Saxby Lighting 72641 Manual

Instruction leaflet
Sight Recessed
72641
Live Voltages may be present in this unit even when turned of or when completely disconnected.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Safety information
Cleaning Information
wash
with warm water or just use a damp cloth. finish.
Check with your Local Authority or retailer for recycling advice.
Recycling advice
This bulb is protected by a shade. This part must be replaced immediately should the shade become
cracked or damaged. This fitting must not be used without the shade in place.
lit for the three hour period, a new battery pack may be
required.
fully discharge then reconnect to supply and allow to
charge for 24 hours.
change the battery pack as follows:
Undo the two screws holding the front diffuser in place.
Remove the diffuser and set aside.
should not be disposed of with household waste. Please
recycle where facilities exist. Check with your local
authority or retailer for recycling advice.
Replace the battery with a 3.6V 1500mAh Ni-Cd
ONLY. Use of a different type of battery will damage the
product.
secure battery in position and then plug battery pack
connector into the PCB.
to trap any wires.
Refit the diffuser. Tighten the screws carefully to avoid
damaging the threads.
Restore power and allow to charge for 24 hours.
Battery Replacement
www.saxbylighting.com Saxby Lighting. BH23 3PE
V2 14/02/2020
WWW.saxbylighting.com Saxby lighting. BH17 7BY
Replace Cracked Shade

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure other
persons cannot restore the electrical supply without your
knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the
connections.
This product is not suitable for dimming.
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
These products should not be fitted to PIR circuits or short
duration timed switches.
This product is rated IP20.
Specification
Layout
Wiring
Check that...
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection
block.
Voltage: 240V ~ 50Hz
IP rating: 20
Operating Temperature : -5˚C to 50˚C
Change over Time: Approximately 1s
Battery Specification: 3.6V 1500mAh Ni-Cad
Battery Charge Time: 24 hours
Battery warranty: 2 years
Maintained Wiring:
Having correctly identified the wiring from your existing light fitting, unscrew the two securing screws on the tabs inside the
fitting and flip down the gear tray. Pull the wire through the hole and connect to the connection block inside the product in
the following way:
lit all the time and in the event of a power failure will
remain on. The unit will charge automatically.
that the source is
batteries are charging.
supply, the battery has not been connected properly or
the internal circuit may have failed.
three months.
lamp in emergency mode checked every six months.
Operation
Existing fittings must be completely removed before
installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
screws and cover and set aside.
is 200mm.
needed, then file the hole until the recessed unit fits
snugly.
on the back casing of the product for supply of cable.
detailed overleaf.
Installation
recess, turn product to correct position and rest onto
metal side tabs. is now ready for use.
Commissioning
Fitting/replacing bulbs
PERMANENT LIVE (BROWN)
NEUTRAL (BLUE)
EARTH (GREEN/YELLOW)
SWITCHED LIVE
NEUTRAL TERMINAL
LIVE TERMINAL
EARTH TERMINAL
SUPPLYLIGHT FITTING