Spectrum Industries 95500 User manual

TM
Assembly InstructionsAssembly Instructions
7/16
”
1
/
8”
042023R12 Page 1 of 3
Assembly InstructionsAssembly Instructions
Adjustable CPU SlingAdjustable CPU Sling
9550095500
(1) 042139
Drill template
1. Determine the height and width required for your CPU.
2. Adjust the CPU sling to the height and width of your CPU using the three adjustment holes and attach the corner brackets inside the assembly using
the 1/4-20 x 3/8” truss head machine screws and 1/4-20 locknuts as shown in Figure 1.1. The screws install from the inside with the locknuts on the
outside. Note the positions of the corner brackets at the top and bottom of the sling. Figure 1.2.
Figure 1.1
Corner Bracket
(for desks without
threaded inserts)
Top
Bottom
Figure 1.2
(1) 042110
2” x 2” x 1”
Shim
(4) 021605
#10 x 1-3/4
PHSM
(4) 026547
1/4-20 x 1-1/2
PHMS
Used with 48”, 60”, and 72” desks
1/4-20 Locknut 1/4-20 x 3/8 THMS
Corner Bracket
1/4-20 Locknut
Side overlaps
bracket here
Bottom
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Assemble and adjust CPU sling
1
(2) 042021
Corner Brackets
(7) 042025
1/4-20 x 3/8 THMS
(6) 041943
1/4-20 Locknut
(4) 026017
1/4-20 x 1/2 PHMS
(2) 044890
1 x .275 ID x .5
OD Nylon Spacer
(4) 026057
#10 x 3/4 PHSM
(2) 042020
Sling Side
(3) 0103619
Adhesive bumper
1/2” x 1/16” thick
(1) 0166363
Leg bracket

042023R12 Page 2 of 3
TM
1. Determine if the CPU sling will mount on the right or left side of the desk and align the top sling holes with
the appropriate set of inserts. Figure 2.1, 2.2 shows a sling being mounted on the left side of a desk.
2. Attach the sling to the worksurface using (4) 1/4-20 PHM screws and tighten.
Note: Desks without threaded inserts or support brace use (4) #10
x 3/4” PHSM screws (026057.) Desks without inserts that include a
support brace as in Figure 2.3, use (2) nylon spacers (044890) in the
student-side holes, and one support shim (042110) in the rear holes
using the longer #10 x 1-3/4” PHSM screws (021605). The front of the
CPU sling will extend past the support brace.
Note: Desks with the support brace use (2) nylon spacers
(044890) in the front holes, and the back support shim (042110)
in the rear holes with the longer 1/4-20 x 1-1/2” PHM screws
(026547). The front of the sling will extend past the support brace.
1. Determine if the CPU sling will mount on the right or left side of the desk.
2. Fold and tape the enclosed drill template (042139) to the underside of the worksurface in the
position shown in Figure 2.3. Wrap a piece of tape around a 1/8” drill bit to mark 3/4” from
the end of the bit - Figure 2.4.
3. Carefully drill 3/4” deep through the template at the four marked hole locations. Figure 2.3.
4. Attach CPU sling to worksurface using (4) #10 sheet metal screws.
Figure 2.1 Figure 2.2
1/4-20 x 1/2
PHMS
Threaded
inserts
Support
brace
Nylon
spacer
Threaded
inserts
Shim
1/4-20 x 1-1/2
PHMS
CPU
sling
CPU
sling
Note: Desks without the support brace use
two 1/4-20 x 1/2” PHM screws (026017).
Figure 2.4
Figure 2.3
Drill
template
Worksurface
Drill here
Drill here
Leg
Support brace
(on some desks)
Worksurface
Worksurface
Desks without support brace Desks with support brace
Horizontal
slots
Attach sling to desk
2
With threaded inserts:
Without threaded inserts:
3/4” deep
Drill with
1/8” bit
Tape
Horizontal
slots

042023R12 Page 3 of 3
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2021 Spectrum Industries Inc., All rights reserved.
1. Detemine which type of leg you have (welded or adjustable) and apply
the adhesive bumpers accordingly. Figure 3.1-3.2.
2. Line up the bracket with the front slot of the CPU sling as shown and
install (1) 1/4-20 x 3/8” THM screw (042025). Figure 3.3.
3. Adjust the leg bracket until it is snug against the leg, then tighten 1/4-
20 x 3/8” THM screw to secure.
Note: If the CPU sling is being used on an Evolution™ desk, one of
the included leg brackets should be secured to the sling. This bracket
hooks onto the desk leg to provide additional support for the sling.
Attach leg bracket
3
Figure 3.3
Figure 3.1
Note: The adhesive on the bumpers is designed to work with powder
coated metal and has a strong bond. It is not easy to remove and repo-
sition without damaging the bumper. Be sure each bumper is centered
on the bracket in the locations shown before applying to the metal.
Bumper Installation - Welded leg Bumper Installation - Adjustable (one-piece) leg
Figure 3.2
Leg bracket
CPU Sling CPU Sling
Leg bracket
Bumpers
(optional)
Bumper Bumper
Bumper
0166363
Leg bracket
CPU Sling
Leg
1/4-20 x 3/8”
THMS
Slot in
CPU sling