SpeedAngle GMOS JI100S User manual

GMOS JI100S
QUICK GUIDE
Dashboard Unit Location
Installing Bracket
With 3M Dual Lock tape
Or with AMPS mounts
Or with hand-made mounts
Clicking Device into Place
Insert the left end of the device into the bracket, then click the right end into
place.
Best
Apply the included tape to
the back of the bracket, and
adhere the bracket to a pre-
ferred location. Keep the SA
logo right side up.
If you have an AMPS hole
SDWWHUQPRXQWSOHDVH¿QG
the diagonal holes on the
EUDFNHWDQG¿WWKHPZLWKWKH
corresponding holes on the
mount plate. Then bolt them
together. Keep the SA logo
right side up.
The hole pattern on the
bracket is designed to form
as many regular triangles and
squares as possible to allow
you the maximum freedom
when using hand-made
mounts or zip ties. Keep the
SA logo right side up.
No, unless with external antenna
1 2

Installing Sensor
Installing External Antenna
1. Find a plane on either side of the bike frame that
is parallel to the longitudinal center line of the bike
and vertical to the ground.
3. Clean the surface with alcohol and let dry. Point
the “UP” lettering upward and “FRONT” to the front
of the bike. With the sensor vertical to the ground,
adhere it with the supplied red sponge tape. Let sit
for 24 hours.
4. Align the arrows on the sensor cable head with
device cable head. Connect before switching
the power on. Otherwise, the sensor will not be
recognized by the device.
Install the external antenna when the built-
in antenna reception is poor (erratic trace on
software as below). If you are already using one,
check if it is damaged, or change a location.
The cable run must not be kinked or crushed,
or have a bend diameter less than 2 inch (5 cm).
The cable should be laid as straight as possible.
Then insert the antenna cable plug to the jack on
the dashboard.
Adhere the antenna to a location with a clear
view of the sky, such as the tail. Avoid the en-
gine area. Stay away from the device.
If too tight
Vertical to the
ground
Parallel to the longitudinal
center line
2. Avoid any place that may move, turn, or vibrate
too much, such as handle bar, bike tail, or fairing.
Main frame is the best location.
Main Frame
Please make sure the device, sensor, antenna, and
cables are all properly secured for your safety.

Device Overview
Start Using GMOS
Screen Overview
There are two modes available: Drive mode for street cruising and Timer mode for timing. To swtich to the
RWKHUPRGHHQWHU0HQXJRWR³*2727,0(5'5,9(02'(´DQGSUHVV6(/(&7WRFRQ¿UP
SPEEDANGLE RIDER
RN:S1234567
WWW.SPEEDANGLE.COM
PLEASE CHOOSE SAFETY
OVER PERFORMANCE WHEN
RIDING. BY USING THIS
DEVICE, YOU AGREE TO
ASSUME ALL RISK AND
RESPONSIBILITY
RELATED TO ITS USAGE.
Switch the power on. GMOS will display your
ID, device information, and liability disclaimer,
and then enter Timer mode / Drive mode
depending on which mode you used last time.
You can press any key to skip.
MENU Button, press to enter menu, or,
in a menu, to go to the next menu item.
LED, blinks on when battery is charging.
SELECT Button, press to start / stop
recording, or, in a menu, to execute the
function or adjust the value.
Sensor Connection Cable
External GPS Antenna Connector
USB Port
Power SwitchBacklight Switch
!
TOP
82 75KMH
28
- +
45
33
21
37 45
1 2 3 4 5
6
78
10 9
7
2:30
1. GPS Reception Quality
2. RECÀDVKHVZKHQUHFRUGLQJ
3. Temp Alert, displayed when environmental
temperature is too high or too low.
4. Battery Life
5. Current Time
6. Max angles of the last three turns
7. Max Right/Left angle
8. Lean Angle Meter
9. Current Angle Degree
10. Message Area
11. Top Speed
12. Current Speed
13. G-force Bar, + is acceleration, - is braking
14. Lap CountÀDVKHVZKHQD)LQLVK/LQHLV
crossed
15. Main Display, displays lap time / session
time.Highlighted when a best lap is created if
Sub Display is set as best lap.
16. Sub Display, displays best lap with time gap /
sector time / last lap / lap length
11
14
16
15
13
!
TOP 92KMH
00:52.371
- +
01:24.682 LAP 3
153
12
Drive
Mode
Timer
Mode

Timer Mode
GMOS timer is basically hands free. Just focus on your ride; GMOS will take care of itself. For your refer-
ence, below are things that GMOS will do automatically once you enter Timer Mode:
 To preload track settings to your device, please use the companion software R4
 )RULQIRUPDWLRQRQKRZWRGHVLJQDWHD7UDFNWKDWLVQRWZLWKLQWKH.0VHDUFKUDQJHKRZWRFRQ¿JXUH
your settings such as starting speed, idle time before auto stop, freeze duration of your lap time, and
much more, please see GMOS JI100S User Manual.
Drive Mode
Downloading Logs to Your Computer
Please go to www.SpeedAngle.com/Download to download:
 USB Driver (Double click to start installation.)
 companion software SpeedAngle R4 (Upzip before use).
Connect GMOS to your computer and turn the power on. If this is the frist time you connect to this computer,
wait till the Windows displays “This device is ready for use”. Sometimes this may take a few minutes. Launch
SpeedAngle R4 and click on MENU --> TOOLS --> LOG DOWNLOADER to open the Download dialog. For
more information, please watch the tutorial videos on the download webpage.
GPS Positioning
2:30
TOP 0KMH
- +
GPS IS POSITIONING
PLEASE WAIT...
Track Auto Search
2:30
TOP 0KMH
- +
NO TRACK FOUND
PRESS ANY KEY TO
SET A NEW TRACK
2:30
- +
SEARCH RESULT:
SACUIT EAST
SACUIT WEST
08_25_12 14-38
SET NEW
Standby
2:30
TOP 0KMH
- +
SET NEW
01
TIMER STARTS AT 90KMH
2:30
TOP 0KMH
- +
SACUIT WEST
TIMER STARTS AT 90KMH
2:30
- +
SEARCH RESULT:
SACUIT WEST
SET NEW
2:30
TOP 0KMH
- +
SACUIT WEST
TIMER STARTS AT 90KMH
!
TOP 92KMH
00:52.371
- +
01:24.682 LAP 3
153
Timer / Logging
Auto Start
Timer / Logging Auto
Stop. Lap report Auto
Display.
No Track found. GMOS
will set a new Track when
the timer starting speed is
reached.
One Track found. GMOS
will use it directly. Multiple Tracks found. Press MENU
to go to the Track you want, and then
press SELECT to confirm.
If no Track is selected, GMOS will set a
new Track when timer starts.
This result will display for 90 seconds.
To skip, press SELECT.
Press SELECT to
start / stop recording.
Press SELECT to change Time Zone.
Press SELECT to change KMH / MPH.
Clear memory when you see “MEMORY
FULL” or “LOGS FULL” in the message
area.
SYSTEM MENU. Press MENU to
enter.
It stops when the preset
idle time is reached.
SYSTEM JAN/01/11
12LOGS, 85% MEM LEFT
RESET MAX ANGLE 37,42
RESET TOP SPEED 108
ANGLE THRESHOLD 10 KMH
TIMEZONE GMT -8
UNIT MPH/KMH KMH
CLEAR MEMORY
LCD BRIGHTNESS 2
GO TO TIMER MODE
SAVE SETTINGS AND EXIT
SYSTEM JAN/01/11
12LOGS, 85% MEM LEFT
Timer will auto start when
this speed (configurable) is
reached.
??
1123 1912 LOSAIL
28:09 9 LAPS
BEST L007
2:23.502 166 125
AVERAGE
2:44.750 171 111
DETAIL