Standard Horizon PF-P310 User manual

OPERATORS MANUAL
Standard Horizon PF-P310 Paper Folder
Read this manual, and thoroughly
familiarize yourself with its
contents before operating or
servicing this equipment.
PF-P310/OM


I
PAPER FOLDER
Important Information
- This manual is designed to help you to install, operate and maintain the Table Top
Folder PF-P310. Read, understand and keep this manual in a safe and convenient
place.
- Do not operate the PF-P310 until you read and understand the instructions in this
manual.
- Horizon International Inc. shall not be liable for incidental consequential damages
resulting from : improper or inadequate maintenance by customer; unauthorized modi-
fication or misuse; operation outside of the environmental specifications for the prod-
uct.
- No Horizon dealer and distributor is authorized to make any modification, expres-
sion, or addition to the warranties written in contract.
- Horizon International Inc. pursues a policy of continuing improvement in design and
performance of the product. Therefore, the product design and specifications are sub-
ject to change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or
translated to another language without the prior written consent of Horizon Interna-
tional Inc.
010628/PFP310/03J/NO/MM/MM UM203001-03
PF-P310

II
Safety Precautions
- The signal word WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
- The signal word CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
- The signal word NOTE indicates a potentially hazardous situation which, if not
avoided, may result in damage on products.
- Read and understand all safety instructions with signal word such as WARNING,
CAUTION and NOTE. If safety instructions are ignored, personal injury will result.
- Observe the provisions of the federal, state, or local regulations, including OSHA.
- Horizon International Inc. cannot anticipate every possible situation that might in-
volve a potential hazard. The instruction in this manual and warning labels on the
machine are therefore not all inclusive.
- All equipment shall be locked out or tagged out to protect against accidental or inad-
vertent operation when such operation could cause injury to personnel. Do not attempt
to operate any switch, valve, or other energy isolating device where it is locked or
tagged out.
- Do not operate the machines with any covers being removed.
- Some of the drawings in this manual shows the machine uncovered for explaining the
detail or inside of machine.

III
Contents
1. Before You Begin ..................................................... 1
This section explains machine parts and their function.
1-1 Specifications ............................................................................2
1-2 Machine Parts Descriptions ......................................................3
1-2-1 General View ...................................................................3
1-2-2 Operation Panel ...............................................................4
1-3 For Piling Sheets .......................................................................5
2. Operation Procedure ............................................... 7
This section explains setting up each parts and operation procedure.
2-1 Operation Procedure .................................................................8
2-2 Irregular Size Sheet Folding .....................................................12
2-3 Cross Fold/12-Page Letter Fold ................................................15
2-4 When Folding Is Not Even or Square .......................................19
2-4-1 To correct uneven fold ....................................................19
2-4-2 To correct not square fold ...............................................20
3. Trouble Shooting ..................................................... 21
This section shows quick reference of trouble which can be resolved
or prevented by operator.
3-1 Trouble Shooting ......................................................................22
4. Maintenance ............................................................. 25
This section explains maintenance for PF-P310.
4-1 Feed Roller/Double Feed Stop Pad Replacement .....................26
4-2 Fold Roller Replacement .......................................................... 28
4-3 Removal of Jammed Sheet........................................................30
4-4 Count Sensor Cleaning .............................................................31
4-5 Maintenance Kit (Option) .........................................................32
4-6 Option .......................................................................................32

IV

1. Before You Begin
1
1. Before You Begin
This section explains machine parts and their function.
1-1 Specifications ......................................................................................... 2
1-2 Machine Parts Descriptions.................................................................. 3
1-3 For Piling Sheets.................................................................................... 5

1. Before You Begin
2
1-1 Specifications
Maximum Sheet Size : A3 (11" x 17")
Minimum Sheet Size : 65 mm x 44 mm (2.6" x 1.7")
Stock Weight : 50 to 105 gsm
Folding Speed : 140 sheets /min (A4, single fold)
Maximum Pile Height : 21 mm (0.85")
Power : 100 v 50/60 Hz (65 w)
(Power Consumption) : 115 v 50/60 Hz (65 w)
: 230 v 50 Hz (65 w)
Fold Patterns : Single Fold, Short Fold, Parallel Fold
: Letter Fold, Accordion Fold, Gate Fold
Dimension (W x D x H) : 711 mm x 485 mm x 316 mm (28" x 19.1" x 12.5")
Machine Weight : 29 kg (64 lb)
The machine design and specifications are subject to change without any notice.

1. Before You Begin
3
Support Roller
Holds sheets for smooth
feeding.
Feed Guide
Guides sheet for straight
feeding.
Power Switch
Used to turn ON/OFF main
power.
Feed Tray Lever
Used to lower feed tray for
piling, to raise for folding.
Feed Tray
Used to pile sheets to be
folded.
Feed Roller
Feeds piled sheet to buckle
section.
Delivery Tray
Folded sheet is delivered
to this tray.
Stopper Position Indicator
Used to indicate position of
stopper with lamps.
Stopper Handle
Used to move stopper.
1-2 Machine Parts Descriptions
1-2-1 General View

1. Before You Begin
4
1-2 Machine Pars Description
1-2-2 Operation Panel
Clear Button
Used to clear display.
Display
Indicates number of
folded sheets.
Sheet Size Select Button
Used to select sheet size.
Sheet Size Lamp
Indicates sheet size. Test Feed Button
Used to feed one sheet for
testing.
Start/Stop Button
Used to start/stop folding.
Fold Pattern Lamp
Used to indicate fold pat-
tern selected.
Fold Pattern Select Button
Used to select fold pattern.

1. Before You Begin
5
- Fan well the sheet before piling on the
feed tray. Otherwise, double sheet feed-
ing or miss feed occur.
- Make sure that printed ink is dry enough.
Otherwise, double sheet feed will occur.
The wet ink will not only be stain the
printed sheet but also make lower the
precision of folding of this machine.
- Jog well the sheet before piling on the
feed tray. Otherwise, jamming or miss
feed or fold on edge of sheet will occur.
- Straighten up the curled sheet or
folded sheet.
1-3 For Piling Sheets

1. Before You Begin
6

2. Operation Procedure
7
2. Operation Procedure
This section explains setting up each parts and operation procedure.
2-1 Operation Procedure............................................................................. 8
2-2 Irregular Size Sheet Folding .............................................................. 12
2-3 Cross Fold/12-page Letter Fold ......................................................... 15
2-4 When Folding Is Not Even or Square ............................................... 19

2. Operation Procedure
8
PF-P310
PEPER FOLDER
PEPER FOLDER
Feed Tray
Delivery Tray
1.Plug power cord to outlet.
2.Open delivery tray and feed tray.
3.Turn on power switch.
4.Lower feed tray lever.
2-1 Operation Procedure
Feed Tray Lever

2. Operation Procedure
9
Feed Tray
2-1 Operation Procedure
5.Pile sheets on feed tray.
- Face printed surface downward.
- Jog well and true up sheets toward feed
roller.
- Place sheets center of feed tray.
6.Slide both feed guides so that feed
guides slightly touch piled sheets.
- Place support rollers at 10 mm inside of
sheet edge.
7.Select sheet size with sheet size select
button.
NOTE
When irregular size sheets are folded, refer
to "2-2 Irregular Size Sheet Folding" (Page
12 to 14).
8. Selectfolding pattern with folding
pattern select button.
Feed Guide
Support
Roller

2. Operation Procedure
10
ストッパの移動方向
ストッパの移動方向
L
S
S
L
1
1
ストッパ
ストッパ
Orange
Mark
Lamp
2-1 Operation Procedure
9.Turn stopper handle so that orange mark
aligns with the illuminated orange lamp.
10.
Raise feed tray lever.
11.
Press test button to fold one sheet in
order to check folding accuracy.
12. Check
folded sheet.
NOTE
- If sheet is folded uneven, correct it with
referring to "Adjustment Chart" on top
cover of PF-P310. Or refer to "2-4 When
Folding is not Even or Square" (page 19 to
20).
- Press test feed button and check folded
sheet after adjustment.
Stopper Handle
Stopper Handle
11"x17"
8
1/2
"x11"
6"x9"
5
1/2
"x8
1/2
"
Adjustment Chart

2. Operation Procedure
11
13.
Press start/stop button. PF-P310 starts
folding.
14.
When you want to stop folding, press
start/stop button or lower feed tray lever.
15.
Number of folded sheets are indicated
on display.
- To delete display, press clear button.
- Number indicated on display is deleted
also when power switch is turned off.
16.
When your folding job is finished,
lower feed tray lever and turn off main
switch.
- Pull out power cord from outlet.
- Close delivery tray and feed tray.
11"x17"
81/2"x11"
6"x9"
51/2"x81/2"
2-1 Operation Procedure

2. Operation Procedure
12
2
1
二つ折
二つ折
片袖折
片袖折
S L
内三つ折
内三つ折
四つ折
四つ折
S L
0
5
ABC
ABC
ABC
Printed Surface
Downward
ABC
1
Printed Surface
Downward
二つ折
二つ折
片袖折
片袖折
S
内三つ折
内三つ折
四つ折
四つ折
S L
0
5
ABC
ABC
2-2 Irregular Size Sheet Folding
1.Fold one sheet by hands in your re-
quired fold pattern in order to make a
model.
2.Measure size of folding edge with ruler
and set stopper.
[ How to measure size of folding edge and
how to pile sheets ]
1 = length (position) for stopper 1
2 = length (position) for stopper 2
is printed side.
Single Fold (Buckle 2 is not used.)
Parallel Fold
Appearance of delivered Sheet
Appearance of delivered Sheet

2. Operation Procedure
13
1
2
ABC
ABC
ABC
Printed Surface
Upward
1
観音折
観音折
ABC
ABC
2
ABC
Printed Surface
Downward
1
2
ABC
ABC
ABC
Printed Surface
Downward
1
2
ABC
ABC
ABC
Printed Surface
Downward
Letter Fold
Accordion Fold
Gate Fold
2-2 Irregular Size Sheet Folding
1 = length (position) for stopper 1
2 = length (position) for stopper 2
is printed side.
Short Fold
Appearance of delivered Sheet
Appearance of delivered Sheet
Appearance of delivered Sheet
Appearance of delivered Sheet

2. Operation Procedure
14
03PFP310A70
Stopper Handle 2
Stopper Handle 1
2-2 Irregular Size Sheet Folding
3.Complete step 1 to 6 in "2-1 Operation
Procedure" (Page 8 to 9) and select
folding pattern with folding pattern
select button.
4.Set stopper.
- Set stopper 1 to the length 1.
- Set stopper 2 to the length 2.
- Start folding with referring to "2-1 Op-
eration Procedure" step 10 through 16
(Page 10 to 11).
Table of contents
Other Standard Horizon Folding Machine manuals