Larson Electronics HALSS-24-2L-LED-HBL User manual

HALSS-24-2L-LED-HBL
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
2' Stainless Steel Hazardous Location LED Light Fixture
Heat Treated Glass Lens - Class I, Div. II Instruction Manual
Thank you for your purchase of the Larson Electronics HALSS-24-2L-LED-HBL.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE HALSS-24-2L-LED-HBL MUST BE WIRED
IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL
CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION
SHEET, CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
The Larson Electronics HALSS-24-2L-LED-HBL Hazardous Area LED Light Fixture is ETL approved Class 1 Division 2
Groups A, B, C and D - 1598A listed and is specifically designed to withstand high vibration locations and the rigors of wet
and corrosive marine environments.

HALSS-24-2L-LED-HBL
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2 of 2
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage alicensed electrician install this product,in all locations especially in outdoor
areas where weatherproofing may be required. Universal voltage driver permits operation at 120V - 277V AC, 50 or 60Hz,
except those factory ordered at low voltage 12-24 Volts DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown in the
diagram 
Secure each pair of wires according to the diagram. Utilize ajunction box
or similar device and take precautionary steps for weatherproofing
all connectionsif installed in alocation where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to all local
and national electrical/building codes.
STANDARD FLANGE BRACKET MOUNTING
Stainless steel bracket mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide
flexibility in setting the angle of the fixture. Three through holes provide sufficient mounting for any environment.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing maintenance.
Warning: Risk of electric shock.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine checks to be made on a yearly
basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow an Electrical Preventive
Maintenance Program as described in NFPA 70B: Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance. Clean the lens with a damp,
non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e.excessivedust
build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment. Always
check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of children when not in use.
Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The HALSS-24-2L-LED-HBL is designed to provide years of reliable performance. Should the need for replacement parts arise, please
contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Low Voltage DC
Connect power to power supply outputting low voltage between 12-24 Volts DC. This variable voltage allows greater
versatility without affecting light output. Ensure deutsch connectors are properly connected (If applicable)