Spectra Logic T-Series Spectra T120 Manual

G4/G5 QIP Upgrade and
Encrypted Media Guide
for
Spectra T120 and Spectra T950 Libraries
PN 90940020 Revision B

G4/G5 QIP Upgrade and Encrypted Media Guide
2
Notices
SPECTRA LOGIC® CORPORATION PROVIDES THE UNIT “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE. INNO EVENT SHALL SPECTRA LOGIC
BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION
OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND, EVEN IF SPECTRA LOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
ARISING FROM ANY DEFECT OR ERROR.
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility
is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may
revise this publication from time to time without notice, and reserves the right to change any product
specification at any time without notice.
G4/G5 QIP Upgrade Guide
Copyright © 2007 Spectra Logic Corporation. All rights reserved.

3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using Media Encrypted with G3 and G5 QIPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The G4/G5 QIP Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Materials and Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Estimated Time Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview of QIP Upgrade Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Removing the G2/G3 QIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the G2/G3 QIP Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the G4/G5 QIP Pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the G4/G5 QIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Returning the G2/G3 QIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Domestic RMA Returns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
International Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4
G4/G5 QIP Upgrade and Encrypted Media Guide
Introduction
The G4 and G5 QIP supports 4 GB Fibre Channel, and may require a library firmware upgrade.
• The G4 QIP does not support BlueScale Encryption and key management.
• The G5 QIP supports BlueScale Encryption and key management.
The upgrade process involved in moving from the G2/3 to the G4/5, including use of media
encrypted using G3 and G5, is reviewed in this guide.
Using Media Encrypted with G3 and G5 QIPs
Media containing data encrypted using the G3 QIP can be read by a partition using a G5 QIP;
however, you cannot append to the tape using the upgraded QIP. To write to the tape with data
encrypted using the G3 QIP, use a partition that uses the G3 QIP.
Note that you cannot read a tape containing data encrypted using a G5 QIP in a partition with a G3
QIP.
Firmware Upgrade
Make sure the library uses BlueScale firmware version 9.8 or higher. If it doesn’t, complete the
firmware upgrade before following the next set of steps.
The G4/G5 QIP Upgrade
This guide includes the procedure for upgrading from a G2 or G3 QIP to a G4 or G5 QIP in a
Spectra T120 or Spectra T950 library. Upgrading to the newer generation QIP requires the
replacement of the pin inside the QIP bay as well as the QIP itself.

5
G4/G5 QIP Upgrade and Encrypted Media Guide
If You Need Assistance
If you need assistance with any part of this procedure, contact SpectraGuard Technical Support by
calling 800.227.4637 or 303.449.0160, or by sending an e-mail to su[email protected].
Materials and Tools Required
Note: After unpacking the upgrade kit, save the packaging. You will need it to pack
up the old QIP and the above listed tools for return to Spectra Logic.
Estimated Time Required
This procedure takes about ten minutes.
The following tools and materials are provided
in the upgrade kit:
• A new G4 or G5 QIP
(not shown)
• A new QIP pin
• A 15-inch extender
• A 3/8-inch ratchet
• A 1/2-inch deep-well socket
• A 3/8-inch bolt extractor
You also need:
• A #2 Phillips screwdriver
Extender
Extractor
Socket
Ratchet
New QIP Pin

6
G4/G5 QIP Upgrade and Encrypted Media Guide
Overview of QIP Upgrade Process
The G4/G5 QIP lets you connect your Spectra T120 or T950 library to 4Gb Fibre Channel HBAs and
switches, which can support data transmission rates of up to 4 gigabits per second.
The entire upgrade process requires only these steps, described in more detail through this guide:
1. Remove the G2/G3 QIP.
2. Change the pin configuration in the QIP bay.
3. Install the new G4/G5 QIP.
4. Power on the library, which is now optionally networked into a 4Gb Fibre Channel HBA or
switch.
5. Check your library firmware. Make sure it is revision 9.8 or higher. If it isn’t, upgrade your library
firmware.
6. Return the G2/G3 QIP you just removed.

7
G4/G5 QIP Upgrade and Encrypted Media Guide
Removing the G2/G3 QIP
1. Use your backup software to stop backups running on the library.
2. Use the soft power button on the front of the library to shut down
power to the library.
3. Shut off the AC power switch on the back of the library.
4. Remove any cabling connected to the G2/G3 QIP(s).
Note: If the QIP you are disconnecting is a Fibre Channel QIP
(F-QIP) and cabled with Fibre Channel cables, you may
want to mark the cabling in some way to remember
which cable plugs in to Port A and which to Port B.
5. Use a #2 Phillips screwdriver to loosen the two captive screws on
the side of the QIP.
Note: The screws are on the right side on a Spectra T950
library, and on the left side on a Spectra T120 library.
Figure 1 A T950 QIP.
6. Pull outward on the QIP’s handle.
7. Set the QIP aside.
8. Proceed to Removing the G2/G3 QIP Pin on page 8.

8
G4/G5 QIP Upgrade and Encrypted Media Guide
Removing the G2/G3 QIP Pin
3. Look inside the QIP bay and locate the old pin; it’s the larger of the two pins protruding from
either end of the board, and not the one at the end of the white 300-pin connector.
Note: In a Spectra T120 library, the pin is near the top of the board. In a Spectra T950
library, the pin is near on the bottom of the board.
4. Carefully reach the extractor inside the library and fit it over the pin, taking extra care not to
damage the 300-pin connector.
5. Unscrew the pin until it comes loose from the board, then remove the pin from the QIP bay.
6. Proceed to Installing the G4/G5 QIP Pin on page 9.
1. Attach the ratchet to
one end of the
extender, and the
bolt extractor to the
other end of the
extender, as shown
in Figure 2.
2. Make sure that the
ratchet is set for
loosening. Figure 2 The assembled pin-removal tool.
Figure 3 The pin in a T120 QIP bay. Figure 4 The pin in a T950 QIP bay.

9
G4/G5 QIP Upgrade and Encrypted Media Guide
Installing the G4/G5 QIP Pin
1. Remove the bolt extractor from the end of the extender.
2. Set the ratchet to tighten.
3. Attach the deep-well socket to the other end of extender.
4. Insert the G4/G5 QIP pin into the socket, as shown below.
5. Carefully reach the extractor inside the library and fit the pin into its hole.
6. Use the extender tool to screw in the pin until it is just finger-tight.
7. Carefully remove the tool from the QIP bay.
8. Proceed to Installing the G4/G5 QIP on page 10.
Figure 5 Inserting the pin into the socket.

10
G4/G5 QIP Upgrade and Encrypted Media Guide
Installing the G4/G5 QIP
1. Carefully unwrap the G4/G5 QIP from its anti-static bag.
2. Use the QIP’s handle to place the QIP into its bay.
3. Push the QIP gently but firmly inward until it clicks into place.
4. Use a #2 Phillips screwdriver to tighten the two captive screws on the side of the QIP.
Note: The screws are on the right side on a QIP installed in a Spectra T950 library, and
on the left side on a QIP installed in a Spectra T120 library.
5. Reattach any cabling that was connected to the QIP.
6. Proceed to Finish on page 11.

11
G4/G5 QIP Upgrade and Encrypted Media Guide
Finish
1. Turn on the AC power switch on the back of the library.
2. Turn on the library using the soft power switch on the front of the library.
3. Wait for the library to come ready.
4. Go to the front of the library and log in to the LC.
The Messages screen may indicate that you need to upgrade firmware.
5. See the library’s user guide for detailed instructions on firmware upgrades.
6. Once the firmware upgrade is complete, use your backup software to restart backups.
This completes the QIP upgrade procedure.
7. Proceed to Returning the G2/G3 QIP on page 12.

12
G4/G5 QIP Upgrade and Encrypted Media Guide
Returning the G2/G3 QIP
Package the G2/G3 QIP and the tools used for the upgrade in the same packaging that Spectra Logic
used to send you the upgrade parts. Make sure to use all of the packing materials provided to prevent
damage during shipment.
Caution: Failure to properly package the QIP may result in damage to the QIP. If a
QIP is damaged in shipping due to improper packing, the warranty is void.
Domestic RMA Returns
Once the QIP and tools have been properly packaged, ship the package to:
Spectra Logic Corporation
ATTN: {RMA Number}
Suite B
5571 Arapahoe Avenue
Boulder CO 80303
Note: You must write the RMA number on the shipping label, or the package will be
returned to you after five days. If you do not know your RMA number, contact
Spectra Logic Technical Support.
International Returns
Spectra Logic arranges for return shipment when a request is made to International Shipping.
1. Fill out your portion of the International Shipping Instructions form, available on the Spectra
Logic Web site.
2. Return the form to Spectra Logic in one of the following ways:
3. When you receive confirmation from Spectra Logic, follow the instructions given to prepare the
component for pickup by the shipper.
E-mail:
[e-mail]
Fax:
303.939.8844
Post:
Spectra Logic
International Returns
1700 N 55th Street
Boulder CO 80301 USA