Stagg TAGGER 60 User manual

USER MANUAL
TAGGER 60
SLI-MHBTAGG60
Please read the instructions carefully before use

!
SAFETY INSTRUCTIONS
Please read the instructions carefully as they include important
information about the installation, operation and maintenance.
• Please keep this user’s guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
• All fixtures leave the manufacturer intact. Please note that any damages incurred
by the user is not covered by the guarantee.
• Unpack and check carefully that there is no transportation damage before using the
unit.
• The unit is for indoor use only. Use only in a dry location.
• Use a safety bond when attaching the fixture to a lighting rig. Handle by the
hanging bracket when fixing.
• The unit must be installed in a location with adequate ventilation at least 50 cm
from adjacent surfaces.
• Make sure that no ventilation slot is blocked, otherwise the unit will overheat.
• Before operating, ensure that the voltage and frequency of the power supply match
the power requirements of the unit.
• Make sure all equipment is properly earthed.
• Do not operate the unit if the ambient temperature is higher than 40°C.
• Do not hardwire to any mains dimmer.
• On the first start, there may be some normal operational start-up smell.
• Make sure that there is no flammable material close to the unit while operating, as
it is a fire hazard.
• Examine power wires carefully and replace immediately if there is any damage.
• Never run on for a long time lest shortening lifespan. Avoid any inflammable liquids,
water or metal objects entering the unit. In case it happens, cut off the mains power
immediately.

• Do not operate in a dirty or dusty environment. Clean fixtures regularly.
• Do not allow children unsupervised to operate the fixture.
• Do not touch any wire during operation as there might be a hazard of electric
shock.
• Avoid placing power wires next to other cables.
• Disconnect the mains power before replacing or servicing the fuses.
• Replace fuse only with the same type.
• In the event of a serious operating problem, stop using the unit immediately.
• Never turn on and off the unit time after time.
• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
• Do not open the unit as there is no user serviceable part inside.
• Never try to repair the unit by yourself. Repairs carried out by unskilled people can
lead to damage or malfunction. Please contact the nearest authorized technical
assistance centre.
• Disconnect the mains power if the fixture is not used for a long time.
• Use the original packaging to transport regarding any warranty issue.
• Do not look directly at the LED light beam while the fixture is on.
• Do not connect more than 7 units to the same power source.

INSTALLATION
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that
the structure to which you are attaching the unit is secure and able to support 10 times
the unit’s weight. Also, always use a safety cable that can hold 12 times the unit’s
weight when installing the fixture.
The equipment must be fixed in an appropriate place by professionals. Keep it out of
the reach of unqualified people.
TECHNICAL SPECIFICATIONS
Gobo moving head with 60-watt COB LED 7 colours,7 gobos.
- LED: 60W white LED
- 540° pan, 230° tilt
-Beam angle: 13°
- Colour wheel: 7 colours + white
- 7 fixed gobo's + open with shake
- Manual focus
- protocol: DMX-512 : 9 or 11 Channels
- Strobe: 0-10Hz
- Control Modes: DMX, automatic, sound mode or Manual Setup
- Display: 4 Digit
- DMX input & output: 3-pin XLR connectors
- Power input: IEC
-Included: Hanging bracket (truss- or other clamp not included)
- Power consumption: 70w (max)
- For indoor use only
- Weight: 3kg (6.6lb)
- Size: 290 x 260 x 210 mm (11.4 x 10,2 x 8.3“)

SETTING UP THE DEVICE

DMX Mode
With the menu button, select the DMX mode (ADDR) and press the enter key to
confirm. Then use the up and down buttons to choose the desired DMX channel (1 –
512) and press the enter key to confirm. Press the menu button to return to the main
menu.
With the menu button, select the personality mode (CHND) and press enter. This
fixture works with 9 and 11 DMX channels. Select the desired one and press enter.
Channel
Range
Function
CH1
0-255
Pan
CH2
0-255
Tilt
CH3
0-159
Colour change
160-255
Colour change slow to fast
CH4
0-63
Fix gobo
64-127
Gobo shake
128-255
Gobo change slow to fast
CH5
0-255
Strobe
CH6
0-255
Dimmer
CH7
0-255
Movement speed
CH8
0-255
Auto. Mode
CH9
250-255
Reset (5 sec. delay)
Channel
Range
Function
CH1
0-255
Pan
CH2
0-255
Pan Fine
CH3
0-255
Tilt
CH4
0-255
Tilt Fine
CH5
0-159
Colour change
160-255
Colour change slow to fast
CH6
0-63
Fix gobo
64-127
Gobo shake
128-255
Gobo change slow to fast
CH7
0-255
Strobe
CH8
0-255
Dimmer

CH9
0-255
Movement speed
CH10
0-59
Off
60-84
Auto mode 1
85-109
Auto mode 2
110-134
Auto mode 3
135-159
Sound mode 1
160-184
Sound mode 2
185-209
Sound mode 3
210-234
Sound mode 4
235-255
Sound mode 5
CH11
250-255
Reset (5 sec. delay)
Master/Slave mode
With the menu button, select the Master and Slave mode (SLND) and press enter.
Then use the “up” and “down” buttons to select between Master (MAST), Slave 1
(SL.1) and Slave 2 (SL.2).
Thanks to this mode, you can connect several Tagger 60 in a daisy chain and make
a nice lightshow. All the units will play in the same rhythm. To do so, put the first light
in your chain in “master” mode. Put the other ones in Slave 1 or 2. Slave 1 and 2 will
react in a different way to do a more complex lightshow.
Automatic mode
With the menu button, select the automatic mode (SHND) and press the enter key to
confirm. Then use the up and down buttons to choose the desired mode from SH.0
to SH.3.
Sound Mode
With the menu button, select the Sound mode (SOUD) and press the enter key to
confirm. Then use the up and down buttons to select if “YES” or “NO” the automatic
mode need to be sound controlled.

Sound sensibility
With the menu button, select the sound sensibility setting (SENS) and press the
enter key to confirm. Then use the up and down buttons to choose the desired
sensibility of the internal microphone from 000% to 100%.
Blind Menu
With the menu button, select the automatic mode (BLND) and press the enter key to
confirm. Then use the up and down buttons to choose the best action to do if the
DMX signal is lost:
-bLAc: Switch the unit in standby mode. Dimmer at 0.
-Auto: Switch the unit into automatic mode.
-Soun: Switch the unit in automatic mode with sound activated sequences.
-HoLd: The unit freeze with the last received parameters.
Other Settings
Use the menu button to change some parameters:
-Led: “On” or “Off”. On “Off” position, the display automatically shut down after 8
seconds.
-Disp: Let you define if the display has to be read upside down. For example, if you
hang it to a truss.
-rPAN: Reverse horizontal movements.
rTILT: Reverse vertical movements.
Rset: Reset all factory settings.

DMX512 CONNECTIONS
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
Warning
To avoid signal transmission problems and interferences when using fixtures in
chain, use a Stagg N-series professional 3-pin DMX terminator (resistance: 120
ohms; pin2: DMX-; pin3:DMX+).
FIXTURE CLEANING
An internal cleaning must be carried out periodically to optimize the light output. The
cleaning frequency depends on the environment in which the fixture operates: A
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt
on the fixture’s optics. Clean the fixture with a soft cloth and normal glass cleaning
fluid. Always dry the parts carefully. Clean the internal optics at least every 30 days.
Clean the external optics at least every 20 days.

For more info and the latest product updates:
staggmusic.com
EMD Music S.A.
Boulevard Général Wahis 16A
1030 Brussels
Belgium
05/2018