Eddylight EDD-RP-WBIF1006 User manual

EDD-RP-WBIF1006
USER MANUAL

1. Introduction
2. Safety Information
3. Photos and Specifications
4. Main Function
5. 5. Rear Panel Display and Operation
6. Instructions for Manual
Programming
7. Master/Slave Control
8. Cable Connection

1. Introduction
Thank you for purchasing our EDD-RP-WBIF1009 Cube light. Please read
these instructions carefully before operating to avoid any possible damage
and accidents caused by misuse.
The Cube light has a hydrodynamic aluminum shell. Five integrated, high-
brightness LED lights (containing red, green, blue, amber, white) are used
to create a wide spectrum of colors. Each red, green, blue, amber and
white color can be independently mixed, dimmed, faded and so on. It
draws low power and is low weight, and is remote controllable. The DMX
controls include dimming, fade, strobe, gradual change and more. The unit
is compatible with the standard DMX 512 signal for external DMX control.
Practical uses of the product include dance halls, stage backgrounds,
hotels and drapery uplighting.
Packing List
- EDD-RP-WBIF1009 Cube light
- Power cable
- Remote control
- User manual
2. Safety Information
- Please consult skilled service technicians for any repairs required
- Always disconnect from the power source before setting up, moving and
servicing
- Avoid direct eye contact to the light when in operation
- Make sure the power supply voltage is compatible with this light
- Before installation, please check the light’s fasteners and mechanical
structure is in good condition and not damaged
- The light is designed for indoor use, below 40 degrees celsius
- The fixture may be mounted in any position provided there is adequate
room for ventilation. Make sure there are no flammable and explosive
items within 0.5 meters.
- Please ensure the ground is always connected
www.eddylight.com 1-800-914-3538

3. Photos and Specifications
Input Voltage: AC 100V - 260V, 50-60Hz
LEDs: 6 X 10W R/G/B/A/W 5-in-1 LEDs
Battery Spec: 15,600 mAH,11.1 VDC
Battery Life: (full brightness, all colors on) >8 hours
Recharger Output voltage: 12.6 V, 3A
DMX Channels: 5 or 9CH
Control Mode: Standalone, Mater/slave, Auto, Sound Active
Wireless: 2.4G
IR: Infrared remote control up to 30 ft./10m
Function Effect: Dimmer, Strobe, Color Changing, Sound Activation
Refresh Rate: 1.5KHz. Flicker free operation (No flickering on camera)
Beam Angle: 25°
Cooling Mode: Natural convection
Protection Grade: IP20
Anti-electricity Intension: >1.5KV
Insulation Resistance: >2MΩ
Dimensions: 6.58” x 5.43” x 7.28”
Weight: 8.16 lbs

4. Main Function
5 Channel Mode:
Channel
DMX
Value
Function
Notes
1
0-255
Red dimming
0—100%
2
0-255
Green dimming
0—100%
3
0-32
Blue dimming
0—100%
4
0-255
Amber dimming
0—100%
5
0-255
White dimming
0—100%
9 Channel Mode:
Channel
DMX
Value
Function
Notes
1
0-255
Red dimming
0—100%
2
0-255
Green dimming
0—100%
3
0-32
Blue dimming
0—100%
4
0-255
Amber dimming
0—100%
5
0-255
White dimming
0—100%
6
0-255
Master dimmer
7
15-255
Strobe speed
8
196-255
Built-in programs
Overrides CH1-7
9
28-127
Dimmer mode
(See “nodE” in MENU)
9
128-250
Color fading
Overrides CH1-8
9
251-255
Sound activation
Overrides CH1-8
www.eddylight.com 1-800-914-3538

5. Rear Panel Display and Operation
MENU: Access the menu or return to a previous menu option
UP: Menu selection or parameter increments
DOWN: Menu selection or parameter increments
ENTER: Select the current menu option
6. Instructions for Manual Programming
MENU items:
•"”Addr”: DMX mode (001-512)
•“Slav”: Slave mode
•"“Chnd”: DMX channel mode (5CH/9CH)
•"“SouA”: Sound activated mode
•"”SP”: Built-in program speed change mode (speed = 0-15)
•“Pr”: Built-in preset programs (0-11)
•"”Colo”: Preset colors (0-30)
•“Strb”: Strobe mode (speed = 0-15)
•"”r”: Solid color mode, red setting (0-255)
•"”g”: Solid color mode, green setting (0-255)
•"”b”: Solid color mode, blue setting (0-255)
•”a”: Solid color mode, blue setting (0-255)
•"”w”: Solid color mode, white setting (0-255)
Press ENTER to save your selection, which means you will enter the
menu mode saved previously when you activate the light next time. For
example, if you want to choose DMX mode d017, operate as follows:
(See next page)
LED Display
Selection buttons
DMX input/output
DMX OUT DMX IN
Menu Up Down Enter

•Press MENU repeatedly until “Addr”
•Press UP / DOWN to select your desired address (ie. “d017”)
•Press ENTER to choose.
Creating Solid Colors: (r, g, b)
•Press MENU until “r”, “g”, “b” is selected.
•Press UP / DOWN until to change the number (brightness of that color)
•Press ENTER to choose
•Repeat the process for each color, including amber and white
Sample colors:
Color
Name
Red
Green
Blue
Amber
White
"
Red
255
0
0
0
0
"
Green
0
255
0
0
0
"
Blue
0
0
255
0
0
"
Amber
0
0
0
255
0
"
White
0
0
0
0
255
"
Yellow
255
255
0
0
0
"
Magenta
255
0
255
0
0
"
Cyan
0
255
255
0
0
"
Champagne
0
0
0
255
255
"
Cold White
255
255
255
0
0
"
Warm White
255
255
255
255
255
www.eddylight.com 1-800-914-3538

7. Master/Slave Control
The MASTER functions as a master as long as it’s not in DMX mode (and
ideally no cable plugged into the DMX INPUT on the unit). It sends a
signal to the SLAVE through a DMX cable and synchronizes its settings to
it. Do not use more than 20 lamps or 60m of DMX cable.
The SLAVE units should be set to DMX mode and the address code set to
“A001” to receive the MASTER’s signal. Only one light can be set as a
master, but multiple lights can be set as slaves.
8. Cable Connection
A standard XLR connection is used for the DMX 512 protocol:
DMX512 does not include automatic error checking and correction, and so
is not an appropriate control for hazardous applications, such as
pyrotechnics or movement of theatrical rigging. False triggering may be
caused by electromagnetic interference, static electricity discharges,
improper cable termination, excessively long cables, or poor quality
cables.
If using 5-pin DMX, please use a 5-pin to 3-pin cable adapter. Details on
configuration below:
Note: In order to avoid failures and
signal interference, it is recommended
to connect a 120Ωresistor (1/4W) at the
end of the DMX connection as shown on
right. If using 5-pin DMX, please use a
5-pin to 3-pin cable adapter. Details on
configuration below: