Sper scientific 800019 User manual

1 1
Bluetooth®
Hygrometer
800019
Instruction Manual

2 3
TABLE OF CONTENTS
INTRODUCTION..........................................3
PANEL DESCRIPTION................................4
MEASUREMENT PROCEDURES...............5
AC WEIGHTING SCALES...........................5
BACKLIGHT.................................................5
HOLD FUNCTION........................................5
MAX/MIN FUNCTION...................................6
AUTO POWER OFF.....................................7
BLUETOOTH COMMUNICATIONS.............8
BATTERY REPLACEMENT.......................11
SPECIFICATIONS......................................12
OPTIONAL ACCESSORIES......................13
WARRANTY...............................................16

2 3
INTRODUCTION
Sper Scientic’s Bluetooth® Hygrometer is
small, light, and simple to use. Displays
humidity, wet bulb, dew point and air
temperature in °C or °F on the meter’s
large 1-½” backlit display. Features a bar
graph display, minimum and maximum hold
(peak) and data hold functions. The meter
o󰀨ers the convenience of Bluetooth® for
wireless communication with free iOS and
Android smart phone Apps. Results can
also be remotely viewed on your smart-
phone in real time, saved and exported.
This enables the meter to be used as a
remote wireless probe and as a datalogger.
Comes ready to use with tripod screw,
instructions and a 9V battery. N.I.S.T.
traceable certicate of compliance available.

4 5
PANEL DESCRIPTION
1. Temperature/
RH Sensors
2. LCD Display
3. HOLD/ button
4. MAX/MIN button
5. Power button
6. Temp. Mode button
7. Bluetooth button
1.
2.
3.
4.
5.
7.
6.

4 5
MEASUREMENT PROCEDURES
1. Turn the meter on/o󰀨 by pressing the
POWER button.
2. RH (Relative Humidity) will appear in large
digits on the lower display and temperature
in smaller digits on the upper display.
3. Hold the red button down for 2 seconds to
toggle between temperature readings in
°C and °F.
4. Press the red button to toggle between
WB (Wet Bulb), DP (Dew Point) and
ambient temperature.
BACKLIGHT
Press for 2 seconds to turn the illuminated
display on/o󰀨.
HOLD FUNCTION
With the meter on, press the HOLD button

6 7
to display “HOLD” and the last reading. Press
HOLD again to exit this function.
MAX/MIN FUNCTION
Max/Min readings are continually updated as
soon as you enter the Max/Min mode. These
readings are reset when you exit the Max/ Min
mode, or when the meter is turned o󰀨.
1. Press the MAX/MIN button once to display
“MAX” and the maximum (peak) recorded
RH and Temperature. The display will be
updated only when the max (peak) RH and
Temperature levels are exceeded.
2. Press the MAX/MIN button again to display
“MIN” and the minimum RH and Tempera-
ture. The display will be updated only on
reaching lower RH and Temperature read-
ings.
3. Press the MAX/MIN button again to exit
Max/Min mode. The current reading is now
displayed and continually updated.

6 7
AUTO POWER OFF
1. If no buttons are pushed for about 10 min-
utes, the meter will automatically turn o󰀨.
2. While the meter is on, press the power
button for 2 seconds to override Auto Power
O󰀨: disappears from the display indicat-
ing that Auto Power O󰀨 is disabled.
Note…The meter defaults to Auto Power O󰀨
each time it is turned on.

89
BLUETOOTH®COMMUNICATION
Download and pairing
1. Download the iOS or Android “Meterbox
Pro” APP to your smartphone.
2. Press the button on the meter to activate
Bluetooth®.
3. Press “Connect Device” on the APP.
4. Now choose “800019” from the device list
that now appears. The meter will immedi-
ately begin displaying a real time graph of
your meter’s readings.
Saving your results
5. To begin recording data press the red
button on screen. You will now be asked to
name and save the le. The data will now
start recording. Press the red button again
to stop recording.

89
Viewing saved Data
6. Press < at the top of the screen to view
saved data. Next, choose “Files” at the
bottom of the screen, then choose the le
you wish to view. A graph of the entire
record will now appear. Press on the
lower right to see the data including
recording times, maximum, minimum and
average readings.
7. (saved data le graph) enables you to
add notes and photos to your data le.
8. Press at the top of the screen to export
the data for to your computer for further
analysis or storage.

10 11
Settings
Alarms:
1. Select Instrument Type: Environmental
Meter.
2. Press Next then Choose Function and
select your alarm parameter.
3. Insert your Hi and Low alarm values.
4. Repeat steps 3 & 4 for additional alarm
parameters you wish to set for your meter.
5. Use the Alarm switch at the bottom to
enable / disable the alarm for the parameter
shown. Use the Allow Alarm switch at the
top to enable / disable alarms on all
parameters.
Recording: Choose your test sample rate
and duration.