guarantee that interference
will not occur in a particular installation . If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna .
 Increase the separation between the equipment and receiver .
 Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected
 Consult the dealer or an experienced radio/TV technician for help .
2

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Revision History
Rev.1.0 (Nov., 2011)
Date
Revision
Details
2011-11-01
1.0
First manual revision creation .
Caution
Any changes or modifications to this device could void the warranty.
Directions
▪Be careful not to cause any physical damage by dropping or throwing ONSIP O2S1.
▪Especially keep the device out of reach from children.
▪Do not disassemble ONSIP O2S1. No After Service is assumed when disassembled .
▪Use only the power adapter provided with ONSIP O2S1.
▪Be careful to prevent moisture or water penetration into the unit. Particular attention is needed wh
en installing ONSIP O2S1. The screw holes for the installation screws and pipe should be maintaine
d water tight during the whole life time of the product.
▪All the electrical connection wires running into the unit should be prepared so that water from the
outside cannot flow into the unit through the surface of the wires. Penetration of the moisture throu
gh the wire for extended period can cause malfunction of the unit or deteriorated image.
3

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Contents
Contents.......................................................................................................... 4
1 .Introduction ............................................................................................... 6
1.1 . Overview ................................................................................................................. 6
1.2 . Specification ........................................................................................................... 7
1.3 . Applications of ONSIP O2S1................................................................................ 8
2 .Product Description .................................................................................. 9
2.1 . Contents.................................................................................................................. 9
2.2 . Product Preview ................................................................................................... 10
2.3 . Physical description............................................................................................. 11
2.4 . Functional Description ........................................................................................ 13
2.5 . Sensor-IN and Relay-OUT.................................................................................. 15
3 .Getting Started........................................................................................ 18
3.1 . PC Requirement ................................................................................................... 18
3.2 . Quick Installation Guide..................................................................................... 19
4 . Trouble Shooting ..................................................................................... 25
4.1 . Video movement is slow. ................................................................................... 25
Rev.1.0 (Nov., 2011)
4

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
4.2 . The image is dull and I see green, pink dots. ............................................... 25
4.3 . Mosaic phenomenon. .......................................................................................... 25
4.4 . Cannot connect to the Video............................................................................. 25
4.5 . Windows Vista or Windows 7 ............................................................................ 26
4.6 . Technical Assistance ........................................................................................... 29
Rev.1.0 (Nov., 2011)
5

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
1. Introduction
1.1 . Overview
The ONSIP O2S1 is a state-of-the-art Megapixel, multi-codec (H.264, MJPEG) Day/Night IP camera built with
embedded software and hardware technology . It enables real time transmission of synchronized video of up to 2
Megapixels and audio data. Remote clients can connect to ONSIP O2S1 for the real time video/audio data
through various client solutions running on PC, Smart Phones (iPhone/Android) . Real time 2-way
communication is available through bidirectional audio communication feature.
Designed to be a stand-alone streaming audio & video transmission device, ONSIP O2S1 can be applied to
various application area such as video security, remote video monitoring, distance education, video conference
or internet broadcasting system.
Use the optional integrated backup battery to insure connection continuity when local power is unreliable.
Additional options are, IR illumination, and integrated Pan/Tilt motor.
Based on Speco Technology’s Embedded Software Solution (Embedded Web Server, Embedded Streaming
Server & Network Protocol), the ONSIP O2S1 delivers unprecedented performance and stability. Weather
your application is basic, or scaling to the enterprise, Speco Technology Network Video Recording Applications
(NVR PRO) offer highly reliable methods of managing your security video.
Additional options are:
Integrated Battery backup
(Provides valuable standby power in the event of a power failure)
Integrated IR Illumination for super reliable “Day/Night” Video
Integrated Motorized Pan/Tilt
(Allowing for remote Pan /Tilt camera movement)
Rev.1.0 (Nov., 2011)
6

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Details
H.264/MJPEG
**Refer to the datasheet.
32 Kbps G.726
64 Kbps PCM
100BaseT, IEEE 802.11b/g/n
Static, DHCP, PPP/PPPoE
RTP, RTSP, SMTP, FTP, HTTP, SDP,
NTP, DNS, HTTPS
1 NC, NO Selectable
For alarm annunciation or
1
remote ON/OFF control (30V, 1A)
For factory use only
Proprietary Power over Ethernet
Wall Mount Bracket
Arbitrary shape with independent sensitivity
Firmware upgrade over IP network
Remote administration over IP network
Simple viewing over Internet Explorer
Standard CMS software
Supported
ID and Password protection
IP filtering for restricting administrative access for audio and bi-audio
Sync to PC Synchronize to PC
Manual Manual time setting
Internet Time Server Synchronize to Time Server
DLS Day Light Saving
Active-X
HTTP
Rev.1.0 (Nov., 2011)
1.2 . Specification
Category
Video
Audio
(Bi-directional)
Network
I/O
Power Supply
Mounting
Motion Detection
Upgrade
Administration
Client & Viewer
Dynamic IP support
Security
Time management
SDK support
Sub-Category
Compression
Resolution
Up
Down
Interface
Access network
Application
Sensor In
Relay Output
RS-232C
3 zones
Web Viewer
Speco-NVR
DDNS support
7

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
1.3 . Applications of ONSIP O2S1
 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference).
Real time Internet broadcasting
Distance (Remote) Learning/Education




















































Rev.1.0 (Nov., 2011)
8

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
2. Product Description
2.1 . Contents
The product package contains followings:
Description Shape Remarks
ONSIP O2S1 IP Camera
Back Box for housing adaptors
Power adaptor with proprietary
PoE.
Installed inside the Back box for
connecting AC power to the power
supply.
Back box cover.
Mounting bracket for installing the
main body on the wall or
connecting the power adaptor box
with the main body.
Corner Mount Adapter
Li-ion battery pack
Battery compartment cover.
Rev.1.0 (Nov., 2011)
Contents
Main Body
Adaptor Box
Power Adaptor
AC connector PBA
Adaptor box cover
Mounting bracket
Corner Mount Bracket
Battery
Battery cover
9

AC cable
Short Network LAN cable for
Ethernet and PoE applications
Screws (33 pieces or 7 types) and
washers (15 pieces of 3 types)
Terminal block for connecting one
sensor input and one relay output.
Software & User’s Guide
IP-Installer
PC software to allocate an IP
address to the IP Camera
Rev.1.0 (Nov., 2011)
CMS Software
(Speco-NVR)
PC software to view and record
the A/V streaming data transmitted
from IP camera.
(Simultaneous support of up to 64
IP cameras)
10
O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
AC cable
LAN cable
Screws and mounting
fixtures
Terminal block
CD & Documents
2.2 . Product Preview
ONSIP O2S1
Mega pixel IP Camera

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
2.3 . Physical description
2.3.1. Exterior View
Figure 2-1. Exterior view of ONSIP O2S1
 Status LED: Integrated microphone
Status LED: Green color indicates that the camera is in normal operation mode, while RED color
indicates that the camera is in abnormal condition.
 MICROPHONE: Integrated microphone
 Speaker: Integrated speaker






Rev.1.0 (Nov., 2011)
11

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
 Factory Default Reset: Used for returning the network camera to the factory default state. One must
open the cover in order to access the switch . To reset: Power down the camera, next while powering up
the camera, hold down the reset switch for three seconds.
2.3.2 . Power Adaptor and Accessories
Figure 2-2. PoE power adaptor, accessories and installation
Rev.1.0 (Nov., 2011)
12

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
2.4 . Functional Description
 100Base-T
100Mbps Ethernet connector (RJ-45) with proprietary PoE . 2 LEDs on the Ethernet connector shows the
status of ONSIP O2S1 as the followings:
- Status LED (Dual Color) : It will be lit in green or red depending on the status.
 Green: Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is
connected to ONSIP O2S1.
 Red: Continuous or blinking red indicates that hardware is in abnormal condition. 
- LINK/LAN LED (Orange)
It will be lit with orange color when network cabling is all right. Blinking orange color indicates that
normal data transmission is under way. Off state indicates that there is trouble in network connection.
Red/Green LED will be lit with red momentarily and it will be lit with green after a while when
power is applied into ONSIP O2S1
 RS-232C
RS232C interface is provided through mini-USB type connector . The pin assignments are shown in the
following table . RS-232C is reserved for factory usage only.

Sensor In/Relay Out: used for connecting input sensors, and alarm devices to ONSIP O2S1











 Sensor Input: Connect external alarm sensors such as the infrared






Rev.1.0 (Nov., 2011)
Pin
Description
Misc.
3
TxD of RS-232C
For debugging & factory use only .
4
RxD of RS-232C
For debugging & factory use only .
5
Ground of RS-232C
For debugging & factory use only .
Pin
Description
Misc .
1
Sensor In (+)
NC/NO selectable in admin mode.
2
Sensor In (-)
NC/NO selectable in admin mode.
3
Relay out
Normal close
4
Relay out
Common
sensors, heat
13

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
sensors, magnetic contacts, etc . (NC/NO selectable on the admin page.)
 Relay Output: It is used for connecting external alarm generators such as sirens,
flashing light, etc. When activated, relay output configures a closed circuit.
Rev.1.0 (Nov., 2011)
14

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
2
2. .5 5
.
.
S
Se en ns so or r- -I IN N a an nd d R Re el la ay y- -O OU UT T
Sensor-In and Relay-Out cable is used to connect various sensing and alerting devices. Examples of se
nsing devices are infrared sensors, motion sensors, heat/smoke sensors, magnetic sensor, etc. Relay-Ou
t t is used for connecting alerting device such as loud speaker, flashing light, etc.
1.
Sensor-IN
Connect the two wires of the sensors. The sensor type can be set in Administrative
Mode(Ref . 5.6) . Output lines providing on-off switching are connected between
“+“ and “-”pins. Figure 6-1 shows the input circuit of “Alarm In”.
Figure 2-5. SENSOR input
Rev.1.0 (Nov., 2011)
15

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
2.
Relay-OUT
A Relay output is provided for connecting alarm devices or for remote on/off devices such as light
control . Relay circuits are normal open and circuits are closed upon alarm output or remote on . The
relay is capable of switching AC/DC 30V, 1A electrical signal.
Figure 2-6.
RELAY Output
3.
Connection of Sensor, Alarm Device
3.1 Connection of Sensor
NO/ NCType Op en Co llec to rTyp e
Senso r1+
Senso r Sensor
Sen so r1-
Sup p ly Sup p ly
Figure 2-7.
Sensor Connection
Rev.1.0 (Nov., 2011)
Photo Coupler
+ 12V
Devic e
Sen so r
Po wer
GND
Po wer
Devic e
Senso r
16

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
3.2 Connection of Relay
Relay Switch Power Supply
Out
Supply( 30V
~)
Relay Switc h
Alarm
Relay1
use the supported relay output to directly drive
AC/DC at 1A . By connecting additionally relay circuitry (such as optional relay switch),
it can also drive heavier loads.
Figure 2-8.
Relay Connection
Rev.1.0 (Nov., 2011)
Alarm
Devic e
Po wer
1V~ 30VDC/ AC,1A
Relay1
-
+
Relay
You can
Optional
Devic e
Po wer
Sup p ly(1~30
VDC/AC,1A )
a maximum load of 30V
Out
17

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
3. Getting Started
Brief information for first time operation of ONSIP O2S1 is provided in this chapter.
3.1 . PC Requirement
Audio/Video streaming data received from ONSIP O2S1 can be displayed or stored in a PC running client
programs . Minimum requirement of the PC is described below:
Recommended Remark
CPU Dual Core 3G above
Main Memory 2GB above
Operating System
*
Windows XP
Web Browser Internet Explorer 6.0 above
Graphic Card RAM 128MB above Higher than 1600x1200
Network 100 Base-T Ethernet
Rev.1.0 (Nov., 2011)
18

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
3.2 . Quick Installation Guide
1.
Install the battery in the battery compartment and place the battery cover lid.
2. Assemble the power adaptor box as required for your installation condition.
3. Connect ONSIP O2S1 to LAN by using one of the following methods
If you have PoE power adaptor, connect the network camera and PC as illustrated in Figure 2.3. both
power and network connection are made with a single LAN cable.
Figure 3-1. PoE power adaptor, accessories and installation
Rev.1.0 (Nov., 2011)
19

O
O2 2S S1 1 O Ow wn ne er r’ ’s s M Ma an nu ua al l
4.
Install Speco-NVR
Speco-NVR is a multi-channel CMS program for to IP camera or Video server . Install Speco-NVR on remote PC
to connect to these products. It is needed to assign connection information to Speco-NVR program before
connection.
Insert the CD provided with product into the PC and install the Speco-NVR.
Admin Page Button
IP installer
Figure . 3-2 . Speco-NVR
Follow the sequence below for setting the IP parameter
i) Run IP installer
ii) Click ①in IP installer window.> Double click on ②> Fill in ④> make a selection in ⑤> Fill the
parameters in ⑥
iii) Click on ⑨ to apply the settings.
iv) You can connect to admin page by clicking on ⑩.
Rev.1.0 (Nov., 2011)
20