Stanley Hugs CGS-HGS-1000 User manual

User Guide
Hugs®Wi-Fi Tag Charger

iii
Hugs® Wi-Fi Tag Charger User Guide
Table of Contents
Introduction 1
Overview 1
Model Numbers 1
Intended Use 1
Safety Considerations 1
Documentation 1
Orientation 2
General Description 2
Operating and Display Modes 5
Installing the Charger 6
Wall Mounted 6
Setting Up the Charger 7
Using the Charger 8
Inserting the Tag into the Charger 8
Removing the Tag from the Charger 9
Specific Charging Capabilities 10
Overview 10
Dimensions and Weight 10
Hugs Tags States 11
Hugs Tag Behavior with Sensor Alarm 12

iv Hugs® Wi-Fi Tag Charger User Guide
Maintenance 13
Operational Checks 13
Cleaning Instructions 13
Supplies and Accessories 15
Compliance and Safety 16

Introduction
1
Hugs® Wi-Fi Tag Charger User Guide
Introduction
Overview
The Hugs on MobileView software notifies the users when the Hugs Tag
battery is getting low. Placing the Hugs Tag in the charger erases all the
history data from the tag, including the Kisses® bonding and the tag
status. It also triggers MobileView to erase the specific patient admitting
information.
Model Numbers
The Hugs Tag Charger part number:
• CGS-HGS-1000
Based on the power supply outlet type:
• CGS-HGS-1000-U U.S. outlet
• CGS-HGS-1000-E European outlet
• CGS-HGS-1000-J Japanese outlet
• CGS-HGS-1000-UK U.K. Outlet
Intended Use
The Hugs Wi-Fi Tag Charger is intended for facility staff who are using the
Hugs Wi-Fi Tags in conjunction with the MobileView security application.
Safety Considerations
• Position any trailing wires so that they are not a trip hazard and are less
likely to get damaged.
• Check that the plug is not damaged and that the cable is properly
secured with no internal wires visible.
• Where there is evidence that the supply may not be safe, such as
damaged equipment or wiring, the supply should not be used until work
has been done to correct this.
Documentation
Please refer to the following document for technical specifications for the
Hugs Wi-Fi Tag Charger.
• Hugs Wi-Fi Tag Charger Data Sheet p/n 0971-063-000

Orientation
2Hugs® Wi-Fi Tag Charger User Guide
Orientation
General Description
This section describes the parts and LEDs on the Charger. POWER
SOCKET
ON/OFF
SWITCH
CHARGER
STATUS
CHARGING
LED
CHARGING
METALS
Power Socket
The power socket is located at the top-left side of the Charger. An external
power supply is provided with the Charger. For more information about the
power supply, see “Supplies and Accessories” on page 15.

Orientation
3
Hugs® Wi-Fi Tag Charger User Guide
Orientation
General Description
This section describes the parts and LEDs on the Charger. POWER
SOCKET
ON/OFF
SWITCH
CHARGER
STATUS
CHARGING
LED
CHARGING
METALS
Power Socket
The power socket is located at the top-left side of the Charger. An external
power supply is provided with the Charger. For more information about the
power supply, see “Supplies and Accessories” on page 15.
ON/OFF Switch
After the Charger is plugged in, press the ON/OFF switch to the ON position.
When the Charger is not being used, press the switch to the OFF position.
Charger Status LED
The Charger status LED is located at the top-right on the front of the
Charger. When the Charger is plugged in and turned on, the Charger status
LED turns YELLOW.

Orientation
4Hugs® Wi-Fi Tag Charger User Guide
Charging LED for Hugs Tag
CHARGING LED:
Yellow when the Hugs Tag
is correctly placed in the
Charger
Each Hugs Tag impression in the Charger has its own charging LED (24
LEDs in total). There are three (3) available colors for the LEDs: GREEN,
YELLOW and RED. For more information about the LED color indications, see
“Operating and Display Modes” on page 5.
Charging Metals
The charging metals are located on either side of the inside of the Hugs Tag
impression. Charging for the Hugs Tag only begins once the charging metals
are in contact with the metal in the tag slots

Orientation
5
Hugs® Wi-Fi Tag Charger User Guide
Operating and Display Modes
The following table describes the LED indications for the Hugs Tag Charger.
Color Description
GREEN Battery is fully charged.
YELLOW Charging in progress.
RED FLASHING Issue with the Hugs Tag. Remove and replace the tag.
RED SOLID Issue with the Charging slot. It is not necessary to unplug the
Charger. An error may possibly be cleared by switching the
Charger OFF then back ON again. If the issue continues, do not
use the specic Charging slot. Other slots can be used for charging.
Please contact Support.
OFF - NO COLOR LED is does not turn on when the tag is placed in the slot– Remove
the tag and replace it with a dierent tag. If the LED is still o, place
the tag in another charging slot. If the LED is on (GREEN or AMBER) in
the new slot then the problem is with the rst charging slot. Do not
use this slot to charge tags. If the LED in the new charging slot is o
as well, then there is an issue with the tag. Discard the tag.
YELLOW Located near the ON/OFF switch indicating the Charger is ON.

Installing the Charger
6Hugs® Wi-Fi Tag Charger User Guide
Installing the Charger
The following items are included with the Hugs Tag Charger:
• two (2) #6 Philips head screws
• two (2) plastic wall anchors
• Mounting plate
Wall Mounted
1. Establish a location on the wall for the Hugs Tag Charger.
2. Draw two (2) holes on the wall, at a level distance 262 mm apart,
from center to center.
3. Drill two holes at the marked locations on the wall.
4. Insert the plastic wall anchors in the drilled holes.
5. Mount the plate and align the anchor holes with the wall anchors.
6. Using the supplied Philips head screws, securely screw the plate to
the wall.
7. Optionally, use wood screws or other suitable wall mount hardware
in the remaining holes on the plate.
8. Slide the Hugs Tag Charger onto the plate to mount it on the wall.