Stamina Folding Recumbent Bike 15-0200A User manual

Owner's Manual
Model#: 15-0200A
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
Exercise can present a health
risk. Consult a physician
before beginningany exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
allinstructionsarenotfollowed.
Keep others and pets away
from equipment when in use.
Alwaysmakesureallboltsand
nuts are tightened prior to
each use. Follow all safety
instructions in this manual.
When calling for parts or
service, please specify the
following number:
WARNING
CAUTION:
Weight on this product should not exceed 250 lbs.
2008, 09 2008 Stamina Products, Inc.
2040 N. Alliance, Springfield, MO 65803
Customer Service
1 [phone]
www.staminaproducts.com
This Product is Produced Exclusively by

TABLE OF CONTENTS
Before starting any exercise or conditioning program you should consult with your personal
physician to see if you require a complete physical exam. This is especially important if you
are over the age of 35, have never exercised before, are pregnant, or suffer from any
illness. READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY.
WARNING:
2
SAFETY INSTRUCTIONS
WARNING:
Read all warnings posted on the INTONE Folding Recumbent Bike.
TheINTONE Folding Recumbent Bike should only be used after a thorough review of the Owner's Manual.
We recommend that two people be available for assembly of this product.
Keep children away from the INTONE Folding Recumbent Bike. Do not allow children to use or play on
the INTONE Folding Recumbent Bike. Keep children and pets away from the INTONE Folding
Recumbent Bike when it is in use.
It is recommended that you place this exercise equipment on an equipment mat.
Set up and operate the INTONE Folding Recumbent Bike on a solid level surface. Do not position the
INTONE Folding Recumbent Bike on loose rugs or uneven surfaces.
Make sure that adequate space is available for access to and around the INTONE Folding Recumbent
Bike.
Adjust the Leveling Caps(50) on the Rear Stabilizer(3) so that the INTONE Folding Recumbent Bike sits
on the floor without rocking.
Inspect the INTONE Folding Recumbent Bike for worn or loose components prior to use. Tighten/replace
any worn or loose components prior to using the INTONE Folding Recumbent Bike.
Each user should adjust the seat per instructions on page 11.
Make sure the Seat Frame(5) is locked properly by the Adjustment Knob(41) located on the Main Frame(1).
Makesure the Back Support(6) is locked properly bythePegsontheSeatFrame(5) and the Locking Knob(45).
Make sure the Rear Frame(2) is locked properly by the Pull Pin(47) when in storage.
Keep fingers clear of all pinch points when folding and unfolding the INTONE Folding Recumbent Bike.
Consult a physician prior to commencing an exercise program. If at any time during exercise you feel faint,
dizzy, or experience pain, stop and consult your physician.
Follow your physician's recommendations in developing your own personal fitness program.
Always choose the workout which best fits your physical strength and flexibility level. Know your limits and
train within them. Always use common sense when exercising.
Do not wear loose or dangling clothing while using the INTONE Folding Recumbent Bike.
Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross
training shoes that fit well, provide foot support, and feature non-skid rubber soles.
Be careful tomaintain your balance while using, mounting, dismounting, orassembling the INTONE Folding
Recumbent Bike; loss of balance may result in a fall and serious bodily injury.
The INTONE Folding Recumbent Bike should not be used by persons weighing over 250 pounds.
The INTONE Folding Recumbent Bike should be used by only one person at a time.
The INTONE Folding Recumbent Bike is for consumer use only. It is not for use in public or semipublic
facilities.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Safety Instructions 2
Before You Begin 4
Hardware Identification Chart 5
Assembly Instructions 6
Set Up Instructions 9
Operational Instructions 10
Maintenance 11
Storage 12
Conditioning Guidelines 13
Warm-Up and Cool-Down 14
Warranty 15
Product Parts Drawing 16
Parts List 17
Fax/Mail Ordering Form 19
Page Page
To reduce the risk of serious injury, read the following Safety Instructions before
using the INTONE Folding Recumbent Bike.

3
THANK YOU FOR PURCHASING THE
STAMINA INTONE Folding Recumbent Bike
To help you get started, we have pre-assembled most of your
INTONE Folding Recumbent Bike at the factory with the exception
of those few parts left unassembled for shipping purposes.
Simply follow the few assembly instructions set forth in this manual.
With regular workouts, you will be getting your body into shape
and be on your way to achieving a happier and healthier lifestyle.
Should you have any questions,
please call our Customer Service Department toll-free number,
1 [phone]
Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.
Friday, 8:00 A.M. - 3:00 P.M., Central Time.
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springfield, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[e-mail]
www.staminaproducts.com
CALL US FIRST
Customer Service
1(800)375-7520
www.staminaproducts.com

4
Seat Frame
THE FOLLOWING TOOL IS INCLUDED FOR ASSEMBLY :
Left Cover
Rear Frame
Front Stabilizer
Right
Cover
Crank
Endcap
Left Pedal
Handrail
Rear Stabilizer
Adjustment Knob
Meter
Tension Knob
Seat
Leveling Cap
Back Support
Back Cushion
Moving Wheels
Combination Wrench
BEFORE YOU BEGIN
Right Pedal
Main Frame
Thank you for choosing the INTONE Folding
Recumbent Bike. We take great pride in producing
this quality product and hope it will provide many
hoursof qualityexercise tomakeyou feelbetter,look
better, and enjoy life to its fullest.
It's a proven fact that a regular exercise program
can improve your physical and mental health. Too
often,ourbusy lifestyleslimitourtimeandopportunity
to exercise. The INTONE Folding Recumbent
Bike provides a convenient and simple method to
beginyour assault ongettingyour bodyin shape and
achieving a happier and healthier lifestyle.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Read this manual carefully before using the
INTONE Folding Recumbent Bike.
Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your INTONE Folding
Recumbent Bike, please do not return the product.
Contact us FIRST!
If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
ServiceStaffis availabletoassistyou from 7:30A.M.
to5:00P.M.(CentralTime)Monday throughThursday
and 8:00A.M. to 3:00 P.M. (Central Time) on Friday.
If you would like to contact us online, go to our
websiteatwww.staminaproducts.com and accessthe
Customer Service section.
Be sure to have the name and model number of the
product available when you contact us.

5
Part No. and Description Qty
56 Carriage Bolt (M8 x 1.25 x 60mm) 4
57 Carriage Bolt (M8 x 1.25 x 85mm) 1
64 Bolt, Hex Head (M8 x 1.25 x 20mm) 4
65 Bolt, Hex Head (M8 x 1.25 x 40mm) 2
69 Acorn Nut (M8 x 1.25) 4
74 Arc Washer (M8) 6
75 Washer (M8) 5
60 Screw, Round Head (M5 x 0.8 x 10mm) 2
HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers or the
ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the
length of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat heads,
is measured from below the head to the end of the bolt or screw.
Flat head bolts and screws are measured from the top of the
head to the end of the bolt or screw.
mm.
in.
INCHES
MILLIMETERS
11/2021/2 31/2 41/2 51/2 61/2
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
6 8 10 12
3/16" 5/16" 1/2"3/8"1/4"
length
length
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.

STEP 1
The FRONT STABILIZER(4) has two MOVING WHEELS(48) with an "R" decal on one end. Attach the
FRONT STABILIZER(4) to the MAIN FRAME(1) with the wheels facing front and the "R" decal at the right
side as shown in the illustration. Secure with the CARRIAGE BOLTS(M8x1.25x60mm)(56), ARC
WASHERS(M8)(74), and ACORN NUTS(M8x1.25)(69).
STEP 2
Attach the REAR STABILIZER(3) totheREAR FRAME(2) with CARRIAGE BOLTS(M8x1.25x60mm)(56),
ARC WASHERS(M8)(74), and ACORN NUTS(M8x1.25)(69).
NOTE:
R
6
ASSEMBLY INSTRUCTIONS
You can adjust the LEVELING CAPS(50) on the REAR STABILIZER(3) to keep the INTONE
Folding Recumbent Bike stable.
Nylock Nut(M8)
Plastic Washer
Fixing Tube
NOTE: Remove the FIXING TUBES,WASHERS, andNUTS from MAIN FRAME(1) and REAR FRAME(2)
beforeany assembly. These parts areonly for packing,do not disposeof the packing materials
until assembly is completed.
STEP 3
Store the PULL PIN(47) by inserting the pin into the hole in the REAR FRAME(2).
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materials from your area and place them back into the box.Do not dispose of the packing materials
until assembly is completed. Read each step carefully before beginning. If you are missing a part please call
ourtoll-free number forassistance 1-800-375-7520or e-mail usat [e-mail].

ASSEMBLY INSTRUCTIONS
7
STEP 4
Attach the SEAT(43) to the SEAT FRAME(5) with HEX BOLTS(M8x1.25x20mm)(64) and WASHERS(M8)
(75). Pull the ADJUSTMENT KNOB(41), then insert the SEAT FRAME(5) into the MAIN FRAME(1) and
secure with the ADJUSTMENT KNOB(41).
NOTE: ItmaybenecessarytounscrewtheADJUSTMENT KNOB(41)slightlytoinserttheSEATFRAME(5).
Make sure that the pin on the ADJUSTMENT KNOB(41) is inserted into one of the holes in the
SEAT FRAME(5).
TheADJUSTMENT KNOB(41)should bescrewedintighttomaketheSEAT FRAME(5)fitsecurely
in the MAIN FRAME(1).
1.
2.
3.
STEP 5
Attach the BACK SUPPORT(6) to the SEAT FRAME(5) by sliding the slots in the end of the BACK
SUPPORT(6) ontothe pegsonthe SEAT FRAME(5) andsecuringwith CARRIAGE BOLT(M8x1.25x85mm)
(57), SPACER(80) ,WASHER(M8)(75), and the LOCKING KNOB(45).
STEP 6
Attach the HANDRAIL(7) to the SEAT FRAME(5) with HEX BOLTS(M8x1.25x40mm)(65) and ARC
WASHERS(M8)(74).
Peg

ASSEMBLY INSTRUCTIONS
8
STEP 7
NOTE:
Thread the RIGHT PEDAL(40) onto the right side of the CRANK(8). Thread the LEFT PEDAL(39) onto the
left side of the CRANK(8).
STEP 8
Refer to the illustration. Swing the METER BRACKET(31) up to a position where it can be seen while
working out. NOTE: If necessary, loosen or tighten the HEX BOLT(M8x1.25x55mm)(66). The HEX
BOLT(M8x1.25x55mm)(66) should be tight enough to secure and hold the METER(32) in place yet loose
enough for the METER(32) to be adjusted.
Install two AA batteries into the METER(32), two batteries included. See page 10 for detailed battery
installation instructions. Run the connection wire on the METER(32) through the hole in the METER
BRACKET(31). Then attach the METER(32) to the METER BRACKET(31) with ROUND HEAD
SCREWS(M5x0.8x10mm)(60). Plug the SENSOR WIRE(33) into the connection wire of the METER(32).
The RIGHT PEDAL(40) has Rstamped on the end of the pedal shaft. The RIGHT PEDAL(40) has
right hand threads and is tightened by turning clockwise. The LEFT PEDAL(39) has Lstamped on
the end of the pedal shaft. The LEFT PEDAL(39) has left hand threads and is tightened by turning
counter clockwise.

SET UP INSTRUCTIONS
9
Place the INTONE Folding Recumbent Bike in the area where it will be used. It is recommended that the
INTONE Folding Recumbent Bike be placed on an equipment mat.The maximum operation dimensions
of the INTONE Folding Recumbent Bike are approximately 42 1/4" long x 25 3/8" wide x 44 1/4" tall.
(These dimensions may vary up to one inch.) An area 4 feet wide x 6 feet long is required for safe operation
of the INTONE Folding Recumbent Bike. Make sure that adequate space is available for access to and
passage around the INTONE Folding Recumbent Bike.
Adjust the LEVELING CAPS(50) on the REAR STABILIZER(3) so that the INTONE Folding
Recumbent Bike sits on the floor without rocking.
The INTONE Folding Recumbent Bike has a pair of MOVING WHEELS(48) on the FRONT
STABILIZER(4). Fold the INTONE Folding Recumbent Bike. Grasp the HANDRAIL(7) and
tip the INTONE Folding Recumbent Bike forward to move.
LEVELING:
Equipment Mat
(not included)
FUNCTION INSPECTION:
Visually inspect the INTONE Folding Recumbent Bike to verify that assembly is as shown in the above
illustration. Check the function of the INTONE Folding Recumbent Bike. Turn the crank slowly through
one complete revolution to verify that the drive train functions properly.Adjust the TENSION KNOB(29) and
verify that it functions properly.
Locateandreadthe WARNING LABEL(77) on theINTONE Folding Recumbent Bike. Make
sure that all users read the WARNING LABEL(77).
CAUTION:
MOVING:

10
USING THE ELECTRONIC METER
CALORIE:
TIME:
DISTANCE:
POWER OFF:
Automaticallyscans SPEED,DISTANCE, TIME, and CALORIE in sequence witha change
every five seconds. Press and release the MODE button until the arrow on the display
points to "SCAN".
Automaticshutoffafterthree minutesof inactivity.
POWER ON:
FUNCTIONS:
Displays the time from one second up to 99:59 minutes.
SPEED:
SCAN:
FUNCTION BUTTONS :
MODE : Press and release to select the function to display on
the screen.
Press the button and hold it down for two seconds to
reset all functions to zero.
RESET :
Displays the current speed from zero to 999.9 miles per hour.
Displays the calorie consumption from zero to 999.9 Kcal.
Thecaloriereadoutis an estimate foranaverageuser.It shouldbeusedonly asacomparison
between workouts on this unit.
Displays distance from the time the meter is turned on to 999.9 miles.
OPERATIONAL INSTRUCTIONS
Pedal movement or press any button.
Open the Battery Door on the back of the meter.
The meter operates with two AA batteries, included. Refer to the
illustration to install or replace the batteries.
1.
2.
HOW TO INSTALL AND REPLACE BATTERIES:
Do not mix a new battery with an old battery.
Use the same type of battery. Do not mix an alkaline battery with
another type of battery.
Rechargeable batteries are not recommended.
1.
2.
3.
NOTE:
The meter will shut off automatically after four minutes of inactivity. All function values will
be kept. Push the RESET button to reset the functions to zero.
NOTE:
AABatteries

OPERATIONAL INSTRUCTIONS
SEAT ADJUSTMENT
CAUTION:
Turn the ADJUSTMENT KNOB(41) to loosen, then pull
the ADJUSTMENT KNOB(41) to release the pin. Slide
the SEAT FRAME(5) until the SEAT(43) is at the proper
height. Release the ADJUSTMENT KNOB(41) making
sure the pin catches in one of the holes of the SEAT
FRAME(5) and tighten the ADJUSTMENT KNOB(41).
1.
Proper seat adjustment is important.
Do not attempt to adjust the seat while you are on the
INTONE Folding Recumbent Bike.
Always tighten the ADJUSTMENT KNOB(41) after
adjusting the seat to a new position.
1.
2.
To increase the load, turn the TENSION KNOB(29) clockwise.
Todecreasetheload,turnthe TENSION KNOB(29)counterclockwise.
MAINTENANCE
The safety and integrity designed into the INTONE Folding Recumbent Bike can only be maintained
whenthe INTONE Folding Recumbent Bike is regularlyexamined fordamageand wear.Specialattention
should be given to the following:
Adjust the TENSION KNOB(29) and verify that the Magnetic System provides tension. The Magnetic
System should provide many years of use.
It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.
Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.Tighten
loose nuts and bolts.
Worn or damaged components shall be replaced immediately or the INTONE Folding Recumbent
Bike removed from service until repair is made.
Only Stamina Products supplied components shall be used to maintain/repair the INTONE Folding
Recumbent Bike.
Keep your INTONE Folding Recumbent Bike clean by wiping with an absorbent cloth after use.
1.
2.
3.
4.
5.
6.
LOAD ADJUSTMENT
11
Sit on the seat and place your feet on the pedals. You
should be able to move through a complete pedal stroke
without locking your knees or shifting your hips on the
seat.The seat is too close to the pedals if you have more
thana slightbend inyour kneesatthe bottomof thepedal
stroke. The seat is too far from the pedals if you have to
completely straighten your knees at the bottom of the
pedal stroke. Refer to the illustration.
2.

STORAGE
To store the INTONE Folding Recumbent Bike simply keep it in a clean dry place.
The minimum folded dimensions of INTONE Folding Recumbent Bike are approximately 21 5/8" long
x253/8" widex421/4"tall. Pleasemeasure yourINTONE Folding Recumbent Bike ifexactdimensions
are needed.
The INTONE Folding Recumbent Bike has a pair of MOVING WHEELS(48) built into the FRONT
STABILIZER(4). To move the bike, grasp the HANDRAIL(7), tip the INTONE Folding Recumbent
Bike forward slowly, and roll into or out of the storage area.
To avoid damage to the METER(32), remove the batteries before storing the INTONE Folding
Recumbent Bike for one year or more.
Follow the illustrated process below to fold the INTONE Folding Recumbent Bike.
1.
2.
3.
4.
5. Loosen the LOCKING KNOB(45). Lift up the BACK SUPPORT(6) and fold it forward. Tighten the
LOCKING KNOB(45) after folding.
Remove the PULL PIN(47) from the REAR FRAME(2). Fold the REAR FRAME(2) close to the MAIN
FRAME(1) and lock it in folded position with the PULL PIN(47).
NOTE:
B
12
D
A
C
Loosenandpull theADJUSTMENT KNOB(41), thenlower theSEAT FRAME(5) tothelowestposition.
Lock the SEAT FRAME(5) into position by releasing and retightening the ADJUSTMENT KNOB(41).
Swing the METER(32) down toward the floor as shown in illustration D.
a.
b.
MakesuretheLOCKING PIN(47) goesthrough theholesonboth sidesofthe REARFRAME(2)
and the ring on the MAIN FRAME(1).
NOTE:
c.
When you fold the INTONE Folding Recumbent Bike without changing the seat height or the
angle of the METER(32) as described in the steps above and as shown in illustration C, there is
no need to readjust your seat height or meter angle before your next workout. You can fold your
INTONE Folding Recumbent Bike smaller by following the next step.

CONDITIONING GUIDELINES
How you begin your exercise program depends on your physical condition. If you have been inactive for
several years or are severely overweight, start slowly and increase your workout time gradually. Increase
your workout intensity gradually by monitoring your heart rate while you exercise.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic
capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise so
you don't tire too quickly.
Measure your heart rate periodically during your workout by stopping the
exercise but continuing to move your legs or walk around. Place two or three
fingersonyour wrist and takea six secondheartbeat count.Multiplytheresults
by ten to find your heart rate. For example, if your six second heartbeat count
is 14, your heart rate is 140 beats per minute. A six second count is used
because your heart rate will drop rapidly when you stop exercising.Adjust the
intensity of your exercise until your heart rate is at the proper level.
wrist pulse
Have your doctor review your training and diet programs.
Begin your training program slowly with realistic goals that have been set by you and your physician.
Warm up before you exercise and cool down after you work out.
Take your pulse periodically during your workout and strive to stay within a range of 60% (lower
intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and
build up to higher intensity as you become more aerobically fit.
If you feel dizzy or lightheaded you should slow down or stop exercising.
Target Heart Rate Zone Estimated byAge*
Remember to follow these essentials:
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table below.
For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of
your maximum heart rate. If just starting an exercise program, work out at the low end of your target heart
rate zone.As your aerobic capacity improves, gradually increase the intensity of your workout by increasing
your heart rate.
Forcardiorespiratorytraining benefits,theAmericanCollege ofSports Medicinerecommendsworking
out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart
rate, the following formula was used: 220 - Age = predicted maximum heart rate
*
20 years
25 years
30 years
35 years
40 years
45 years
50 years
55 years
60 years
65 years
70 years
Target Heart Rate Zone
(55%-90% of Maximum Heart Rate) Average Maximum Heart Rate 100%
Age
110-180 beats per minute
107-175 beats per minute
105-171 beats per minute
102-166 beats per minute
99-162 beats per minute
97-157 beats per minute
94-153 beats per minute
91-148 beats per minute
88-144 beats per minute
85-139 beats per minute
83-135 beats per minute
200 beats per minute
195 beats per minute
190 beats per minute
185 beats per minute
180 beats per minute
175 beats per minute
170 beats per minute
165 beats per minute
160 beats per minute
155 beats per minute
150 beats per minute
13

14
WARM-UP and COOL-DOWN
Warm-Up The purposeof warming upis to prepareyour body forexerciseandtominimizeinjuries.Warm
up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your
heart rate and warm the working muscles.Activities may include brisk walking, jogging, jumping jacks, jump
rope, and running in place
Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength
or aerobic training session is very important. Muscles stretch more easily at these times because of their
elevatedtemperature,which greatlyreducesthe riskofinjury. Stretchesshould beheld for15 to30 seconds.
Do not bounce.
Suggested Stretching Exercises
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state
at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to
return to the heart.Your cool-down should include the stretches listed above and should be completed after
each strength training session.
Lower Body Stretch
Place feet shoulder-width
apart and lean forward.
Keep this position for 30
seconds using the body as a
natural weight to stretch the
backs of the legs.
DONOT BOUNCE!
When the pull on the back of
the legs lessens, gradually
try a lower position.
Floor Stretch
While sitting on the floor,
open the legs as wide as
possible. Stretch the upper
body toward the knee on the
right leg by using your arms
to pull your chest to your
thighs. Hold this stretch 10
to 30 seconds.
DONOT BOUNCE!
Do this stretch 10 times.
Repeat the stretch with the
left leg.
Bent Over Leg Stretch
Stand with feet shoulder-
width apart and lean forward
as illustrated. Using the
arms, gently pull the upper
body towards the right leg.
Let the head hang down.
DONOT BOUNCE!
Hold the position a minimum
of 10 seconds. Repeat
pulling the upper body to the
left leg. Do this stretch
several times slowly.
Bent Torso Pulls
While sitting on the floor,
have legs apart, one leg
straight and one knee bent.
Pull the chest down to touch
the thigh on the leg that is
bent,and twist at the waist.
Hold this position at least 10
seconds. Repeat 10 times
on each side.

15
WARRANTY
LIMITED WARRANTY MODEL 15-0200A
Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship
under normal use, service and proper operation for a period of 90 days on the parts and three years on the
frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT
APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE,
ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY REPAIR,
REPLACEMENT, SUBSTITUTIONORUSEWITH PARTS OTHER THANPARTS PROVIDED BYSTAMINA
PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas,
gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is
in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household
purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and
abriefdescriptionofthe defectalongwithyour receiptto Stamina Products, Inc. P.O. Box1071, Springfield
Missouri, USA, 65801-1071, or email us at [e-mail], or call us at
1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the
product or part to us for free repair or replacement at our option. NO ACTION FOR BREACH OF THIS
LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE
ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF
ANY IMPLIEDWARRANTY MAY BE COMMENCED MORE THAN ONE (1)YEAR AFTERDELIVERY OF
THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF ANY PART OF THE
PRODUCT ISNOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANYIMPLIED WARRANTY,
THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDYAVAILABLE TO YOU. In
theeventthat thepurchaser makesanyclaimunder thislimited warranty oranyimpliedwarranty,theWarrantor
reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the
Warrantor'spremisesinSpringfield, Missouri.Return ofthe enclosedwarrantyregistration cardis notrequired
for warranty coverage, but is merely a way of establishing the date and place of purchase.
Stamina Products, Inc. SHALLNOT BE LIABLE FOR THE LOSS OF USE OFANY PRODUCT, LOSS OF
TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,
SPECIALOR INCIDENTALDAMAGESDUETO BREACH OF THEABOVEWARRANTYORANYIMPLIED
WARRANTY.
This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warranty
gives you specific legal rights, and you may also have other legal rights which vary from state to state.
ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR
MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE, IS LIMITED INDURATION TO THE
DURATION OF THIS WARRANTY.
The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to
disclaim or limit implied warranties and consequential and incidental damages with respect thereto. If any
suchlaw is foundto beapplicable, theforegoing disclaimers and limitationsof andon impliedwarrantiesand
consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to
have been made to the extent necessary to comply with such legal restriction.

PRODUCT PARTS DRAWING
BACK
FRONT
16

1 Main Frame 1
2 Rear Frame 1
3 Rear Stabilizer 1
4 Front Stabilizer 1
5 Seat Frame 1
6 Back Support 1
7 Handrail 1
8 Crank 1
9 Bearing Housing 2
10 Ball Bearing 2
11 Inside Bearing Collar 1
12 Outside Bearing Collar 1
13 Bearing Washer 1
14 Bearing Snap Washer 1
15 Bearing Nut 2
16 Pulley 1
17 V-Ribbed Belt 1
18 Idler Arm 1
19 Bearing (608zz) 2
20 C Ring (8mm) 2
21 Tension Spring 1
22 Magnetic Flywheel 1
23 Small Pulley/w Shaft 1
24 Bearing (6004zz) 2
25 C Ring (20mm) 1
26 Key 1
27 Wave Washer (M8) 1
28 Magnetic Brake 1
29 Tension Knob 1
30 Spring 1
31 Meter Bracket 1
32 Meter 1
33 Sensor Wire 1
34 Grommet Plug 1
35 Magnet 1
36 Left Cover 1
37 Right Cover 1
38 Ring Cap 1
39 Left Pedal 1
40 Right Pedal 1
41 Adjustment Knob 1
42 Bushing 1
43 Seat 1
44 Back Cushion 1
45 Locking Knob 1
46 Foam Grip 2
47 Pull Pin 1
48 Moving Wheel 2
17
PARTS LIST
PART# PART NAME QTY

PARTS LIST
PART# PART NAME QTY
49 Protection Pad 1
50 Leveling Cap (50mm) 2
51 Endcap (50mm) 2
52 Rectangular Plug (30mm x 60mm) 2
53 Square Plug (30mm x 30mm) 1
54 Dome Plug (25mm) 2
55 Oval Plug (20mm x 40mm) 2
56 Carriage Bolt (M8 x 1.25 x 60mm) 4
57 Carriage Bolt (M8 x 1.25 x 85mm) 1
58 Screw, Round Head (M3 x 10mm) 2
59 Screw, Round Head (M4 x 20mm) 6
60 Screw, Round Head (M5 x 0.8 x 10mm) 2
61 Screw, Round Head (M5 x 0.8 x 15mm) 1
62 Bolt, Round Head (M6 x 1 x 15mm) 1
63 Bolt, Hex Head (M6 x 1 x 47mm) 2
64 Bolt, Hex Head (M8 x 1.25 x 20mm) 5
65 Bolt, Hex Head (M8 x 1.25 x 40mm) 4
66 Bolt, Hex Head (M8 x 1.25 x 55mm) 1
67 Bolt, Hex Head (M10 x 1.5 x 110mm) 1
68 Nut (M6 x 1) 1
69 Acorn Nut (M8 x 1.25) 4
70 Nylock Nut (M6 x 1) 2
71 Nylock Nut (M8 x 1.25) 2
72 Nylock Nut (M10 x 1.5) 2
73 Lock Washer (M8) 1
74 Arc Washer (M8) 6
75 Washer (M8) 11
76 Washer (M10) 3
77 Warning label 1
78 Combination Wrench 1
79 Manual 1
80 Spacer 1
18

IMPORTANT: Before filling out the form below make sure you have the right information.
Refer to the parts list to make sure you're ordering the right parts!
Detach and Mail or Fax the Form Below
Stamina Products, Inc.
P.O. Box 1071
Springfield, MO 65801-1071
IMPORTANT: We must have your phone number in order to process the order!
FAX/MAIL ORDERING FORM
Please do not return the product. For your convenience, Stamina's Customer Service Department can be
reached by email at [e-mail] or toll free at 1-800-375-7520 (in the U.S.).
Should a part be missing or a defective part found, please call us from 7:30A.M. to 5:00 P.M. Central Time,
Monday through Thursday and 8:00A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below
and fax it to [phone]. Our Customer ServiceDepartment will be able to assist you with your problem
and the part will be mailed directly to your house.
Mr./Ms:
Address: Apt. #:
City: State: Zip Code:
Phone #: ( ) Work Phone #: ( )
Date Purchased:
Model #:
Purchased From:
PART # DESCRIPTION QUANTITY
1 Rear Unit Assembly 1
EXAMPLE:
TELEPHONE
CUSTOMER SERVICE
Tel: [phone]
FAX
CUSTOMER SERVICE
Fax: [phone]
MAIL
STAMINA PRODUCTS, INC.
ATTN: Customer Service
P.O. Box 1071
Springfield, MO. 65801-1071
ONLINE
CUSTOMER SERVICE
[e-mail]
www.staminaproducts.com