STAND STEADY TRFSEL63BLBL User manual

ELECTRIC
SIT-STAND DESK
Instruction Manual
Connect the desk to power.
You can now use the sit-stand desk.
19
Operation Instruction:
Upward movement
Downward movement
Press the “ ” or “ ” and do not release until the
desk reaches the desired height. To avoid possible motor
damage, do not continuously operate the control panel
for over 2 minutes. Should the unit be operated over this
time, please allow the system to rest for at least 18
minutes prior to using it again.
Overload protection mode: the desk will enter overload
protection mode should the system exceed maximum
loaded weight. Should this occur, the system will power
off automatically. Before using it again, remove some
items on the desk until the system is within the
maximum loaded weight.
TRFSEL63BLBL

1 2
Preface
Electrical Safety Instructions:
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the
instructions carefully.
CAUTION
Don't clean the product with water
while the power is still connected.
Don't disassemble or replace components
while the power is still connected.
Never operate the system with a damaged cord or plug.
Please contact your point of purchase to replace the damaged parts.
Never operate the system if it's in moist environment
or its electrical components have contact with liquids.
Don't operate the system if the control box makes noise or
odor. Alterations of the given power unit and control box
aren't allowed.
Other Safety Instructions:
CAUTION
This electric height adjustable standing desk consists of a heavy-duty steel desk frame and a motorized
height adjustment system. Please read and completely understand this manual before installation in order
to make sure the safe and correct use of the system and maintain the longevity of the overall construction
and the built-in electronics.
Instructions of Safety and Warnings:
• Any incomplete observation of the instructions, warnings and additional information marked with the "Note"
and " " may result in serious damage to the system or its components.
• This product can be used by children aged from 8 years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision. Unplug the desk when the system isn't in use, and place the power plug out of children reach.
• Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
• Persons with reduced physical, mental abilities and or lack of experience and knowledge must not use the
product, unless they're under supervision, understand the hazards involved or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the safety of these persons.
• Users should make sure that they never sit on the desktop in order to prevent serious bodily injury.
• Clear up all obstacles within the height adjustment range.
• Don't leave the cords or plug unorganized in order to prevent tripping hazards.
• Any attempts to reconstruct the desk frame aren't allowed.
• Don't add anything to the adjustable junctions of the desk frame.
• Outdoor use is prohibited.
• The appliance is only to be used with the power supply unit provided with the appliance.

What are the specifications
you need to know?
1
Weight Capacity
70kg (154lbs)
Power Input
(100~240V)
Operation Temperature
(-5°C~+40°C)
What are the tools you
require while installation?
2
Bubble Level Allen Wrench
(Included)
Drill
3
A Shipping Blanket
to protect the desk
and the floor
Things you need to know
before installation
4Please check all of the components shown in the component checklist. If any of the components
are missing or damaged, contact your point of purchase for a replacement.
Disposal: The product with this mark indicates that this product shouldn't be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the local recycle service or contact
your point of purchase to withdrawn the product. This page can be torn so that it's easier for you to match the components with the images.
3 4
Preparation Checklist and Installation
What's the thing you'd
better have before
installation?
Phillips Screwdriver
A (x1)
Crossbar
H (x1)
Adapter Holder
C (x1)
Lifting Column
B (x1)
Lifting Column
I (x1)
AC Adapter
J (x1)
Power Plug
D (x1)
Crossbar Spacer
E (x2)
Side Bracket
F (x1)
Sync Rod
G (x2)
Foot
M (x1)
Desk Board
N (x1)
Surface Pad
o (x2)
Connecting Bar
K (x1)
Desk Board
L (x1)
Desk Board

5 6
S-A (x16)
Hex Head Screw
S-B (x20)
Phillips Head Screw
S-C (x2)
Phillips Head Screw
S-D (x3)
Cable Clip
Now let's start the installation.
S-F (x1)
Allen Wrench
S-E (x7)
Adhesive Pad
S-F
Shipping Blanket
A
Note: The drawing of the crossbar is the backside of it.
Assembling the Crossbar
• Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent
scratches on the floor and the frame.
• Loosen the hex head screws that fix the adjustable junction, but don't completely take out the screws.
S-G (x1)
Phillips Screwdriver

7 8
Installing the Side Brackets
E
S-A
S-F
• Attach the side bracket to the end of the lifting column with
2 screws using the Allen wrench as shown.
• Repeat the same process to assemble the other side bracket.
E
S-A S-F
• Attach one end of the crossbar and crossbar
spacer to the lifting column with 2 screws
using the Allen wrench as shown.
• Attach the other end of the crossbar to the
lifting column with 2 screws using the
Allen wrench .
S-F
S-A
D
C
Note: Maintain the lifting columns in a FACE DOWN
position during installation. This will aid in the remaining
assembly steps.
B
S-A
S-F
A
S-F
S-A
B
C
D
A

9 10
Assembling the Sync Rod
F
• Turn the right knob counterclockwise as shown to loosen the sync rod .
• Attach the end of the sync rod as shown to the motor spindle in red line
position and turn the right knob clockwise to tighten the connection.
3
2
F
2
• Turn the left knob clockwise as shown to loosen the sync rod.
• Insert the other end of the sync rod into the column as shown.
knob
1
knob
1