SSV Works RKR-2K User manual

1
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty
against defects in material or workmanship. All Kicker Speakers are covered by a limited 1
year warranty against defects in material or workmanship. All Kicker Ampliers are covered by
a limited 2 year warranty against defects in material or workmanship. Labor for replacement
of defective components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
- Panel Removal Tool - 10mm wrench
PARTS LIST IMAGES
2. MRB3 Brain and Tray
5. Grommet
9. #4 Coarse Threaded Screw x2
6. M6x1.0x16mm 5mm Allen
Head Screws x4
10. M3x0.5x8mm Machine
Screw x2
7. Push Pins x4
11. Zip Ties
8. M6x1.0x12mm T30 Torx
Screws & Washers x4
1. RKR-2K 4. Center Cover3. Mounting Brackets
- 5mm allen key
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] | Fax: [phone]
RKR-2K
Can-Am Ryker 2-Speaker Audio Kit
- T20, T30 torx - #1 phillips screwdriver - Drill & 1/8” 5/16” drill bits - Scribe or marker

2
A
F
D
E
B
C
A. Compress the locking tabs to the hood and slide the hood down
simultaneously to release the hood and remove.
B. Use a 10mm socket to disconnect the negative battery terminal.
C. Open the front storage compartment, remove the (4) push pins and
(2) T20 Torx screws.
F. Using a panel tool, release the clips for the trim panel from the
storage compartment.
D. Slide back the fuel door. Remove the (4) push pins that are now
exposed.
E. Pull the driver and passenger side panels off the Ryker.
COMPRESS

3
K
G H
HJ
I. Align the RKR-2K over the mounting bases. Fasten the RKR-2K to the
mounting brackets with the provided (4) M6x1.0x12mm torx screws and
(4) M6 washers using a T30 Torx driver.
K. Place the USB charging port into the front of the MRB3 mounting plate
and refasten the nut.
G. Once the fairing panel has been released, lift the front storage
compartment and disconnect the USB charging port. Set the
compartment aside for future steps.
H. Fasten the RKR-2K mounting brackets to the front of the gauge cluster
mount. With (2) 5mm allen screws on each side. Note the orientation of
the mounting bases.
J. Unscrew the nut from the USB charging port and remove the
charging port.
L
L. Seat the MRB3 brain assembly into the storage container. Verify that it
is not pinching any of its harness’. MRB3 brain will make contact with
the top of the compartment. Mark with a scribe or permanent marker
the mounting points of the MRB3 bracket.

4
M
O
Q
N
P
R
M. Remove the MRB3 brain assembly from the storage container and
drill a pilot hole with a 1/8” drill bit at each marked point. Open up
each pilot hole with a 5/16” drill bit.
O. Tuck the harness from the RKR-2K with the factory harnesses in the
faring panel.
Q. Seat the cable grommet into the former location of the factory USB
port.
N. To route the harness from the RKR-2K to the MRB3 brain, pull the harnesses
from the RKR-2K back around the upper fairing panel and to the front of the
fairing panel. We recommend turning your handlebars to the right to allow
for the most clearance for routing the cables.
P. Connect the RKR-2K spade connectors to the factory power and
ground that were disconnected from the factory USB port in Step G.
R. Route the RKR-2K cables into the storage compartment through
the grommet.

5
U
W
N T
V
X
S. Connect the factory USB port to the power ground. Reference the back of
the USB port to identify which terminal is power or ground.
U. Connect the MRB3 front speaker output to the RKR-2K input.
W. Connect the MRB3 power connector to the RKR-2K power output.
T. Connect the antenna.
V. Align the arrows on the wire control panel with the arrow on the
MRB3 controller connector and connect.
X. Place the now connected MRB3 brain in its mounting position over
the holes drilled in Step L.

6
Y
A1
Z
B1
Y. From the exterior of the storage compartment, place (2) push pins on
each side to mount the MRB3 in place.
A1. Hold the center cover onto the front of the RKR-2K, fasten the (2) M3
machine screws into the system to retain the cover.
Z. Place the storage compartment back into its cavity.
B1. Support the top of the center cover of the system and fasten the
(2) #4 coarse threaded screws to into the unit to complete cover
installation. Test the system prior to reassembly of the vehicle.
© 2019 SSV Works, Oxnard, CA 93030 RKR-2K Rev. A 11-19-19