ST VIP-M07SPI-ADIS User manual
October 2017 DocID030800 Rev 1 1/15
1
UM2251
User manual
VIP-M07SPI-ADIS
Introduction
This document describes the specifications for the 12 V M0-7 SPI discovery board that is
able to work connected to SPC560B-DIS discovery board to create a solution for a specific
12 V BCM (Body Control Module) system.
In a typical car body application it is necessary to connect a microcontroller to drive several
loads (bulb lamps, led lamps, electrical motors and so on). When using a bulb lamp, to
increase its lifetime and avoid flickering, it is necessary to shift PWM signals and adapt the
duty cycle to battery life.
The M0-7 SPI expansion board provides diagnostics feedback and current consumptions to
operating close loop for each single load synchronized with the PWM signals. SPC560B-
DIS is the core hardware to generate shifted PWM signals and synchronize ADC
conversion.
www.st.com
Contents UM2251
2/15 DocID030800 Rev 1
Contents
1 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Hardware, schematic and layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 M07 SPI devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5 Extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Graphical User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DocID030800 Rev 1 3/15
UM2251 List of tables
3
List of tables
Table 1. Loads configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 2. Extension connectors pins used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 3. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
List of figures UM2251
4/15 DocID030800 Rev 1
List of figures
Figure 1. VIP-M07SPI-ADIS schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 2. VIP-M07SPI-ADIS Top layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 3. VIP-M07SPI-ADIS Bottom layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DocID030800 Rev 1 5/15
UM2251 Quick start
13
1 Quick start
VIP-M07SPI-ADIS is an easy-to-use board offered at budget price. Together with a
dedicated GUI and firmware (STSW-M07SPI-ADIS) and in combination with SPC560B-DIS
board, it becomes a tool to evaluate M0-7 SPI high-side drivers.
1.1 Getting started
Follow the sequence below to configure the system and launch the application:
1. Check jumper position in the SPC560B-DIS board:
J14,J13,J12,J7J6,J2,J11 removed
S1,S2,J10,J9,J2,J1,J3 inserted
2. Connect the SPC560B-DIS board to a PC with a USB cable ‘type A to mini-B’
3. Download firmware STSW-M07SPI-ADIS and program board as described on
www.st.com
4. Disconnect USB cable
5. Plug VIP-M07SPI-ADIS board and connect 12V power supply on J18
6. Install GUI on your PC as described on www.st.com
7. Connect loads to the outputs
8. Check jumper position in the VIP-M07SPI-ADIS:
JP1 closed
9. Connect USB cable to PC
10. Execute GUI (www.st.com)
Hardware, schematic and layout UM2251
6/15 DocID030800 Rev 1
2 Hardware, schematic and layout
Figure 1. VIP-M07SPI-ADIS schematic
*1'
9EDW
&
Q)
*1'
5 .
5 .
*1'
-
-
'
%$6
5 5
/('
*1'
9EDW
5
.
5 .
5 .
-
-
&
Q)
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
6',
&61
*1'
6&.
9''
95(*
6'2
*1'
&B6(16(
,1
,1
9&&
,1
,1
*1'
287387
287387
287387
8
9136<
&
Q)
,1B
,1B
,1B
,1B
,1B
,1B
,1B
,1B
9''B&21752//+20(B
/+20(B
6',
6',
6'2
6'2
6&.
6&.
&6B
0XOWLVHQVH
0XOWLVHQVH
9287B
9EDWB$'
9EDWB$'
/+20(B
2XWB
2XWB
2XWB
2XWB
9287B9287B
9287B
4
%66
9
9''B&21752/
5
.
/('
5
. *1'
9''BRXW
9''BRXW
0XOWLVHQV H
&6B
2XWB
2XWB
2XWB
2XWB
5 5
/('
*1'
/+20(B
-
5.
5
.
/('
*1'*1'
&Q)
&
Q)
*1'
&Q)
&Q)
5.
*1'
5.
*1'
9287B
2XWB
2XWB
2XWB
2XWB
9287B
9287B
9287B
5
5
*1'
5 .
5 .
5 5
5 .
-3
9GG
5 5
-
-
-
-
*1'
*1' 73 WR EH SODFH G VRPHZKHUH LQ WKH 3&%
*1'B3527B
5
.
5
.
5
5
*1'
5
.
5
5
*1'
5
.
5
5
*1'
5
.
5
5
*1'
-
-
9EDW
/('
/('
/('
&6B
-
-
5
. /('
*1'
&Q)
9287B
5
.
5
5
*1'
2XWB
2XWB
9287B
9287B
9287B9287B
9287B
9EDW
&
Q)
*1'
&
Q)
&
Q)0XOWLVHQV H 2XWB
2XWB
2XWB
9''BRXW
5.
5.
*1' *1'
&Q)
&
Q)
*1'
&
Q)
&Q)
5.
*1'
5.
*1'
6',
6'2
6&.
5 5
5 .
5 .
5 .
*1'B3527B
5
.
5 .
5 .
5 .
5 .
5
.
/('
/('
/('
/('
'
%$6
&6B
-
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
287387
6',
&61
*1'
6&.
9''
95(*
6'2
*1'
&B6(16(
,1
,1
9&&
,1
,1
*1'
287387
287387
287387
8
9146<
2XWB
5
.
5
5
*1'
9287B
5
.
5
5
*1'
9287B
5
.
5
5
*1'
9287B
5
.
5
5
*1'
9287B
'LVFRYH U\ &RQQH FW RUV
;
;
;
;
9 9
9EDW
8$57B5;8$57B7;
-3
-3
*3,2
*3,2
*3,2
9
8$57B7;
8$57B5;
*3,2'
*3,2&
*3,2%
*3,2$
%OXHWRRWK 0RGXOH
*3,2
*3,2*3,2
*3,2'
*3,2&
*3,2%*3,2$
*1'
*1'
*1'
*1' *1'
*1'
*1'
*1'
*1'
*1'
*1'
*1' *1'
*1'
*1'
*1'
*1' *1'
5 5 5 5
*1'
'=
""""
'=
""""
-
-
-
-
,1B
,1B
,1B
,1B
,1B
,1B
,1B
,1B
5
WEG
&VHQV H
S)
5
.
*1'
'
%$7<
*1'
5 .
5
WEG
&VHQV H
S)
*1'
*1'
5 .
)
)
)
)
Hardware, schematic and layout UM2251
8/15 DocID030800 Rev 1
Figure 3. VIP-M07SPI-ADIS Bottom layer
2.1 M07 SPI devices
These devices are manufactured using ST proprietary VIPower M0-7 technology and are
designed to drive 12V automotive grounded loads through a 3V and 5V CMOS-compatible
interface, providing protection and 16-bit ST-SPI for full diagnostic with 8 bits Short Frame
option.
The device integrates advanced protective functions and a dedicated multifunction
multiplexed analog output pin delivers sophisticated diagnostic functions including high
precision proportional load current sense, in addition to the detection of overload and short
circuit to ground, short to VCC and off-state open-load.
DocID030800 Rev 1 9/15
UM2251 Hardware, schematic and layout
13
Following a short description of the most important features of M07 devices:
General
– 16-bit ST-SPI for full diagnostic with 8 bits Short Frame option
– Programmable Bulb/LED mode
– Advanced limp home functionalities for robust fail-safe system
– Very low standby current
– Optimized electromagnetic emissions
– Very low electromagnetic susceptibility
– Control through direct inputs and / or SPI
– Compliant with European directive 2002/95/EC
Diagnostic functionalities
– Multiplex proportional load current sense
– Synchronous diagnostic of over load and short to GND, output shorted to VCC and
OFF-state open-load
– Programmable case overtemperature warning
Protections
– Two levels load current limitation
– Self limiting of fast thermal transients
– Undervoltage shutdown
– Overvoltage clamp
– Latch-off or programmable time limited auto restart (power limitation and
overtemperature shutdown)
– Load dump protected
– Protection against loss of ground
The M07 discovery board is equipped with 2 M07 SPI high side drivers:
U1 is a VNQ7003SY a quad channels in PowerSSO-36 package with channels 0-1 25mΩof
RON and channels 2-3 7mΩof RON
U2 is a VNP7008SY a penta channels in PowerSSO-36 package with channels 0-4 40mΩof
RON
The suggested configuration to drive front corner and a rear corner is illustrated in Table 1:
Table 1. Loads configuration
Light Load (W) Part number Device Channel
Front corner
Position W5W/H7 VNQ7003SY U1 1
Low Beam H3/H15 VNQ7003SY U1 2
High Beam H7 VNQ7003SY U1 3
Fog 21W VNQ7003SY U1 0
Hardware, schematic and layout UM2251
10/15 DocID030800 Rev 1
2.2 Power supply
The power supply is provided through J18 connectors and must be able to provide the
current requested by all the loads connected.
2.3 LEDs
LEDx: indicates the status of the correspondent outputx
2.4 Jumpers
J1 powers the digital control and SPI interface
2.5 Extension connectors
The male headers X1,X2,X3 and X4 are two strip lines connectors of 2x36 each and are
used to allow the access to all the Bolero’s pins with exception of JTAG, TCK, TMS, TDI,
TDO, XTAL, EXTAL and VDD_LV. The pins used in this M07 SPI applications are the
following:
Rear corner
Position W5W/H7 VNP7008SY U2 0
Stop 21W VNP7008SY U2 1
Reverse 21W VNP7008SY U2 2
Fog 21W VNP7008SY U2 3
Turn W16W VNP7008SY U2 4
Table 1. Loads configuration (continued)
Light Load (W) Part number Device Channel
Table 2. Extension connectors pins used
Discovery
Connector X1
ASD_M07SPI_
ADIS
Discovery
Connector X2
ASD_M07SPI_
ADIS
Discovery
Connector X3
ASD_M07SPI_
ADIS
Discovery
Connector X4
ASD_M07SPI_
ADIS
1GND 1 GND 1Batt 1Batt
2 PE[2] 2 PE[3] 2 GND 2 GND
3PC[5]
(CSN)
GPIO3 3 PC[4] GPIO2 3 TCK 3 TDI
4 PE[4] 4 PE[5] 4 TDO 4 TMS IN0_2
5 PH[4] 5 PH[5] 5 PA[6] LHOME_
1
5 PA[5] VDD_CO
NTROL
DocID030800 Rev 1 11/15
UM2251 Hardware, schematic and layout
13
6 PH[6] 6 PH[7] 6 PC[2] GPIO1 6 PC[3]
7 PH[8] 7 PE[6] 7 PG[1
1]
7PG[10]
8 PE[7] 8 PC[12] 8 PE[1
5]
8 PE[14]
9 PC[13] 9 PB[1]
(RxDC)
9PG[1
5]
9PG[14]
10 PB[2] UART_T
X
10 PB[3] UART_
RX
10 PE[1
2]
10 PA[11] IN3_2
11 GND 11 GND 11 GND 11 GND
12 PB[0]
(TxDC)
12 PC[14] 12 PA[10
]
VOUT4_1 12 PA[9] IN2_2
13 PC[15] 13 PG[5] 13 PA[8] IN1_2 13 PA[7] LHOME_2
14 PG[4] 14 PG[3] 14 PE[1
3]
14 PF[14]
15 PG[2] 15 PA[2] IN1_1 15 PF[15
]
15 PG[0]
16 PE[0] 16 PA[1] IN0_1 16 PG[1] 16 PH[3]
17 PE[1] 17 PE[8] 17 PH[2] 17 PH[1]
18 PE[9] 18 PE[10] 18 PH[0] 18 PG[12]
19 PA[0] 19 PE[11] 19 PG[1
3]
19 PA[3] IN2_1
20 RESET_
ASD
20 PG[9] 20 PB[1
5]
20 PD[15]
21 PG[8] 21 PC[11] GPIOD 21 PB[1
4]
21 PD[14]
22 GND 22 GND 22 GND 22 GND
23 PC[10] 23 PG[7] 23 PB[1
3]
Vbat_A/D 23 PD[13]
24 PG[6] 24 PC[9] 24 PB[1
2]
CS_2 24 PD[12]
25 PC[8] GPIOC 25 PF[9] 25 PB[11
]
25 PD[11]
Table 2. Extension connectors pins used (continued)
Discovery
Connector X1
ASD_M07SPI_
ADIS
Discovery
Connector X2
ASD_M07SPI_
ADIS
Discovery
Connector X3
ASD_M07SPI_
ADIS
Discovery
Connector X4
ASD_M07SPI_
ADIS
Hardware, schematic and layout UM2251
12/15 DocID030800 Rev 1
26 PF[8] 26 PF[12] 26 PD[1
0]
26 PD[9]
27 PC[6]
(TxDL)
GPIOA 27 PC[7]
(RxDL)
GPIOB 27 PB[7] 27 PB[6]
28 PF[10] 28 PF[11] 28 PB[5] Multisens
e 2
28 PB[4] Multisens
e1
29 PA[15] CS_0 29 PF[13] 29 PD[8] 29 PD[7] VOUT3_2
30 PA[14]
(CLK)
SCK 30 PA[4] IN3_1 30 PD[6] VOUT2_2
30 PD[5] VOUT1_2
31 PA[12]
(MISO)
SDO 31 PA[13]
(MOSI)
SDI 31 PD[4] VOUT0_2
31 PD[3] VOUT3_1
32 PB[9] 32 PB[8] 32 PD[2] VOUT2_1
32 PD[1] VOUT1_1
33 PB[10] 33 PF[0] 33 PD[0] VOUT0_1
33 PF[7]
34 PF[1] 34 PF[2] 34 PF[6] 34 PF[5]
35 GND 35 GND 35 PF[4] 35 PF[3]
36 5V 36 5V 36 GND 36 GND
Table 2. Extension connectors pins used (continued)
Discovery
Connector X1
ASD_M07SPI_
ADIS
Discovery
Connector X2
ASD_M07SPI_
ADIS
Discovery
Connector X3
ASD_M07SPI_
ADIS
Discovery
Connector X4
ASD_M07SPI_
ADIS
DocID030800 Rev 1 15/15
UM2251
15
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
Table of contents
Other ST Microcontroller manuals
ST
ST STM32F410 User manual
ST
ST STEVAL-MKSBOX1V1 User manual
ST
ST STM32L0x3 User manual
ST
ST STM32F7508-DK Manual
ST
ST STM8L-DISCOVERY User manual
ST
ST X-NUCLEO-53L4A1 User manual
ST
ST STM8AF Series User manual
ST
ST STM32F207 series User manual
ST
ST ST25R3911B-DISCO User manual
ST
ST AN3154 Installation and operating instructions
ST
ST STM32H745I-DISCO User manual
ST
ST STEVAL-MKBOXPRO User manual
ST
ST SimpleMAC STM32W108 Series User manual
ST
ST STM32H5 Nucleo-144 User manual
ST
ST STM8A-DISCOVERY User manual
ST
ST STM32 Nucleo User manual
ST
ST UM0250 User manual
ST
ST STM32F7308-DK User manual
ST
ST SPC582B Series Installation and operating instructions
ST
ST STM32G4 Series User manual
Popular Microcontroller manuals by other brands
ELECRAFT
ELECRAFT K3 Installing
Starbox
Starbox GM-14915052 quick start guide
Nuvoton
Nuvoton NuMicro M032 Series user manual
Freescale Semiconductor
Freescale Semiconductor FRDM-KL82Z user guide
Freescale Semiconductor
Freescale Semiconductor MK22FN256VDC12 Reference manual
Renesas
Renesas V850ES/Fx3 Series user manual
NXP Semiconductors
NXP Semiconductors S12 MagniV MC9S12ZVML128 quick start guide
Texas Instruments
Texas Instruments LAUNCHXL-CC1310 Wiring diagrams
NEC
NEC 78K0S/K 1+ Series Application note
HANHAA
HANHAA Symbisa HY-000003 user manual
NEC
NEC 78K0S/K 1+ Series Application note
Atmel
Atmel QTouch Application note