Speco V5B2 User manual

USER MANUAL
Thank you for purchasing our product. Speco Technologies is constantly developing and
improving products. We reserve the right to modify product design and specifications
without notice and without incurring any obligation.
V5B2/V5T2/V5D2/V5B2M/V5D2M/V5T2M

Warnings
■ If the product does not work properly, please contact the dealer or where the product was purchased.
Speco Technologies is not responsible for any problems caused by improper operation or repair.
■ Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity
during transportation, storage, and/or installation.
■ Do not install near sources of heat.
■ Only install the product in environments inside the specification operating temperature and humidity
range.
■ Do not install the camera near power lines, radar equipment or other electromagnetic radiation.
■ Do not block any ventilation openings if any.
■ Use all the weatherproofing hardware requirement to minimize weather intrusion.
This camera series is the latest technology and advanced circuit design, which features high definition and
sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,
ensuring the requirement of the HD monitoring in the traditional surveillance system.
Introduction
● High Resolution
Adopt high performance sensor, providing high definition and clear image.
● High Transmission Performance
Real-time transmission with high speed and long distance.
● DNR
Reduce noise from brightness and color signal.
● OSD
Access the camera settings which can be clearly displayed through the main menu.
● White Balance
Adjust the color temperature according to the environment automatically.
● ICR Auto Switch
The filter will filter infrared light during the daytime and change to normal at night to
ensure a high sensitivity and clear image.
● AGC
Adjust the gain of amplifier, enabling the camera to output the standard video signal in different
lighting condition.
● Wide Dynamic Range (WDR)
When there are both very bright and very dark areas simultaneously in the field of view, this function
will balance the brightness level and provide clear images.
● Backlight Compensation (BLC)
When the back of the captured object is too much bright, you can set BLC for the captured object to
make it clearer. 1

Cables
Power Cable
Video Output
Video Switch Cable
Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS
(a) remove the cover of the video switch cable; (b) hold and press the button in the video
switch cable for 5 seconds to switch the current video output.
2
Before you start, please make sure that the wall or ceiling is strong enough to withs tand three times
the w eight of the camera. Please install and use the camera in the dry environment.
You’d better install back the lens cover or lower dome less than 4 hours after removing it.
The mounting types of cameras are only for reference.
Installation
►Mounting for V5B2/V5B2M►Mounting for V5B2/V5B2M
1. Drill the screw holes and the cable hole on the wall according to the drill template. 1. Drill the screw holes and the cable hole on the wall according to the drill template.
2. Route and connect the cables .
3. Secure the mounting base with camera to the wall with screws as shown below.
2. Route and connect the cables .
3. Secure the mounting base with camera to the wall with screws as shown below.
∅4.6
∅25.1
∅82.0
∅72.2
120°
120°
62.5mm
18.1mm
36.1mm
∅4.6
∅25.1
∅82.0
∅72.2
120°
120°
62.5mm
18.1mm
36.1mm

4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the
fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.
3
►Mounting for Dome Camera
1.Attach the drill template to the place where you want to fix the camera and then drill the screw holes
and the cable hole on the wall according to the drill template.
● Mounting for V5D2/V5D2M
V5B2M
V5B2M
V5B2
V5B2
74.3
74.3
(mm)
∅4.6
90.2mm
90.2mm
V5D2 V5D2M
Fixed Ring
Pan 360°
Tilt 80°
PA 4×25mm
PA 4×25mm
3× 3×
Fixed Ring
Pan 360°
Tilt 90°

2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove
the trim ring from the gap of the camera.
Rubber plug
Lower dome
* Install it when routing the
cables through the ceiling.
3. Loosen the screws to open the lower dome. Then route and connect the cables.
4. Secure the camera to the wall with screws provided as shown below.
V5D2 V5D2M
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then
adjust the camera according to the figure below to get an optimum angle.
Rotation 0°~355°
Pan 0°~355°
Tilt 0°~67°
Turn
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower
dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.
Trim ring

Gap
Microphone
4

● Mounting for V5T2/V5T2M
1. Drill the screw holes and the cable hole on the wall according to the drill template .
2. Loosen the fixed screw to disassemble the camera.
3. Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
4. Install the camera unit and enclosure to the mounting base and then adjust the dome to obtain an optimum
view angle. Finally, secure the camera with the fixed screw.
Tilt: 0˚~75˚
Tilt: 0˚~80˚
Rotate: 0˚~360˚
Pan: 0˚~360˚
V5T2M
V5T2
V5T2:
V5T2M:
∅4.4mm
∅107mm
∅118.5mm 120° 120°
Fixed Screw
Mounting Base
Enclosure
Camera Unit
③ Route and connect the cables. Then secure the mounting base to the
ceiling or wall with the screws provided.
PA 4×25mm
3×
④ Install the camera unit and enclosure to the mounting base and then
adjust if necessary to obtain an optimum view angle. Finally, fasten the
camera with the fixed screw.
5
∅130.7mm
∅119.5mm
∅4.5mm
120°
120°

6
Specifications
Camera
Image Sensor
Resolution
Image size
Video Output
Image System
Electronic Shutter
IR Distance (feet)
Frame Rate
Min. Illumination
Lens
Lens Mount
S/N Ratio
Ingress Protection
Functions
Function Control
Day &Night
DWDR
Digital NR
AGC
Auto White Balance
Defog
BLC
LSC
Mirror
Sharpness
Smart IR
Image Setting
Defect Correction
Others
Power Supply
1/2.7" CMOS
5MP
2560×1936
AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)
PAL/NTSC
Auto; 1/50s~1/100000s(PAL);1/60s~1/100000s (NTSC)
65.6~98.4
20fps
Color:0.01lux@F1.2, AGC ON; B/W: 0lux with IR
M12 D14 M12
≥ 52dB(AGC OFF)
IP67
OSD (UTC control)
ICR
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Auto
DC12V (± 10%)
IR OFF: < 1W;
Specifications
Models V5B2 V5B2M
8.6 3.39 3.386× ×
6.74 3.27 3.26× ×
2.8~12mm (motorized)
IP67
IR OFF: < 1W; IR OFF: < 1W;
98.4~164.0
IP67&IK10
Power Consumption
Dimensions (inch)
Working Environment
IR ON : < 4W
-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)
IR ON : < 6W IR ON : < 4W
65.6~98.4
V5D2
Ф4.72 3.45×
2.8mm 2.8mm

Camera
Image Sensor
Resolution
Image size
Video Output
Image System
Electronic Shutter
IR Distance (feet)
Frame Rate
Min. Illumination
Lens
Lens Mount
S/N Ratio
Ingress Protection
Functions
Function Control
Day &Night
DWDR
Digital NR
AGC
Auto White Balance
Defog
BLC
LSC
Mirror
Sharpness
Smart IR
Image Setting
Defect Correction
Others
Power Supply
1/2.7" CMOS
5MP
2560×1936
AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)
PAL/NTSC
Auto; 1/50s~1/100000s(PAL);1/60s~1/100000s (NTSC)
98.4~164.0
20fps
Color:0.01lux@F1.2, AGC ON; B/W: 0lux with IR
D14 M12 D14
≥ 52dB(AGC OFF)
IP67&IK10
OSD (UTC control)
ICR
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Auto
DC12V (± 10%)
IR OFF: < 1W;
Specifications
Models V5D2M V5T2
Ф4.67 3.69×
Ф5.61 3.95×
2.8~12mm (motorized)
IP67
IR OFF: < 1W; IR OFF: < 1W;
65.6~98.4
IP67
Power Consumption
Dimensions (inch)
Working Environment
IR ON : < 6W
-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)
IR ON : < 4W IR ON : < 6W
98.4~164.0
V5T2M
Ф4.21 5.16×
2.8mm 2.8~12mm (motorized)
7

Model: V5B2/V5B2M/V5D2/V5D2M/V5T2/V5T2M
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
FCC Responsible Party:
Speco Technologies
200 New Highway
Amityville, NY 11701
www.specotech.com