Sper scientific 850068 User manual

Hybrid–Powered
Environmental Quality
Meter
850068
Instruction Manual

- 2 -
Hybrid-Powered Environmental Quality Meter 850068
Copyright ©2009 by Sper Scientific
ALL RIGHTS RESERVED
Printed in the USA
7720 E. Redfield Rd. Suite #7, Scottsdale, AZ 85260
Tel: [phone] Fax: [phone]
Web: www.sperscientific.com
The contents of this manual may not be reproduced or
transmitted in any form or by any means electronic,
mechanical, or other means that do not yet exist or
may be developed, including photocopying, recording,
or any information storage and retrieval system
without the express permission from Sper Scientific.
www.ponpe.com

- 3-
MATERIALS SUPPLIED.................. 4
INTRODUCTION ................................... 5
FEATURES .................................... 7
UNIT DESCRIPTION ...................... 8
LCD DISPLAY ................................. 9
KEYPAD ......................................... 10
POWER TYPE SELECTION ........... 11
MEASUREMENT PROCEDURES... 12-21
BATTERY REPLACEMENT ............ 22
TROUBLESHOOTING..................... 23
ERROR CODES.............................. 23
SPECIFICATIONS........................... 24
OPTIONAL ACCESSORIES............ 26
ENVIRONMENT REFERENCES..... 27
WARRANTY .................................... 28
TABLE OF CONTENTS
www.ponpe.com

- 4 -
MATERIALS SUPPLIED
 Meter
 Anemometer Vane Probe
 Water-Resistant Plastic Case
 One DC 9V Battery
 Instruction Manual
www.ponpe.com

- 5-
The Sper Scientific Hybrid-Powered
Environmental Quality Meter 850068 is a 4
-in-1 instrument that functions as a:
 Light Meter—measures light using an
exclusive photodiode and color-
correction-filter, light sensor. Meets the
Commission Internationale de
l’Eclairage (CIE) photopic standards.
 Anemometer—measures wind-speed
using a low-friction, ball bearing wheel
design to provide exceptional accuracy.
 Hygrometer—measures relative
humidity using a high-precision
humidity sensor with fast response
time.
 Thermometer—measures temperature
using standard Type-K (NiCr-NiAl)
thermocouple input jack for all Type-K
probes (optionally available).
INTRODUCTION
www.ponpe.com

- 6 -
The rugged, light-weight and portable
design of the Environmental Quality Meter
allows you to use it almost anywhere to
monitor elements and maintain a healthy
and safe environment.
The Hybrid-Powered Environment Quality
meter also offers a Green power source
through a built in hand-crank generator,
enabling battery-free operation.
Recommended exposure limits for the
various elements have been set through
government organizations such as the US
Occupational Safety and Health
Administration (OSHA) and the National
Institute for Occupational Safety and
Health (NIOSH).
Current recommendations and guidelines
are available through these organizations,
as well as many others. (Refer to
Environment References page 27.)
INTRODUCTION
www.ponpe.com

- 7-
 Multi-Purpose 4-in-1 Meter
 Hybrid-Power (Hand-Crank Generator)
 Rugged, Light-Weight, and Portable
 Accurate and Easy-to-Use
 One-Button Control
 Hold
 Minimum and Maximum Recall
 Multi-Channel Display
 Tripod Mountable
 Data Analysis through PC Connection
 Zero Offset Adjustment
 Easy Calibration
FEATURES
www.ponpe.com

- 8 -
UNIT DESCRIPTION
Light
Sensor
Generator Hand-Crank
(Bottom of Unit)
Easel Stand
(Back of Unit)
LCD
Display
Key
Pad
Humidity Sensor
(Top of Unit)
Temperature Thermocouple and
Anemometer Probe Input Ports
(Top of Unit)
Tripod Screw
and Battery
Compartment
(Back of Unit)
Power Type
Switch
(Side of Unit)
www.ponpe.com

- 9-
LCD DISPLAY
Light–Level Measurement Units
Lux
Ft-cd
x10
Both Lux and Ft-cd (Foot Candle)
measure luminance.
Lux = lumens per square meter.
Ft-cd = lumens per square foot .
X10 = Value displayed is 1/10 the value.
Air Velocity Measurement Units
ft/min
m/S
km/h
MPH
knots
Feet per minute
Meters per second
Kilometers per hour
Miles per hour
Nautical miles per hour
Relative Humidity Measurement Units
%
Relative humidity (RH) is a term used to
describe the amount of water vapor that
exists in the air and displays as a
percentage.
Temperature Measurement Units
°C/°F Represents the temperature in either
Celsius or Fahrenheit degrees.
Record Mode and Hold Indicators
REC
MAX
MIN
HOLD
Meter is operating in Record Mode.
Maximum value recorded.
Minimum value recorded.
Meter display is in Hold Mode.
www.ponpe.com

- 10 -
KEY PAD
Turns the unit on/off
Freezes current measurement value
Clears recorded min/max values
Enters Record Mode
Displays recorded min/max values
Changes unit of measure for an-
emometer
Calibrates the light sensor
Changes unit of measure for light
meter and temperature scale
Selects measurement mode
www.ponpe.com

- 11 -
POWER TYPE SELECTION
Hybrid Power (Green) Selection
1. Slide the Power Type Switch up to the
Gposition to use the meter’s Green
power source instead of battery power.
The low battery indicator will
display in the upper left
corner of the LCD display.
2. Lift and extend the generator’s hand-
crank located at the bottom of the unit.
3. Rotate the handle clockwise to windup
or crank the generator to create power
for the meter.
Cranking the meter’s generator for 20
seconds will offer several minutes of
energy. Use as needed for efficient
Green-power operation.
www.ponpe.com

- 12 -
POWER TYPE SELECTION
Battery Power Selection
1. Ensure that you have correctly installed
the 9V battery in the battery
compartment. (Refer to Battery
Replacement page 22).
2. Slide the Power Type Switch down to
the Bposition to use the meter’s
battery power source instead of Green
power.
Note…
The battery life is greater than 1000 hours
when using alkaline batteries (250 hours
when using general purpose batteries).
Light-Level Measurement
1. Press POWER to turn the meter on.
2. Press FUNCTION until the meter
displays the Lux or Ft-cd light-level
measuring unit.
3. Press LUX/FT-CD to select between
Lux and Ft-cd.
4. To ensure measurement accuracy,
calibrate the light meter using the Zero-
Offset adjustment feature. To
calibrate:
MEASUREMENT PROCEDURES
www.ponpe.com

- 13 -
MEASUREMENT PROCEDURES
5. Cover the light sensor to block any light
from registering on the meter. Press
ZERO to calibrate the meter to zero.
The meter displays the light-level value
as 0 and is ready to measure light,
even in low-lit and dark areas.
6. Uncover the light sensor and ensure
that the light sensor on the front of the
meter is pointing toward the lumination
subject and is free from obstruction.
7. The meter measures the light level of
the surrounding environment and
displays the reading.
When measuring intense light, the
meter displays x10 to indicate that the
value displayed is 1/10 the actual value.
www.ponpe.com

- 14 -
MEASUREMENT PROCEDURES
Air-Velocity Measurement
1. Ensuring correct pin alignment, insert
the Anemometer plug into the PROBE
IN Anemometer socket located at the
top of the unit.
2. Press POWER to turn the meter on.
3. Continuously press FUNCTION until
the meter displays the wind-speed and
ambient temperature measuring units
(ft/min, m/S, km/h, MPH, knots, °C, °F).
3. Continuously press UNIT to select the
desired wind-speed measuring unit.
4. Press °C/°Fto select between a
Celsius (°C) and Fahrenheit (°F)
temperature reading.
5. Hold the Anemometer Vane Probe and
ensure that the Anemometer Vane
Probe Head and air flow sensor is free
from obstruction.
www.ponpe.com

- 15 -
6. Face the air-flow sensor (marked with a
yellow dot) in the direction of the wind.
7. The meter measures the wind-speed
and ambient temperature of the
surrounding environment and displays
the value.
MEASUREMENT PROCEDURES
www.ponpe.com

- 16 -
Relative Humidity Measurement
1. Press POWER to turn the meter on.
2. Continuously press FUNCTION until
the meter displays the relative humidity
and ambient temperature measuring
units (%RH, °C, °F).
3. Press °C/°Fto select between a
Celsius (°C) and Fahrenheit (°F)
temperature reading.
4. Ensure that the humidity sensor is free
from obstruction.
5. The meter measures the relative
humidity and ambient temperature of
the surrounding environment and
displays the value.
Note…
When moving the meter to a new
environment, it may take a few minutes
for the humidity readings to stabilize.
MEASUREMENT PROCEDURES
www.ponpe.com

- 17 -
Thermocouple Temperature
Measurement
This procedure requires an optional Type-
K thermocouple probe.
1. Press POWER to turn the meter on.
2. Ensuring correct polarity (+ –), carefully
plug any Type-K thermocouple probe
into the Temperature Thermocouple
Input Port at the top of the meter.
Temperature differences between the
probe and the meter may cause
inaccurate results. Allow a few minutes
for the probe and meter to adjust to
ambient temperature.
3. Continuously press FUNCTION until
the meter displays the temperature
measuring unit (°C, °F).
4. Press °C/°F to select between a
Celsius (°C) and Fahrenheit (°F)
temperature reading.
5. Make contact between the thermo-
couple sensor probe and the object you
want to measure.
6. The meter measures
the temperature of the
object and displays the
value.
MEASUREMENT PROCEDURES
www.ponpe.com

- 18 -
Hold Mode Selection
1. Press POWER to turn the meter on.
2. Using the FUNCTION button, select
your desired measurement function
(Light, Air-Velocity, Relative Humidity,
or Temperature).
3. When a value displays that you want to
retain, press HOLD.
The meter freezes the current
measurement value and discontinues
measurement while in Hold Mode.
4. Press HOLD again to exit Hold Mode
and resume measurement.
MEASUREMENT PROCEDURES
www.ponpe.com

- 19 -
Record Mode & Auto-Off Selection
To save battery life, the Environmental
Quality Meter turns off automatically after
10 minutes of inactivity. To override this
feature:
1. With the meter turned on, press MAX/
MIN. The meter displays REC,
disables the Auto-Off feature, enters
Record Mode and begins recording
maximum and minimum values.
2. While the meter displays REC and
when you are ready to view the
maximum and/or minimum measured
values, press the MAX/MIN button.
(The MAX/MIN button toggles between
the maximum and minimum measured
values.)
MEASUREMENT PROCEDURES
www.ponpe.com

- 20 -
3. To clear the max/min values and
continue recording, press HOLD. The
meter clears the previously recorded
max/min values and enters Record
Mode.
4. To exit the Record Mode, press and
hold MAX/MIN for 2 seconds.
The meter exits Record Mode, displays
the current reading value, and resets to
automatically turn off after 10 minutes
of inactivity.
MEASUREMENT PROCEDURES
www.ponpe.com