Speco CDD11HW User manual

S250
INSTRUCTION
MANUAL CDD11HW
960H Diamond Indoor Dome Camera

1
Content
Content
Warning & Caution
General Features
Composition
Dimension
Connection
Product Overview
Installation
Specification
OSD Menu
OSD Menu Setting
Trouble Shooting
1
2
3
4
5
6
7
8
11
12
13
14

2
This symbol is intended to alert the user to the presence
of un-insulated“dangerous voltage”within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature accompanying
the appliance persons.
Warning & Caution

3
General Features
• Resolution : 700 TV Lines
• Built in Fixed Lens 3.6 mm
• Min.illumination :
Color : 0.1Lux, B/W : 0.01Lux
• Tact Switch type OSD Control
• Motion Detection, Privacy Zone, Mirror Function
• 2nd Video-out connector for installer
• Dynamic 3-Axis Movement for Free Lens Rotation
• Power DC 12V
• DNR : 2D
• DWDR: Digital Wide Dynamic Range
18 AWG 200 m
Wire Gauge DC12V
Power Wire Maximum Distance

4
Composition
1. Camera
2. Mounting Screws
Tapping Screws 4 x 25
3 pcs
3. Instruction Manual
4.
Pig Tail

5
Dimension
2.5”
2.4”
3.4”
1.2” 1.3”
Units : inch

6
Connection
1. DC Jack
2. Power Adaptor (DC 12V)
3. BNC Jack (Video Output)
3
12
Monitor

7
Product Overview
6
1
2
3
4
Up
Down
Left Right
1. Dome Glass 2.4”
2. Top Cover
3. Main Body
4. Bottom Cover
5. Lens
6. OSD Menu Switch
5

8
Installation
Refer all work related to the installation of this product
to qualified service personnel or system installer.
1. Remove the Top Cover
a. Gently turn the Top Cover
counter-clockwise to unlock,
then pull free of the Main Body.
b. Set the dome and Main Body
aside.
2. Connect the Wiring
a. Video output connector.
b. Power connector.
Preparation

9
Installation
- The dome camera has three position adjustments ,
and OSD Menu Setting Switch.
A = Pan rotation
B = Horizontal rotation
C = Tilt rotation
A
B
C
a. Pass the Power Cable and the
Video Cable from the camera
unit through the hole in the
ceiling.
b. Install the Main Body to the
desired installation surface
using 3 supplied mounting
screws.
Camera Mounting
Camera Adjustment
*
If necessary, loosen the screw that locks the gimbal
assembly in place, before adjusting the camera.

10
Installation
- OSD Menu Setting is controlled by Tact Switch
type OSD Menu Switch located in backside of
control PCB.
- After installation and adjustment of the camera
is complete, secure the Top Cover by turning it
clockwise.
OSD Menu Switch
Up
Down
Left Right

11
Specification
1/3” Sony Supper HAD II CCD (960H)
NTSC TV System
1028(H) x 508(V)
976(H) x 494(V)
15.734kHz x 59.94Hz
2:1 Interlace
Internal Synce
1/60s ~ 1/100,000s
Max. 700 TVL
50 dB or more (AGC o)
Color : 0.1 lux, B/W : 0.01 Lux
VBS 1.0V p-p/75 Ω
r = 0.45
Fixed 3.6mm
OFF / LOW / MIDDLE / HIGH Selectable
2D-DNR: ON / OFF
ON / OFF (4 Zone ISO Control / Output OSD)
ON / OFF (8 areas)
DWDR
AUTO / MANUAL / OFF
Level Adjustable
ATW / MANUAL / AWC
DC12V / 150mA / 1.8W
Regulated DC12V 200mA Power Supply
OSD
-4° ~ 140F , RH 95% Max
3.4” x 2.5” (Glass Ø 2.4”)
Approx. 0.24lbs
IImage Sensor
Video System
Total Pixels
Effective Pixels
Scanning Frequency
Scanning System
Sync System
Shutter Speed
Resolution
S/N Ratio
Min. Illumination
Video Output
Gamma
Lens
Auto Gain Control
DNR
Motion Detection
Privacy Masking
WDR
DPC
Sharpness
White Balance
Power
Recommended Power
Outside Control
Operating Temps.
Dimensions
Weight
Type CDD11HW

12
OSD Menu
LENS
HBLC/D-WDR
AGC
2D-DNR
RETURN
WB MODE
R-Y GAIN
B-Y GAIN
RETURN
D&N MODE
C_SUP
A_SUP
RETURN
MIRROR
SHARPNESS
LSC
RETURN
MOTION
AREA
SENSITIVITY
DISPLAY
HOLD TIME
ALARM
RETURN
ELC, DC
OFF
BLC - MODE, WEIGHT
OFF,LOW,MID,HIGH
ATW, MANUAL, PUSH
AUTO, COLOR, B&W, EXT
<0 ~ 100>
<0 ~ 100>
OFF, MIRROR
<0~30>
OFF, ON <0 ~ 30>
OFF, ON
AREA1 ~ AREA4
<1 ~ 30>
OFF, ICON, TRACE
<0~15>
OFF, ON
EXPOSURE
COLOR (W B)
DAY&NIGHT
FUNCTION
MOTION

13
OSD Menu
MASK1
MASK8
RETURN
TITLE
DPC
OLPF
MONITOR
GAMMA
RETURN
CAMERA ID
COMMUNI.
LANGUAGE
OSD COLOR
RETURN
FACTORY
SAVE & EXIT
EXIT
OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET
OFF
ON
DOT SEL
DOT XY
MOVE XY
COLOR SET
AUTO/MANUAL
FILTER 1
CRT
0.45
OFF
BLUE
NO
PRIVACY
SET UP
SYSTEM
EXIT
* Depending on the setting of sub menu, the default
value may be changed.

14
OSD Menu Setting
LENS ELC
AGC HIGH
HBLC/D-WDR OFF
2D DNR ON
RETURN RET
E. SHUTTER AUTO
RETURN
BRIGHT 050
LENS – ELC
E. SHUTTER AUTO
RETURN
BRIGHT 050
LENS – ELC
The Lens, HBLC/D-WDR, AGC, etc options that are available
in the EXPOSURE menu.
EXPOSURE
- Select ELC mode for electronic
shutter AE controls.
- Select DC mode for DC-IRIS
controls.
- E.SHUTTER – setting value of
electronic shutter.
- Select mode : Auto,1/60(1/50),
1/100, 1/120FLK, 1/250, 1/500,
1/1000, 1/2000, 1/4000, 1/10000,
1/100000 sec. (default : AUTO)
- When selecting in Auto mode(default) : The shutter mode from
1/60 to 1/100000 is controlled automatically.
- BRIGHT : For target brightness
control.
- AE controls this in compliance
with a set bright control. Bright
control from 1 to 100, the defult
is 50.
EXPOSURE – LENS – ELC – E.SHTTER
EXPOSURE – LENS – ELC – BRIGHT
EXPOSURE – LENS
EXPOSURE

15
LENS ELC
AGC HIGH
HBLC/D-WDR OFF
2D DNR ON
RETURN
E. SHUTTER 1 / 60
RETURN
BRIGHT 050
LENS – DC
E. SHUTTER 1 / 60
RETURN
BRIGHT 050
LENS – DC
E. SHUTTER 1 / 60
RETURN
BRIGHT 050
LENS – DC
- LENS – DC mode setting.
- E.SHUTTER : Electronic shutter
value setting mode in DC IRIS.
- 1/60(1/50), 1/100, 1/120FLK, 1/250,
1/500,1/1000,1/2000,1/4000,1/10000,
1/100000 sec.
- BRIGHT : Setting for target
brightness.
- Controls brightness value of DC
IRIS. Bright control from 1 to
100, the defult is 50.
- DC modes use DC-IRIS lenses and they control AE.
Electronic shutter speed default is 1/60.
- Control value from 0 to 20, the
defult is 10.
- Select menu for BLC / HLI /
D-WDR
- BLC mode : Back Light
Compensation.
- HLI mode : High Light Inverse.
- D-WDR mode : Digital Wide
Dynamic Range.
EXPOSURE – LENS – DC – E.SHTTER
EXPOSURE – LENS – DC – BRIGHTNESS
EXPOSURE – LENS – DC
EXPOSURE – LENS – DC REF
EXPOSURE – HBLC/D-WDR
EXPOSURE
DC REF 000
DC REF 000
DC REF 000

16
LENS ELC
AGC HIGH
HBLC/D-WDR BLC
2D DNR ON
EXIT RET
-Selected BLC mode.
EXPOSURE – HBLC/D-WDR – BLC
EXPOSURE
BLC MODE MANUAL
RETURN
BLC WEIGHT MID
BLC - Select AUTO or MANUAL.
- Sets the total AE level at AE
value of select window area.
- AUTO, selects the darkest area
with automatic and photometry
weight.
EXPOSURE – HBLC/D-WDR – BLC –BLC MODE
LENS ELC
AGC HIGH
HBLC/D-WDR HLI
2D DNR ON
EXIT RET
- HLI mode : High Light Inverse.
- It is a function which reverses
the area with strong light.
- The HLI BLC mode control by
BLC window area. (HBLC)
- Use mode set of HLI
(ALL DAY / NIGHT).
- ALL DAY : Always operating HLI
- NIGHT : Operating only in NIGHT
environment, HLI does not operate in DAY conditions.
- You can select 4 mask areas in DAY&NIGHT and adjust HLI level.
EXPOSURE – HBLC/D-WDR – HLI
EXPOSURE

17
- D-WDR captures the images at all light levels by correcting
GAMMA CURVE.
- If you use an ordinary camera in a scene with an intensive
backlight, the object will be displayed dark on the monitor .To
solve this problem, you can use the
D-WDR function is to improve the dark parts without saturation
from bright part.You can adjust SET LEVEL to get clearer images.
EXPOSURE – HBLC/D-WDR – D-WDR
LENS ELC
AGC HIGH
HBLC/D-WDR BLC
2D DNR ON
SENSE-UP AUTO
RETURN
- AGC : Auto Gain Control level set
OFF / LOW / MIDDLE / HIGH.
EXPOSURE – AGC
EXPOSURE
COLOR (WB)
WB MODE ATW
B - Y GAIN 128
R - Y GAIN 128
RETURN
- White Balance control mode selects.
ATW / MANUAL / AWC>PUSH
- Selection of COLOR – WB MODE - ATW
- ATW : Auto Tracking White
Balance mode
- User can change color.
The white balance mode and color gain setting menu.
COLOR – WB MODE
COLOR
WB MODE AWC
B - Y GAIN 128
R - Y GAIN 128
EXIT RET
- The color gain controls R-Y
COLOR – R-Y GAIN
COLOR

18
- The color gain controls B-Y
COLOR – B-Y GAIN
D&N MODE COLOR
A - SUP 030
C - SUP 030
RETURN
- D&N change mode sets.
- Select of AUTO / COLOR / B&W /
EXT.
- AUTO mode: D&N is decided by AGC gain
level.(without LED)
- COLOR mode: Only Color mode
operates.
- B&W mode: Only B&W mode operates.
- EXT mode: D&N decision by external CDS signal. (with LED)
- Color & B/W change, D&N lter change, Color/Aperture level
control.
DAY&NIGHT – D&N MODE
DAY&NIGHT
DAY&NIGHT
-The color noise suppress in NIGHT mode.
- The aperture level suppress in NIGHT mode.
DAY&NIGHT – C_SUB
DAY&NIGHT – A_SUB
MIRROR OFF
LSC OFF
SHARPNESS 020
RETURN
- MIRROR : Image mirroring
ON/OFF mode.
- SHARPNESS: Sharpness level
control ( 0 ~ 30, 1 step)
- LSC: Lens Shading Compensation
ON/OFF mode
FUNCTION
DAY&NIGHT
FUNCTION
- Sets for MIRROR, Sharpness, LSC mode

19
MOTION OFF
AREA SEL AREA1
SENSITI. 025
ALARM OFF
- MOTION : Select operates
ON/OFF
- AREA SEL : Select each area
- SENSITI. : Control MOTION
sensitivity. (0 ~ 30, 1 step)
- DISPLAY: Control alarm mode
when MOTION indicates.
( Select of OFF / ICON / TRACE)
MOTION
MOTION
MOTION
- This function informs the user there is motion on the screen.
Up to 4 area zones.
DISPLAY TRACE
HOLD TIME 003
RETURN
MASK 1 ON
MASK 6 OFF
- The each mask selects ON/OFF
- After selecting each mask, it can
select color, location, area of mask.
PRIVACY – MASK1 ~ MASK 8
PRIVACY
PRIVACY
- The mask controls are for the zones where privacy is necessary.
There are total of 8 mask zones.
MASK 4 OFF
MASK 5 OFF
MASK 7 OFF
MASK 8 OFF
RETURN
MASK 3 ON
MASK 2 ON