Spl Lil'kicker d1316 User manual

Thank you for purchasing this Sound Percussion Labs™ drum set. Please take a few moments to familiarize yourself

with this set-up guide so you can assemble your new drums quickly and easily. For additional information as well

as troubleshooting advice and parts requests, please visit www.soundpercussionlabs.com

WARNING: Choking hazard – small parts. Not for children under 3 years old.

SET INCLUDES:

A16”x 12” Bass Drum Shell

B8”x 5” Mounted Tom Drum

C10”x 4” Snare Drum

D16” Clear Batter Side Bass Drum Head

E16” Black w/logo, Resonant Side, Bass Drum Head

Note: Snare Drum and Tom heads are already

installed on snare and tom.

FTwo Bass Drum Legs

GTom Arm

HSnare Drum Stand

IHi-Hat Stand

JCymbal Arm

KCrash/Ride Cymbal

LPair of Hi-Hat Cymbals

MTwo Bass Drum Hoops

NBass Drum Pedal

OBass Drum Beater

PPair of Drumsticks

QDrum Throne

R12 Washers

S12 Long Tension Rods

TDrum Key

UThumbscrew for Snare Stand

VBolt and Wingnut Set for Hi-Hat Stand

W12 Bass Drum “Claws”

FD E

T U VW

Adult assembly required

COMPLETE 3-PIECE KIT

Lil kicker

DRUM

SET OWNER’S MANUAL M

D1316

10182 SPL D1316 Li'l Kicker Assembly Manual.indd 1 6/5/14 4:52 PM

3-Piece Drum Set Owner’s Manual

Lil kicker

1. Place the bass drum logo head (E) over front of the bass

drum shell (A) and center logo.

2. Place one of the bass drum hoops (M) onto drum head.

3. Insert long tension rod (S) / washer (R) / bass drum claw

(W) hook assembly into bass drum lug. Make sure the

claw hook is secure on the bass drum hoop. Tighten with

your ﬁngers.

4. Repeat this for all the lugs on one side of the drum.

5. After all tension rods on one side are ﬁnger tight, use the

drum key (T) to tighten the #1 tension rod 3 turns. Follow

these steps for tension rods #2 through #6 in a criss-cross

pattern as shown. Repeat this pattern, tightening each rod

one half turn until the drum head is taut and wrinkle free.

6. Repeat for the clear batter head (D) on the opposite side

of the drum.

Bass Drum Head Assembly

Bass Drum Leg Assembly (Spurs)

Washer

Bass Drum Hoop

Bass Drum Claw

Bass Drum Long

Tension Rod

Shell

Bass Drum Lug

1. Insert both legs (F)

through the assemblies

at bottom sides of the

bass drum and tighten

screw with drum key.

2. Adjust the angle to

ensure bass drum sits

evenly on the ﬂoor

when positioned.

FRONT

BACK - Drummer’s Side

Attaching Bass Drum Pedal

1. Insert the bass drum

beater (O) into the

bass drum pedal (N)

and tighten with the

drum key.

2. Attach bass pedal to

the bass drum hoop

using the toe clamp.

3. Tighten the wingnut

on the toe clamp

until secure.

4. Position the bass

drum beater to strike

the center of the

bass drum.

10182 SPL D1316 Li'l Kicker Assembly Manual.indd 2 6/5/14 4:52 PM

SoundPercussionLabs.com

Mounted Tom Assembly - to Bass Drum

Support Collar 2

Support

Collar 1 Support Collar 2

Thumb screw on

bass drum mount

(top view)

1. Set desired height of the support arm (G) using

thumb screws on bass drum mount (located on top

of bass drum).

2. Loosen Support Collar 1 using drum key. Then, slide

support arm down to ﬁt into bass drum mount.

Make sure to align collar nub into indentation on

mounting base.

3. Set angle of support arm to desired angle

& tighten thumb screw.

4. Using drum key, loosen Support Collar 2.

5. Slide mounted tom drum (B) onto support arm &

tighten Support Collar 2. The mounted tom drum

should be located to the left when drumming.

Snare Drum Stand Assembly

Snare Arms

(basket)

Tilter

Assembly

Height

Adjustment

Insert Wingnut

Hi-Hat Cymbal Stand Assembly

1. Extend legs of Hi-Hat Stand (I) into

open position and tighten set screw.

2. Place center arm of pedal at stand

base and insert bolt through bottom

opening. Secure with washer and

wingnut (V) on top.

3. Slide upper tube over inner rod of

leg assembly and tighten set screw.

4. Place one Hi-Hat cymbal (L) onto

seat as shown.

5. Attach 2nd Hi-Hat cymbal (L) to

clutch assembly by placing cymbal

between felts of Hi-Hat clutch.

6. Slide clutch assembly (set screw

at top) cymbal onto Hi-Hat rod

and tighten set screw. Position top

cymbal about ½" from bottom.

7. Finished Hi-Hat cymbal stand should

look like this. When pedal is pressed

down with foot, the top cymbal will

be brought down to closed position.

Upper Tube

Inner Rod

Hi-Hat Clutch

Hi-Hat

Cymbal Seat

345

1. Extend legs of snare drum stand (H) into

open position. Adjust down to top of line indication

mark at leg base. This will ensure maximum stability

for the snare drum stand.

2. Insert wingnut (U) into middle snare arm.

3. Adjust the basket to the angle shown with the

tilter assembly.

4. Place snare drum (C) in snare basket. For best

playability, position top adjustment angle of

snare stand so snare drum playing surface sits ﬂat.

Increasing angle of adjustment can cause snare

drum and stand to fall over and may cause injury.

Position the arms to ﬁt snug to the drum.

Leg Adjustment

Line Indication Mark

10182 SPL D1316 Li'l Kicker Assembly Manual.indd 3 6/5/14 4:52 PM

Top View of Drum Placement

Bass Drum

Pedal

Mounted

Tom Cymbal

Snare

Hi-Hat

Cymbal Arm Assembly

Drum Throne Assembly

1. Slide cymbal arm (J) into mount of bass drum and set

desired height using wingnut.

2. Place cymbal (K) between felt pads. Tighten wingnut

above cymbal only enough to hold cymbal and felts, but

loose enough to let cymbal move freely when struck.

3. Set desired cymbal angle using tilter adjustment.

1. Fold out legs at base of Drum Throne (Q).

2. Place center tube into base and tighten height adjustment

wingnut. It is recommended to place wingnut as shown for

comfortable playing style.

3. Place seat top and tighten wingnut.

Do not use drum seat for other uses than its intended purpose

as a seat. Do not stand on throne.

Cymbal goes here

Warranty

One (1) Year Limited Warranty

Subject to the limitations set forth below, Sound Percussion Labs™hereby represents and warrants that the components of this product shall be free from defects in workmanship and materials,

including implied warranties of merchantability or ﬁtness for a particular purpose, subject to normal use and service, for one (1) years to the original owner from the date of purchase.

Limits of Liability

Retailer and manufacturer shall not be liable for damages based upon inconvenience, loss of use of product, loss of time, interrupted operation or commercial loss or any other incidental or

consequential damages including but not limited to lost proﬁts, downtime, goodwill, damage to or replacement of equipment and property, and any costs of recovering, reprogramming, or reproducing

any program or data stored in equipment that is used with Sound Percussion Labs™products. This guarantee gives you speciﬁc legal rights. You may have other legal rights which vary from state