SpeedyBee F405 WING APP User manual

Home » SpeedyBee » SpeedyBee F405 WING APP Fixed Wing Flight Controller User Guide
Contents [ hide
1 SpeedyBee F405 WING APP Fixed Wing Flight
Controller
2 Product Information
3 Overview
4 Usage Instructions
5 Specification Overview
6 Assembly Instructions
7 Hardware description
8 Wiring Diagram
9 Firmware upgrade and APP connection
10 Documents / Resources
11 Related Posts
SpeedyBee F405 WING APP Fixed Wing Flight Controller
SpeedyBee F405 WING APP Fixed Wing Flight Controller User
Guide
https://parasim.prom.ua/

Product Information
The Quick Start Guide TOPBoard FC Board is a wireless board designed for use in drones. It includes a PDB
board and a USB extender. It supports INAV / Ardupilot firmware and can be powered by a 2-6S LiPo battery with
52cL x 32cW x 19cH mm dimensions and a weight of 35g with the USB extender. The board features wireless
configuration, LED strip controller, and battery level indicator. It also comes with a Speedybee APP Installation
guide.
Overview
Usage Instructions
After assembling the board, connect it to your drone’s power source and configure it using the Speedybee APP
installation guide. The board supports INAV / Ardupilot firmware and can be used to control motors and servos
with the motor and servo output pin header. The board also includes a buzzer, USB TYPE-C port, buzzer mute
switch, FC RGB status indicator, and a BOOT button. Press and hold the BOOT button while powering on to enter
DFU mode for firmware flashing. When the FC is powered on and in operating state, the BOOT button is also
used for controlling other functions of the wireless board.
Specification Overview

Product Name: Quick Start Guide TOPBoard FC Board
Part 1 – Overview: PDB Board, USB extender, Wireless configuration, LED strip controller, Battery level
indicator
Part 2 – Hardware Description: Digital VTX solder pads, MicroSD card slot, Telemetry module solder pads,
SBUS input pin header, GPS module solder pads, Analog VTX connector, Analog camera connector, Airspeed
sensor solder pads, ELRS receiver pin header, UART6 solder pads, Motor and servo output pin header
Supported Firmware: INAV / Ardupilot
Power Input: 2-6S LiPo
Dimension: 52cL x 32cW x 19cH mm
Weight: 35g with USB extender
Wireless Configuration: Supported
LED Strip Controller: Supported
Battery Level Indicator: Supported
Product Name SpeedyBee F405 WING APP
TOP Board SpeedyBee F405 WING Wireless Board
FC Board SpeedyBee F405 WING FC Board
PDB Board SpeedyBee F405 WING PDB Board
USB extender SpeedyBee F405 WING USB extender
Wireless configuration Supported
LED strip controller Supported
Battery level indicator Supported
FC Firmware INAV / Ardupilot
Power Input 2-6S LiPo
Dimension 52L x 32W x 19H mm
Weight 35gwith USB extender
Assembly Instructions

Assembly order
1. Align the pin headers between boards A and B then press the two boards together tightly.
2. Install both boards A and B onto board C, and tighten the screws.
Refer to the diagram for assembly order:
Hardware description
FC Board Front

FC Board Back

USB extender front

PDB board Front
Wireless board Front

Wireless status indicator (RGB LED)
The wireless board has built-in telemetry function , which includes 4 RF modes: Bluetooth BLE, Wi-Fi, classic
Bluetooth SPP, and wireless off mode.w
Green: low power Bluetooth BLE mode.
White: Wi-Fi mode.
Blue: classic Bluetooth mode.
The RGB LED is off: wireless off mode
Press and hold the BOOT button for 3seconds to switch between the 4 wireless modes. A quick flashing
yellow LED indicates a successful mode switch.
LED mode indicator(orange LED):
Orange light always on: Solid orange LED means the 4 sets of LED strips are in SB_LED mode,
controlled by the wireless chip. A short press of the
BOOT button cycles through different display effects when the FC is operating normally.
Orange light is off – Off orange LED indicates FC_LED mode, where the FC controls the 4 sets of LED
strips directly. Press and hold the BOOT button for 2 seconds to switch between FC_LED mode and
SB_LED mode

Wiring Diagram
Method 1: Plug and play
Method 2: Direct soldering.

Firmware upgrade and APP connection
Firmware upgrade
SpeedyBee F405 WING APP not supporting wireless firmware flashing, please update the firmware on a
computer. Follow these steps:
1. Press and hold the BOOT button , and connect the FC to the computer via USB cable.
2. Open the INAV Configurator on your computer, go to the “Firmware Flasher ” page, select the light controller
target as “SPEEDYBEEF405WING”, and then flash the firmware.
3. To flash Ardupilot firmware, follow the same steps as above, select “Load Firmware [local]”, and then flash the
firmware.
APP connection
Connecting Ardupilot firmware to QGroundControl app.
Check the color of the wireless status indicator. If it’s not flashing white, press the BOOT button for 6 seconds to
switch to white. Then connect to the “Speedybee F405Wing” Wi-Fi and open QGroundControl, it will automatically
connect.

APP
Connecting INAV Firmware to Speedybee APP.
Check the color of the wireless status indicator . If it’s slow flashing green, open the SpeedyBee app and follow
the steps to connect to the corresponding product.
Documents / Resources