Splash SuperPools TitanPool3 User manual

By
Owner’s Guide

2
Table of Contents
Congratulations 3
Titan3 Parts List 4
Site Preparation & Rectangular Pool Set-up 5-7
Round Pool Parts List and Set-up 8-10
Care and Winterizing of your Titan3 11
Important Reminders 12
Box 4 Contents and Instructions 13
Splash Ladder Assembly
Additional Information
Never leave children or other inexperienced swimmers
alone in the pool!

3
Congratulations on purchasing your
TitanPool3 ,
from Splash SuperPools, Limited.
You have purchased one of the finest above ground pools on the market,
in it’s price range. We at Splash have designed and built your pool with your
enjoyment and safety in mind. The following installation and owner’s guide
contains important instructions and safety advice. Please read it carefully.
Throughout this Guide there may be pictures of a pool with different color
structure or material than your TitanPool3. The color is the only difference
and the assembly is the same.
If you have any questions, please contact your Titan3 Dealer.
Remember: Children are fascinated with the pool and the water.
Always lock your safety ladder in the up and locked position to prevent
unauthorized entry into the pool when proper supervision is not available .
WARNING: The water in your TitanPool3 is shallow (at 4ft deep)! Never dive
or jump into the pool, as serious injury could occur!
NEVER Leave children or inexperienced swimmers alone in or near the
pool!

4
Titan3 Parts List
A. Pool Liner (Not Shown Here)
B. Male Top Rail End Section
C. Middle Top Rail Section
D. Female Top Rail End Section
E. Pool Leg
F.
Galvanized Connection Pin
G.
Stainless Connection Ring
H.
Optional FootBlock (Purchased Separately)
Optional Footblocks
B
C
D
E
G
F
H

5
First Steps
Selecting the best location for your pool.
1. Locate a level site for the pool, as it should not be set up out of level by
more than one (1) inch. If such a location is not available, some ground work will be
necessary to achieve a level area for the pool.
2. Never locate your pool under power lines nor is it recommended to locate in an easement.
3. It is best to locate your pool as close as possible to a GFI (ground fault interruption) protected
electrical outlet with a weather cover.
4. Inspect the selected site to remove all sharp objects, such as stones, sticks or other similar
objects. The cleared area should be 2ft larger all around the pool to allow for room to set up the
pool and for full leg extension. It is best to provide a 2” fine sand base for maximum protection
of your
TitanPool3 liner. If this is not available, a heavy gauge visquene separation sheet will
help to protect your liner.
5. Your Titan3 is approximately 49” tall when filled with water. Some localities do not require the
homeowner to obtain permits or to install a fence, if the pool wall height is more than 48” above
ground level. HOWEVER, it is the homeowner’s responsibility to meet all applicable safety,
health code and zoning regulations.
Now for the pool set-up:
1. Unfold your pool liner on your selected, prepared site.
2. Refer to the Box 4 instructions later in this manual for installing the fittings and hoses for
the skimmer and pump system. Be careful to locate the reinforced fitting holes closest
to the GFI protected power outlet.
3. Start by first inserting one (1) female end section of the top rail (C) through the slot in the
corner of the white top rail sleeve, followed by adding Middle Top Rail Sections (B), making
certain to insert the Section (B) into the end of the Section (C) and rotating this new section
until the snap pin in the male end of each part pops into the hole in the female companion
section. Continue with this process until the last piece (male end piece) is inserted to complete
the wall. Adjust the Top Rail pipe by rotating to align the holes in the Top Rail pipe with the
holes in the Top Rail Membrane. Continue installing each Top Rail Section until all four Top
Rails are completed.

6
4. Distribute the Legs (E) with two (2) stainless steel rings (G) slid onto each Leg (E) around the
perimeter of the pool. Next, insert one end of the Leg into the top rail hole closest to the end.
Put your foot against this leg end and stretch the other end of the leg until it fits into the next
top rail hole. Continue this process around the entire pool until all legs are inserted firmly into
the top rail.
5. The next step requires a minimum of two people. While one person lifts the top rail and legs up,
the second person should insert the galvanized connection pin (F) thru the sleeve of the pool
footstrap, thru the stainless steel rings and centered in the footstrap. Continue this process on
each pool leg until all are installed. At this point, the pool is ready for water, if the Easy Clean
Pump/Filter was purchased with your Titan3. If not, refer to the instructions in the Box 4.

7
6. If Footblocks (H) have been purchased separately for your Titan3, distribute a FootBlock around
your pool at each leg. Attach a FootBlock to the base of each leg using the provided attachment
fittings. Then, during the course of filling the pool with water, make certain that the top of the
pool legs are still inserted into the top rail (or damage could occur to the white top rail
membrane), and that the foot straps are fully extended all around the pool.
Filling your
TitanPool3
1. Your Titan3 will not stand up completely by itself at this point. However the walls will stand up
enough to allow for the longer wall top rail to fit inside of the shorter end walls. There must be a
solid support under each leg because, when the pool is filled, the weight on each leg will be
approximately 2000 lbs, and the leg will sink into soft ground. Either the Splash Footblock
should be used, or pressure treated two (2) 2” X 10”s cut approximately18” long should be
inserted under each leg and set into the ground.
2. When the pool water depth has reached about 1”, stop filling. Pull all foot straps to assure they
are tight and that the foot is centered on the support base or FootBlock. Also check all legs to
assure they are fully inserted into the Wall Top Rail metal pipe. Continue filling with water.
3. The Pool is full when the water level reaches a level about 3-4” from the Top Rail. You can use
the Warning Labels inside the pool as a gauge of the water level.
4. IF THE FLOATING WEIR AND THE INTERNAL BASKET OF THE SKIMMER ARE REMOVED, THE
RESULTING STRONG SUCTION CAN TRAP HAIR OR OTHER BODY PARTS IF THEY ARE
INSERTED INTO THE SKIMMER.
NEVER WORK ON THE PUMP, FILTER, OR SKIMMER WHILE THE PUMP IS OPERATING,
OR SERIOUS INJURY COULD OCCUR DUE TO STRONG SUCTION!!

8
Parts List for Titan3 Round Pool
A. Galvanized Top Structure
B. Bottom Structure
C. White Upright Structure
D. Bag with Clear Elastic Plastic Hose and Connecting Pins (E)
F. Pool Liner (Not Shown)

9
Titan3 Round Pool Assembly Instructions
1. Survey your yard to determine the best, level location for your Pool. Remember do not install
under Power Lines. Local a level area approximately two (2) ft in diameter larger than your pool,
to allow enough space for the legs. Also, make certain that the area has easy access to an
appropriate GFI Protected Outdooor electrical outlet.
2. Remove all rocks, sticks and any other sharp objects from the area where the pool will be
installed.
3. Your Titan3 Pool will stand about 49” tall, when filled with water. Some localities do not require
the homeowner to obtain any permits or to install a fence, if the pool wall height is 48” high or
higher. However, it is the homeowner’s responsibility to meet all applicable safety/health codes
and zoning regulations.
4. Unfold the Pool Liner and locate the reinforced holes closest to the GFI Outdoors Electrical
outlet.
5. Remove the metal structural parts from their boxes and place them around the outside of the
pool, making certain the top and bottom structure tubes (A & B) are arranged together. Also
place one (1) Upright Structure Tube (C) with every set of top and bottom tubes.
6. Slide the Top Structure (A) thru a slot opening in the white top rail membrane. Note that the
other end of the top structure should protrude from the next opening in the top rail membrane.
Install a second Top Structure (A) through the same opening that the previous end protrudes,
and slide it to the next opening. Continue inserting the Top Structure Pieces around the entire
pool top rail membrane.
7. Slide an Upright Structure Tube (C) onto the upright end of a Bottom Structure (B). Have a
helper hold this Upright Tube in a vertical position. Continue around the pool until all Bottom
Structures (B) are attached with the Upright Tubes (C). The Upright Tubes and Bottom
Structures are, now, self standing. (
Remember to disregard the color of the structure)

10
8. Have one person stand inside of the pool liner and lift the white membrane top rail (with the Top
Structure (A) inside). Arrange the protruding Top Structure ends to fit down into the nearest
vertical Upright Structure Tube (C). The person inside the pool should continue lifting the
adjacent Top Rail Membrane, as the outside person inserts each successive Top Structure end
down into the vertical Upright Structure Tube, until the Pool liner is completely attached to the
Vertical Supports. At this point, your Titan3 Round Pool is self-standing.
9. Open the bag of Clear Elastic PVC hose (D), and Connecting Pins (E). Distribute one of each at
every Upright Structure Tube around the pool. First insert Connection Pin (E) into one end of the
Hose. Thread the Hose through the attachment sleeve which is welded to the bottom side of the
liner, just behind the base of the Upright Structure Tube. Pull the PVC Tube until there is an
equal amount on each side. Holding the tubes together, thread them from the back to the front
between the Bottom Base Tubes (B), then separate the tubes and wrap each back around both
sides of the Bottom Tube/ Upright Structure, and attach together using the Connecting Pin.
Check to insure that most of the floor wrinkles are removed. This may require occasionally
pulling on the Elastic Hose during initial water fill to take out the wrinkles in the floor. After the
pool Is full of water, you may remove the Elastic Hose and store for future use.
10. Follow the ladder set up instructions and be sure to securely attach to the Titan3 Pool.

11
Care or your TitanPool3
1. Chemical Use-Consult with your pool chemical provider about the proper treatment of
your pool water. It is best to have your water tested, periodically, by a qualified Pool
chemical provider to determine what is required. Remember that over chlorination
of your pool will “Bleach Out” the liner, turning it white. This is not covered
under your warranty. If chlorine tablets are used, use proper dispenser. Do not place
chlorine tablets directly into the pool or skimmer. It is best to run your pump
whenever chlorine is being dispersed in the water.
2. The high quality membrane of your Titan3 is designed for long term performance. Be
aware that the Top Rail membrane may tend to accumulate dirt from time to time. It is
best to keep it clean by periodically cleaning it with a mild detergent. Be Careful not to
get the detergent into the pool water.
3. The blue walls of the Titan3 are quite glossy and may scratch if rubbed with an abrasive
surface or scraped, this should only be an appearance issue, and should not result in any
leakage. Additionally, due to the highly polished surface, dirt may stick from time to
time, but should wash off easily using a mild detergent and water.
Winterizing your TitanPool3
1. When winterizing your Titan3, it is recommended that winterization chemicals be
used to greatly improve the condition of your pool, when opening in the spring. Your
Titan3 Dealer should have these chemicals, but if not, other suppliers should be
available locally.
2. The Titan3 should be drained down to a level below the return eyeball fitting. Keep this
fitting open to help maintain water level throughout the winter.
3. Once proper depth has been reached, disconnect the entire Skimmer Assembly,
including the interior hoses, and remove from the pool. The Skimmer lower wall fitting
will need to be plugged from the inside of the pool.
4. Disconnect the exterior hoses from the Pool walls. Then drain your pump and filter and
follow manufacturers procedures for proper winterization of their equipment.
5. We recommend the use of a winter cover to help keep out leaves and other debris from
getting into the pool. A winter cover and cover pillow should be available from you local
Titan3 Dealer. Follow cover installation instructions included with winter cover. Attach
bungee cords to the pool legs.
6. DAMAGE TO THE POOL FROM ICE IS NOT COVERED UNDER THE WARRANTY.
Remember that the winter cover is NOT a safety Cover and will not prevent drowning.
Always remain diligent about children and non-swimmer adults around the pool with the
winter cover in place.

12
Your Titan3 Pool has been built to Splash’s rigorous specification and
crafted for your family’s enjoyment.
However!
REMEMBER THAT IT CAN ALSO BE DANGEROUS, IF NOT
ATTENDED TO PROPERLY .
BE SURE TO INSTALL ACCORDING TO ALL LOCAL AND STATE
BUILDING AND SAFETY CODES.
NEVER LEAVE CHILDREN UNATTENDED FOR ANY PERIOD OF TIME
WITHOUT A QUALIFIED ADULT PRESENT.
NEVER ALLOW ANY NON-SWIMMER IN THE POOL WITHOUT
PROPER FLOATION DEVICE OR QUALIFIED PERSON PRESENT.
IT IS RECOMMENDED TO NOT DRINK ALCOHOLIC BEVERAGES OR
INGEST OTHER REACTION IMPAIRMENT SUBSTANCES WHILE USING
THE POOL.
MAKE CERTAIN THAT ALL ELECTRICAL CONNECTIONS ARE GFI
PROTECTED.
DO NOT DISASSEMBLE SKIMMER EXCEPT TO CLEAN OUT THE
LEAF BASKET BY AN ADULT AND ONLY WITH THE PUMP IS OFF.
ALWAYS LOCK THE POOL ENTRY SYSTEM IN THE SAFE POSITION
WHEN NOT IN USE.
SHALLOW WATER-NEVER JUMP OR DIVE INTO THE POOL
THANK YOU FOR PURCHASING YOUR
TITANPOOl3
4.1.12

13
Box 4
This box should contain the following items:
A. Wall Fittings- qty 2 H. Floating Skimmer Weir
B. 3 m & 4 m Hose with 4 gaskets I. Skimmer Basket
C. 90 degree threaded elbow J. Skimmer Body w/hoses
D. Threaded Nipples- qty 2 K. Vacuum Adapter Plate
E. Ball Valve L. Eyeball for return fitting
F. Skimmer Hold Down fitting M. Patch Kit (glue & 2 membrane)
G. Threaded Wall Fitting Plugs - qty 2
Water Circulation System Plumbing
1. You received two (2) wall fittings (A) and one (1) Skimmer Hold Down Fitting (F). Note that all
three fittings have two (2) rubber gaskets and one (1) paper gasket. The rubber gaskets will always
be on either side of the pool membrane and the paper gasket will allow the fitting to be securely
tightened. One of these wall fittings should be used at the lowest hole in the corner. Insert the
threaded portion of the flanged end (with one rubber gasket) through the hole from the inside the

14
pool (NOTE: This is a good place to have one person on the inside of the pool to assist), then
screw the female threaded flanged nut on from the outside of the pool membrane (with the rubber
and paper gaskets). No Teflon tape or thread sealer is required.
2. The Skimmer Hold Down Fitting (F) should be installed through the upper hole in the corner of the
pool with the threaded portion with the nut end installed from inside the pool wall. Remember to put
one of the rubber gaskets on the threaded portion prior to sliding it through the hole. Then install the
other rubber gasket from the outside and then the paper gasket and then the cap (with the Splash
logo on it) should be tightened on to the fitting and secured tightly by hand.
3. On the end wall, locate the other hole for the return fitting. This wall fitting (A) is installed exactly
like the corner fitting for the skimmer. Install the threaded portion of the flanged end thru the wall
from the inside (remember the rubber gasket). Then install the rubber gasket and then the paper
gasket and thread on the tightening nut from the outside of the pool. No Teflon tape or sealer is
required. Hand tighten securely.
4. Attach Skimmer Body Hose (J) to the bottom pipe of the Skimmer Body (J) Note: soapy water will
help slide the hose on. Secure snuggly so that the treaded end is facing the bottom of the pool. Now,
screw this hose into the fitting (A) in the lower hole in the corner and tighten snuggly by hand (you
will need to us the Skimmer Body to rotate the hose”. Next, screw the short black hose on the side
of the Skimmer into the Hold Down Fitting (F). To help this process, the fitting on the end of the
hose will rotate to help screw into the Hold Down Fitting. Hand tighten. No Teflon tape is required.
5. Now insert the Skimmer Basket (I) into the Skimmer Body (J), with the open end up. Then slide the
Floating Skimmer Weir (H) down over the Skimmer Body (J). Note the Floating Weir inner
diameter is larger than the Skimmer Body outer diameter. NOTE: NOW would be a good time for
the person inside the pool to exit the pool!
6. From outside the pool, wrap Teflon Tape around threaded end of Ball Valve (E) that does not have
the union connection. Screw the Teflon Tape end into the bottom corner fitting on the pool and
secure by hand tightening. Do NOT put Teflon Tape on the threaded other end of the Ball Valve.
Now attach one of the furnished hoses (B) using the gasket provided to the Ball Valve (E) and run
the hose to the Suction side of the Pump/Filter System. Now, using one of the Threaded Nipples (D)
(notice the arrows on the side of the Nipple indicate which end is designed for connecting the hose)
the end NOT indicate for the hose should be threaded into the suction side of the Pump/Fiter system,
using Teflon Tape to secure the connection into the Suction side of the pump. Now Screw (don’t
forget to insert the gasket) the end of this first hose onto the open end of the Threaded Nipple (D).
No Teflon tape required.
7. Next, wrap Teflon tape around the end of the 90 degree Elbow (C) that is NOT indicated for the
Hose side (see markings on the elbow) and secure snuggly by hand. Thread the (gasketed) hose end
onto the “Hose Side” of the Elbow and secure by hand. The other end of this hose should run to the
discharge side of the Filter System. Again, Using Teflon Tape on the NON Hose side of the
Threaded Nipple, screw this end of the Nipple into the Filter Tank Outlet and tighten snuggly.
Attach the free end of the Hose (Remember the gasket) to this Threaded Nipple and secure snuggly.
8. Recheck all connections to assure they are tight and attach all Warning Labels.
9. Screw the EyeBall Fitting (L) into the side wall return Wall Fitting (A), you will probably want to
adjust the direction when the pump has water flowing into the pool
NOTE: Although there are no corners on the Round Pool, the orientation of the holes in the pool wall of
the Round Pool are the same as on the Rectangular Pool.
4.1.12

Titan3 Ladder
Assembly Instructions

SplashLadder Parts List
A.(2) Interior Step Rails
B.(3) Exterior Steps (Tabs)
C.(2) Interior Steps
D. (3) Platform Pieces
E.(3) Platform Step Supports
F. (2) Top Ladder Handles
G.(2) Vertical Supports (White)
H.(2) Exterior Step Rails (White)
I. (1) Metal Berth Pipe
J. (2) Step Stiffeners
K.(1) Plastic Strap (Spline)
L. (10) Metal Pins
M.(10) Plastic Plugs
N.(6) Metal Screws
O.(2) Long Metal Screws
P. (2) Metal “J” Hooks
Q.(1) Ladder Tool
R.(1) Warning Label
AB
C
DE
F
GH
I
J
R
K
G
F
2
M
P
NO
QL
©2003-Splash Superpools Ltd.

Step 1: Assembling the Ladder Top
1. Apply the Step Stiffener on the narrow end of one of the Platform Step Supports. 2. Insert the three Platform
Step Supports into the Ladder Platform piece with the Step Stiffener. 3. Insert the second Ladder Platform Piece
on top of the first and push down. 4. Place the second Step Stiffener on the Second Platform Piece. 5. Insert the
final Platform Piece and push down.
Step 2: Assembling the Waterside Steps
1. Apply the Plastic Plugs to the top holes of the two Interior Step Rails. 2. Begin sliding the first Interior Step
towards the bottom of the Interior Step Rails. 3. Now insert two Metal Pins into the Interior Step Rail’s holes. 4.
Push the Interior Step into place. Use the same procedure for the remaining Interior Step.
3©2003-Splash Superpools Ltd.
Parts Needed:
D. (3) Platform Pieces
E. (3) Platform Step Supports
J. (2) Step Stiffeners
J
DE
12345
Parts Needed:
A. (2) Interior Step Rails
C. (2) Interior Steps
L. (4) Metal Pins
M.(2) Plastic Plugs
24
M
C
A
LL
31

Step 3: Assembling the Outside Ladder Steps
1. Slide the first Exterior Step toward the bottom of the Exterior Step Rails (white). 2. Now insert two Metal Pins
intothe Exterior StepRails’holesand push the ExteriorStep downinto place. 3.Make sure the metalpinislocked
into place. 4. Put the four Plastic Plugs into the four holes on the Exterior Step Rails.
Step 4: Connecting the Ladder Top with the Ladder’s Waterside Steps
1. Insert the two Top Ladder Handles into the assembled Interior Step’s holes. 2. Insert theAssembled Platform,
lining up the holes for the Metal Screws. 3. Insert the Metal Screws, apply the Nuts and Washers and tighten with
the Ladder Tool. 4. The Interior Steps are now complete.
1234
4©2003-Splash Superpools Ltd.
Parts Needed:
Assembled Platform
Assembled Interior Steps
F. (2) Top Ladder Handles
N. (2) Metal Screws
N
F
Parts Needed:
B. (3) Exterior Steps (Tabs)
H. (2) Exterior Step Rails (White)
L. (6) Metal Pins
M.(4) Plastic Plugs
1234
B
H
L
M

Step 5: Connecting the Assembled
Ladder with the Outside Legs
1. Put the plastic plugs into the holes on the bottom of the curved ends of the Vertical Supports. 2. Insert the two
Vertical Supports into the Top Ladder Handles. (The curved Vertical Support ends should be facing the Interior
Steps.) 3. Line up the holes for the Metal Screws. 4. Using the Ladder Tool, tighten the Metal Screws with the
corresponding Nuts and Washers. 5. The outside Vertical Supports are now attached.
1234
5
Step 6: Connecting the Assembled Ladders
1. Place the SplashLadder’s Exterior Steps on the outside of the Vertical Supports. (Be sure the Exterior Steps
slope down and away from the pool.) 2. Line up the holes of the Platform piece and the Exterior Steps for the
Metal Screws. 3. Using the Ladder Tool, tighten the Metal Screws with the corresponding Nuts and Washers.
4. The SplashLadder assembly is now complete. 5©2003-Splash Superpools Ltd.
Parts Needed:
Assembled Inside Steps
Assembled Outside Steps
N. (2) Metal Screws
1234
N
Parts Needed:
Assembled Interior Steps
G. (2) Vertical Supports
M.(2) Plastic Plugs
N. (2) Metal Screws with Nuts and Washers
M
NG

Pleasenote:If you havepurchasedaround pool,pleaserefer to thelastpageofthemanual fortheround ladder
“Horseshoe” Berth Pipe installation instructions.
Step 7: Attaching the Berth Pipe to the SplashLadder
Step 8: Attaching the SplashLadder with the
Berth Pipe to the Buttress Leg of the Pool
1. Remove release paper from back of Long Foam Strip (T), and install Foam Strip onto the under-
side of the Ladder top platform. 2. Select a desired Buttress Leg on a straight side of the pool for
the SplashLadder. Set Ladder onto top rail of the Splash Pool so that waterside steps are in the
water and the top platform Foam Strip is resting on the top rail. 3. Attach the Berth Pipe to the
Buttress Leg with the two Metal “J” Hooks (P) from inside the Buttress Leg. 4. Place the large
washeron the threaded end ofthe “J” Hooks thatextend through the Berth Pipe. 5.Tighten the “J”
Hooks to the Berth Pipe with the corresponding nuts. (A wrench will be required for this step). 6.
Tighten the long screws on the Berth Pipe and Bottom Ladder Supports. Screw the Round Plastic
Caps (S) onto the exposed thread of the “J” Hooks. Your Splash Ladder is now secure.
6
1. Insert Metal Nut into hex shaped recess in Square Plastic Plug (M-1), repeat with second Plug. 2. Insert Square
Plastic Plug (M-1) (with nut installed) into the end of Berth Pipe, making certain to align the nut with the small hole in
the Berth Pipe. Repeat at other end. 3. Line up one nut hole in Berth Pipe with hole in Bottom Ladder Support.
4. Insert a Long Metal Screw, with washer, through hole in Bottom Ladder Support and screw into Berth Pipe.
Repeat at other end of Berth Pipe. Do not over tighten, leaving some slack. 5. Insert Round Plastic Caps (M-2) in
ends of Bottom Ladder Support.
12345
6
©2003-Splash Superpools Ltd.
Parts Needed:
I. (1) Berth Pipe
M-1. (2) Square Plastic Plugs with Nut Slot
M-2. (2) Round Plastic Plugs
O. (2) Long Metal Screws with Nuts and Washers
I
O
M-1
M-2
Parts Needed:
P. (2) Metal “J” Hooks with large Washers and Nuts
S.(2) Round Plastic Caps
T. (1) Long Foam Strip
23451
P
TS