STAMPLINE S-120 User manual

S-120
S-120
POLYMER SYSTEM STAMP MACHINE
POLYMER SYSTEM STAMP MACHINE
MAINTENANCE AND USER GUIDE
MAINTENANCE AND USER GUIDE

STAMP MACHINE OPERATING MANUALSTAMP MACHINE OPERATING MANUAL
S-120
S-120
Digital Control Panel
20 W UV Fluorescent
Exposure Area
Last Exposure Drawer
Thank you for choosing STAMPLINE S-120,microprocessor controlled polymer system stamp machine.
This manual includes the information about installation of the polymer system stamp machine, all the
steps for settings and stamp production process, additionally all the information about stamp materials.
All rights are reserved by Matuya Makine Sanayi ve Ticaret
STAMPLINE S-120 is the state-of-art
Limited Şirketi
Package Content
· The machine unit
· Power cable,
· Operating manual
· Warranty certificate.
polymer system stamp machine which enables the fastest
and the highest quality rubber stamp production by exposing liquid polymer. Your stamp designs come
to life in the easiest way by STAMPLINE S-120, by placing polymer stamp materials on the
exposure area of the machine which is controlled by a digital control panel.
1- PRODUCT DESCRIPTION and STRUCTURE
a-
b- Unit Structure
Purpose of Use
S120/1

2- MACHINE INSTALLATION and SAFETY INSTRUCTIONS
3- CONTROL PANEL and FUNCTIONS
Plug the grounded power cable given together with the machine in the power socket at the back and plug the
other end in the mains.
Press the switch at the back of the machine to turn the power “ON”.
Push the
These are all the steps necessary to make the machine ready to use.
STAMPLINE S-120 polymer system stamp machines are designed and manufactured according to the CE
regulations in order to provide your personal safety. Please follow the basic rules listed below for your safety.
Insert power cord into the grounded mains which to be matching the voltage value indicated
on the label placed at the back of the machine. If sudden electrical power surges are likely in your location,
it’s recommended to use regulator. Power supply cables should be routed so that they are not likely to be
walked on or damaged by items placed against them. Do not overload wall outlets, extension cords or
regulators with other devices in order to prevent risk of fire or electrical shock.
The machine should be placed on a stable, well-balanced and clean surface. Do not
place the machine on an unbalanced surface. The machine should be situated away from heat sources and
other equipment that may generate excessive vibration, dust or moisture.
The reparation of the machine must be done by the authorized technicians.
STAMPLINE S-120 stamp machine is designed and engineered in a way protecting the
operator against electrical shocks. All case covers have been grounded and a fuse is placed on the plug
socket to prevent electrical leakage.
Do not use any attachments not supplied by MATUYA with the STAMPLINE S-120 stamp
machine as this may cause hazards.
Do not put weight on the machine during transportation. Keep the machine package fixed
inside the vehicle to avoid stroking. Pay attention when carrying the machine as it is made up of sensitive
electronic systems. Stick “Fragile” label on the carton. The materials used in the machine during production
don’t cause any danger according to the international transportation rules.
a- Installation
b- Safety Instructions
220 Volt (50/60Hz)
“POWER” button placed on the digital control panel to start the machine.
· Power Source:
· Machine Placement:
· Reparation:
· Safety Measures:
· Attachments:
·Transportation:
2x16 LCD Screen
Power On/Off
Button
Vacuum
Button
Program
Button
Stop Button
Start
Button
Cancell
Button
Enter
Button
Timer Setting Buttons
S120/2

4- STAMP MAKING PROCESS with STAMPLINE S-120
1. Press the POWER button to turn ON and open the cover of the exposure area.
2. Lift up the upper glass and place the negative film on the lower glass in reading direction.
3. Cover the negative film with cellophane sheet.
4. Pressing the vacuum button, start vacuuming and ensure that there will be no air pocket left between the
cellophane coating and the negative film.
5. Surround the negative film (image) with damming tape to form a pool (use 3mm damming tape for
standard stamps, 2mm for pen stamps).
6. Pour the liquid polymer into the pool. In order to eliminate the air bubbles coming out when pouring
the polymer, press on the vacuum button and remove the bubbles with compressor hose.
7. Place the matte acetate sheet onto the liquid photopolymer without leaving any air, close the upper
glass and lock.
8. Close the upper cover of the machine and;
“ ”
a) for the first exposure (posing) press “PRG” button and set the menu to “1. POSE” status. In the next
step press “ENTER” button and set the timing using the numeric buttons; again press “ENTER” for
recording to memory. In order to start the timer, press “START” button (if you want to cancel the
operation press “STOP”).
b) for the second exposure, using “PRG” button set the menu to “2. POSE” status. Repeat the same
process of first exposure.
9. After finishing the exposure process, open the upper cover of the machine and separate the glasses.
Peel the cellophane sheet coating off the processed polymer. The matte acetate sheet (substrate)
will remain merged to the bottom of polymer.
10. In order to clean the remaining soft polymer between the letters on the exposed polymer plate, wash
it with a soft brush in a tray full of detergent.
11. For the last exposure, open the drawer under the exposure area, place the polymer plate inside and
add some last exposure liquid (hardening solution).
12. For this process, press the “PRG” button and set the menu to “LAST POSE” status then repeat the
same timing process for the previous exposure(generally chosen hardening time is 500 seconds but
the ideal time is 900 seconds).
13. After the last exposure, take out the polymer plate, rinse under water and dry the plate.
14. At the final step you can trim the polymer plate and install in stamp mount.
1. Print out your design as positive and reversed.
2. Start the machine by pressing button and open the drawer for exposure.
3. Lift up the upper glass and place the matte daylight film on the lower glass. Place your printout on the
daylight film as its printed surface will face the daylight film.
4.
5. For setting up the timer, enter the time using the 1. Pose section and start.
6. After finishing the exposure, unlock the glasses and take out the daylight film.
7. Insert the daylight film into a tray full of developer or AB liquid and keep inside until it reaches the
appropriate darkness.
8. After taking out the film from developer or AB liquid, insert it into the Fixer for having contrast for the
writings.
9. After keeping the film in the Fixer for a sufficient time, rinse it under tap water and dry.
10. Your negative film is ready to use.
“POWER”
For vacuuming process,place the vacuuming folio on the top and vacuum.Vacuuming is very important
in film making so printed surface must contact the sensitive surface of the daylight film perfectly. After
vacuuming close the upper glass and lock the glasses, then close the exposure drawer.
NEGATIVE FILM PRODUCTION
NEGATIVE FILM PRODUCTION
S120/3

5- CLEANING and MAINTENANCE
6- TECHNICAL DETAILS
WARRANTY
Daily cleaning of the machine must be done by the operator. A soft moist duster should be used for
cleaning. It’s very important to keep the glasses clean and dust-free in the exposure area. You can use
mild household glass cleaner on the glasses. Do not spray the cleaners directly on the machine.
STAMPLINE S-120 microprocessor controlled stamp machine doesn’t require periodical maintenance.
- STAMPLINE S-120 is a microprocessor controlled stamp machine.
- The machine has 2x16 LCD screen and control panel with membrane buttons.Using single button
whole system can be operated and controlled in one screen.
- Stampline S-120 polymer system stamp machine has 20x30 cm processing area.
-
- Time adjustment can be set up to 9999 seconds on the liquid-crystal-screen and together with the
memory unit and the audial alarm system enables easy usage.
- Stampline S-200 has whole touch system.
- The machine has special tempered glass and glass locks on the exposure area, also has a perfect
and .
- It has a posing (exposure) system with 12 pcs of 20W UV Philips fluorescent lamps; 6 pcs of them are
placed at the up and other 6 pcs are placed at the down side.
- Tridonic brand electronic balances ensure to start the exposure system immediately unlike the
other starter systems, so the lifetime of the fluorescents increases up to 3 times longer. You can harden
the polymer plate sturdily in the specially designed chrome made hardening drawer.
Warranty period is 1 year and begins with the delivery of the machine. Please refer to
other details.
The case made of laser-cut chrome guarantees non-corrosion.
vacuum compressor
Warranty
Certificate for the
MATUYA Makine Sanayi ve Ticaret Ltd. Şti.
Cumhuriyet Mah. 625 Sk. No:6 Antalya / Turkey
+90 242 346 15 18 / +90 242 346 15 10
Kurumlar
328 004 1357
Manufacturing, Import, Export, Technical Service
MANUFACTURER
Company Title :
Address :
Phone/Fax :
Tax Administration :
Tax ID :
Field of Business :
S120/4
Table of contents
Other STAMPLINE Industrial Equipment manuals