Spectrum Industries 55498 User manual

Assembly Instructions
0191541R2 Page 1 of 4
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts
or accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Display Stand for AV Credenza Slim
55498
(4) 052605
1/4-20 x 15mm
JC bolts
(2) 0119468
Recessed bumper
w/ 1/4” washer
Tools Required
(32) 0100167
8-32 x 1/2” PH thrd
cutting screws
(3) 021587
8-32 x 1/2” PHMS
(3) 021588
8-32 Keps nut
(2) 059534
1/4-20 x 30mm
JC bolt
(2) 059984
2” Grommet
(2) 0148399
Wall bracket
(2) 0146027
Upright bar
(1) 0145893
Display Stand
(1) 0119747
Fixed TV mount
4mm
(2) 026436
#8 x 1-1/4” PHSM
screw

0191541R2 Page 2 of 4
1. Install upright bars
1. See Figure 1.1 if installing onto a 2-Bay credenza, otherwise proceed with step 1.2.
2. Attach the (2) upright bars together with (3) 8-32 x 1/2” PHM screws and (3) 8-32 Keps nuts. Figure 1.2.
3. Attach the upright bars to the credenza with 8-32 x 1/2” PH thread-cutting screws.
Figure 1.1
8-32 x 1/2”
PHMS
8-32
Keps nut
8-32 Keps nut
(4, 6, or 8) 8-32 x 1/2”
PH thread cutting
screws
8-32 Keps nut
8-32 x 1/2”
PHMS
8-32 x 1/2”
PHMS
Note: (4, 6, or 8) 8-32 x 1/2” PHM screws may be used at each upright
bar attachment point-depending on bay conguration (1, 2, or 3-bay).
Be sure a minimum of (4) are used at each location.
(4, 6, or 8) 8-32 x 1/2”
PH thread cutting
screws
Figure 1.2
Note: If installing the stand onto a 2-bay crendenza, it will be
necessary to remove the (4) screws shown from the credenza
frames before installing the upright bars. Figure 1.1.
2-Bay Credenzas only:
Remove
(4) screws
Upright
bars

0191541R2 Page 3 of 4
2. Install bumpers & grommets
1. Install the (2) recessed bumpers into the upper
corners of the display stand and tighten securely.
Figure 2.
2. Install the (2) grommets.
2” Grommet
(2 req’d)
Recessed bumper
w/ 1/4” washer
(2 req’d)
Figure 2
Display stand
Figure 3
4mm
(8) 8-32 x 1/2”
PH thread cutting
screws
Display
stand
1/4-20 x 30mm
JC bolt
(2 per)
(8) 8-32 x 1/2”
PH thread cutting
screws
3. Install display stand
1. Attach the display stand to the
uprights with (16) 8-32 x 1/2” thread-
cutting screws. Figure 3.
2. Secure the stand to the worksurface
with (2) 1/4-20 x 30mm JC bolts.
Uprights
8-32 x 1/2” PH thrd
cutting screws
(2 req’d)

Note: Display stand must be anchored securely
to wall studs or a solid wall. (2) #8 x 1-1/4”
PHSM screws are provided for wood use.
0191541R2 Page 4 of 4
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2019 Spectrum Industries Inc., All rights reserved.
6. Install wall brackets
1. Remove the monitor.
2. Locate wall framing (if wall studs) and center the wall brackets on a
stud. The bracket can be installed anywhere along the top edge of
the display stand. Figure 6.
3. Slide the credenza up to the wall so the wall brackets contact the
wall. Make sure the credenza is sitting level on the oor. If not sitting
level, the glides can be adjusted to level.
4. Using the brackets as a template, drill suitable holes in the wall for
the fasteners.
5. Secure each bracket to the wall with (1) wall fastener.
Wall fasteners
Figure 6
(2) 026436
#8 x 1-1/4” PHSM
screw
Display Stand
Wall bracket
w/ 3/16” slot
Wall
#8 x 1-1/4”
PHSM screw
(2 req’d)
Figure 5
Display stand
5. Route wires
1. Route monitor wires through
the grommets and down into
the credenza. Figure 5.
2. Secure the stand to the
worksurface with (2) 1/4-20 x
30mm JC bolts.
Note: See instructions included with
monitor mount for installation and setup.
4. Install mount & monitor
(4) 1/4-20 x 15mm
JC bolts
4mm
Fixed TV
mount
Figure 4