EcoSolaris ECO-LIGHT Solar LED Batten Light Kit User manual

USER MANUAL
Ecosolaris ECO-LIGHT Solar LED Batten Light
Kit
100% Green
Energy
Rechargeable
Lithium Battery
PIR Motion
Sensor
IP65 Rated
Waterproof
5V USB
Charge
Integrated
Design
WHAT IS IT?
ECO-LIGHT is an innovative model of solar powered tube light. It can be used in many
applications, such as office, home, garage, caravan, carports, warehouses, camping tents,
kinds of shelves, farm tents, sideways, emergency camps, aid tents, any types of sheds, etc.
The ECO-LIGHT solar led batten light kit contains everything, like rechargeable lithium
battery, solar controller, and the solar panel. The installation is easy and can be done in less
than 15 minutes. You just need to plug solar panel into the light with the DC connector. It
provides a high brightness for long time continuous lighting output and the inbuilt PIR
sensor allow to save power if sunshine is not strong enough.
This solar LED batten light can also work during daytime while being charged, under manual
operation. By programming the remote control, you can increase or decrease the brightness
as you like. 2 hours, 4 hours and 6 hours lighting modes can be selected. By pressing the
button on the fluorescent tube, you can select one of the 3 lighting modes. The brightness
and duration of lighting may be set with the remote control.
One 5V USB output was added to charge your mobile. What’s more, an external switch is
allowed to be connected to this light via a DC port. The ON/OFF and brightness can be
operated by hand just like the traditional lights. This is a very useful feature when it is
necessary to control lighting manually rather than automatically.
In conclusion, the ECO-LIGHT solar LED batten light is the ultimate lighting solution for
remote locations without power or light
ACCESSORIES
1. Push Button (100% power / 50% power / 30% + sensor 100% / OFF).
2. USB 5V 1A Output (To charge mobile or other device).
3. DC input connector to connect to (6) plug to wall switch.
4. DC input to charge connector for solar panel 6V input (Warning : do
not use other device or solar panel to charge).
5. Motion sensor (Two options on remote: 0% + 100% for 24 hours;
30% + 100% for 12 hours).
6. Wall switch for extension control (same function as push button (1)).
CONNECTION DIAGRAM
WALL SWITCH
Wall Switch is a very useful components in this kit.
You can use this useful solar light fixture in the same
way of using a 120V normal light.
1st push : 100% power
2nd push : 50% power
3rd push : 30% when nobody there and go to 100%
power when sensor is triggered
4th push : Light OFF
(These 4 working programs are looped)
REMOTE CONTROL
MANUAL – switch ON/OFF, 100% full power
AUTOMATIC – ON/OFF up dawn & dark, 100% power
Increase the brightness by 20%
Decrease the brightness by 20%
Light is 0% (off power)
Turn ON when the sensor is triggered
Light is ON with 30% power and 100% when sensor is triggered
Set light to work for 2 hours
Set light to work for 2 hours
Set light to work for 6 hours
PACKAGING CONTENT :
Solar Batten Light 1 piece
Solar Panel + 5m cable + 2 brackets 1 piece
Wall Controller + 4m cable 1 piece
Remote Control 1 piece
Fixing dowels and SST304 screws 1 piece
User manual 1 piece
ADVANTAGES :
1. ON/OFF mode Night & Day (works manually day and night).
2. 130 degree motion detection area.
3. Manual dimmer mode
4. Timer mode : Turns ON/OFF automatically after 2H, 4H or 6H.
5. Automatic Mode : Working from dusk to dawn automatically.

Remarkll
1. When installation is completed, the batten light will start to work under automatic
mode as default setting.
2. Manual mode allows daytime operation. In manual mode, light will turn OFF after 12
hours if not turned OFF manually.
3. If the red light flashes once when you try to turn it ON, it means the battery is dead.
Make sure you charge it properly
INSTALLATION
HOW TO REPLACE BATTERY
SPECIFICATIONS
Size
L
ED
max
M
ax
lumens
Batter
y
Solar
panel
C
a
ble
IP Rate
360 mm 12W 1200 lm 3,7V
8,8
A
h
10W
6V
5,0 m IP 65
600 mm 24W 2400 lm 3,7V
17,6
A
h
18W
6V
5,0 m IP 65
For any additional information request or for any
problem with the product, please contact us
before returning it.
CONTACT INFORMATION :
Ecosolaris
622, Roland-Godard Blvd
Saint-Jerome (Quebec)
J7Y 4C5
1-800-966-7987
[email protected]
www.ecosolaris.com
3. Use 3mm hexagon
spanner to loose and
remove the two screws
1. Drill the hole for screws.
Screw diameter is 4 mm
2. Insert the screw cap into
wall and make it flat as
surface
3. Use screw driver to fix
the screws into the
wall/ceiling
4. Connect light and solar
panel with the DC solar
cable
5. Press button to turn ON
light
1st push: 100% power
2nd push: 50% power
3rd push: 30% power +
100% when sensor is
triggered
4th push : OFF
6. Disconnect the DC
connectors then take
out the battery carefully
1. Remove the bracket
from the side where there
are no buttons
2. Use clips or small tools
to take out the two
silicone plugs
4. Separate the end cap
from tube body (avoid
losing the waterproof
silicon ring)
5. Hold the battery cable
and take it out carefully
from light fixture until
you see the DC
connectors
7. Hold the cable
connector from light, and
insert battery properly,
then connect battery
cable to light cable by DC
connectors.
8. Put the end cap back
to tube body with silicon
wing at good position
9. Repeat the steps of last
operations
6 -> 5 -> 4 -> 3 -> 2 -> 1.
Tip : When new battery is connected to controller
successfully, the red light inside of motion sensor will start
ON for 2 seconds, then OFF.
6. Select AUTO or MANUAL
mode and set the lighting
program as you like
IMPORTANT
NOTE:
If your batten light does not light up during
daytime, please deactivate Automatic Mode
by pressing the ‘‘Auto’’ button on your
remote control.