Stagg SLI FLATSET1 User manual

!
User Manual
FLATSET
SLI-FLATSET1

!
Unpacking: Thank you for purchasing this product. Every model has been
thoroughly tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during shipping.
If the packaging appears to be damaged, carefully inspect your product for any
damage and be sure all equipment necessary to operate the unit has arrived
intact.
Introduction: The SLI FLATSET1 is a five or fourteen-channel set. It can be
operated in three different modes; DMX control, sound activation or
master/slave. The SLI FLATSET1 comes with several built-in programs.
For best results use fog or special effects smoke to enhance the beams
projections.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose
this unit to rain or moisture.
Warning! Avoid looking directly into the light source at all times! This may
cause severe eye damage.
Features
• RGB Colour Mixing
• Colour Strobe Effect
• Colour Mix Effect
• LED Chases (Adjustable Speeds)
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 Protocol
• 3 Operating Modes -Sound Active, Master/Slave Mode and DMX Control
•Digital Display for Address and Function Setting
•Each fixture can be operated independently

!
On Board System Menu
The SLI FLATSET1 comes with an easy to navigate system menu. This section
will detail the functions of each command in the system menu. Please read this
section thoroughly!
To access the main menu press the ESC button. Press the UP or DOWN button
until you reach the function you wish to change. When you reach the function
you wish to change press the ENTER button. When a function is selected, use
the UP or Down button to change the function settings. Once your changes are
made, press the ENTER button.
Addr - DMX Address Setting via
control board
1. Press the ESC button and UP
or DOWN button until “Addr” is
displayed, then press ENTER.
2. “Axxx” will now be displayed,
“x” representing the displayed
address. Press the UP or DOWN
button to find your desired
address.
Auto -This menu will let you
select your desired auto mode
1. Press the ESC button and UP
button or DOWN button until
“Auto” is displayed, then press
ENTER.
2. “Autx” will now be displayed.
You can confirm auto mode by
pressing UP or DOWN.

!
ChAS -This menu will let you select your desired chase mode
1. Press the ESC button and UP button or DOWN button until “ChAS” is
displayed, then press ENTER.
2. “C x” will now be displayed. You can confirm chase modes by pressing UP or
DOWN.
3. Then press ENTER; “sp x” will be displayed , “x” representing a number
between 1-9. Press the UP or DOWN button to set the chase speed.
Colo -This menu will let you select your desired colour mode
1. Press the ESC button and UP or DOWN button until “CoLo” is displayed, then
press ENTER.
2. Either “CoL X” (“X” representing a number between 1-9), or “AtF ” will be
displayed. Press the UP or DOWN button to select either a static colour or “AtF ”
mode. If you select “AtF , and press ENTER, it will set the Red brightness, the
green brightness and the blue brightness.
Chnd -This menu will let you select your desired DMX Channel mode
1. Press the ESC button and UP button DOWN button until “Chnd” is displayed,
then press ENTER.
2. “X Ch” will now be displayed, “X” representing the displayed DMX channel
mode. Press the UP or DOWN button to find your desired Channel mode.
SLav-This menu will let you select your desired Master/Slave mode
1. Press the MENU button until “SLav” is displayed, press ENTER.
VER -This will display the software version
1. Press the MENU button until “VER” is displayed. Press the ENTER button and
the software version will be displayed.

!
Foot controller System Menu
The SLI FLATSET1 comes with an easy to navigate system menu for foot
controller. This section will detail the functions of each command in the system
menu. Please read this section thoroughly!
To access the auto mode press the “AUTO” button. Press the “SOUND” button to
set your sound mode function. Press the COLOUR button to set your function for
colour mode. Press the BLACKOUT button if the LED is unlit, and then press it
once more; the fixture will run;
DMX control mode
This function will allow you to control each individual fixtures trait with a standard
DMX-512 controller.
Universal DMX Control: This function allows you to use a universal DMX-512
controller to control head movement. A DMX controller allows you to create
unique programs tailored to your individual needs.
1. The SLI FLATSET1 uses two DMX channel modes. See below for detailed
description of the DMX traits.
2. This will allow you to create your own programs.
BUT T ON FUNCTION
AUTO Press it to auto mode,then press to change auto mode
SOUND Press it to sound mode,then press to change sound mode
COLOR Press it to color mode,then press to change color mode
BLACKOUT Press it all LED dark,then press to restore the current state

!
DMX value and function (five-channel mode)
channel function
Ch1 red (0%--100%)
Ch2 green (0%--100%)
Ch3 blue (0%--100%)
Ch4 speed (slow to fast)
nop
chase1
chase2
chase3
chase4
chase5
auto 1
auto 2
auto 3
auto 4
auto 5
auto 6
auto 7
auto 8
auto 9
auto 10
auto 11
auto 12
auto 13
auto 14
sound 1
sound 2
value
Ch5
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 11
12 …… 23
24 …… 35
36 …… 47
48 …… 59
60 …… 71
72 …… 83
84 …… 95
96 …… 107
108 …… 119
120 …… 131
132 …… 143
144 …… 155
156 …… 167
168 …… 179
180 …… 191
192 …… 203
204 …… 215
216 …… 227
228 …… 239
240 …… 251
252 …… 255

!
DMX value and function (fourteen-channel mode)
Note: The LED may flash when the
function speed value is between 8 and 255.
Model: SLI FLATSET1
Voltage: 100~240V/ 50~60Hz
Power Consumption: 176W
LED Qty : 4 X 7 3W (3 in 1) LEDs
Weight : 13.5kg
Fuse : 3A (250V)
DMX : 5 channels/14 channels
Sound Active : Yes
channel function
Ch1 pot1 red (0%--100%)
Ch2 pot1 green (0%--100%)
Ch3 pot1 blue (0%--100%)
Ch4 pot2 red (0%--100%)
Ch5 pot2 green (0%--100%)
Ch6 pot2 blue (0%--100%)
Ch7 pot3 red (0%--100%)
Ch8 pot3 green (0%--100%)
Ch9 pot3 blue (0%--100%)
Ch10 pot4 red (0%--100%)
Ch11 pot4 green (0%--100%)
Ch12 pot4 blue (0%--100%)
Ch13 speed (slow to fast)
nop
chase1
chase2
chase3
chase4
chase5
auto 1
auto 2
auto 3
auto 4
auto 5
auto 6
auto 7
auto 8
auto 9
auto 10
auto 11
auto 12
auto 13
auto 14
sound 1
sound 2
value
Ch14
0 …… 11
12 …… 23
24 …… 35
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255
36 …… 47
48 …… 59
60 …… 71
72 …… 83
84 …… 95
96 …… 107
108 …… 119
120 …… 131
132 …… 143
144 …… 155
156 …… 167
168 …… 179
180 …… 191
192 …… 203
204 …… 215
216 …… 227
228 …… 239
240 …… 251
252 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255
0 …… 255

!
!
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS.
• If, after you have followed the instructions outlined above, this device fails to function, please
contact your dealer. Under no circumstances should this device be opened. Leave all servicing to
qualified personnel.
•Electrical appliances must never be used in conditions of high humidity or heat. To prevent any risk
of fire or electric shock, never spill or splash liquids on this device. Should this happen, unplug the
power cable from the mains outlet and switch off the mixer immediately.
MARKING & CONFORMITY
1. The CE mark on this product means it conforms to the EMC Directive (2004/108/CE), CE marking
Directive (93/68/EEC) and Low Voltage Directive (2006/95/EC).
2. The «Crossed-out Wheeled Bin» is to draw your attention to the WEEE (Waste Electric &
Electronic Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately
for recycling.
3. «RoHS compliant» means this device conforms to the Directive (2002/95EC) on the restriction of
the use of certain hazardous substances in electrical and electronic equipments, such as: Mercury,
Lead, Cadmium, Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated
Diphenyl Ethers (PBDE).