Star Micronics DP8340R Series User manual

Dot Matrix Printer
DP8340R SERIES
[
SERIAL INTERFACE
]
USERS MANUAL

Federal Communications Commission
Radio Frequency Interference
Statement
is equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. is equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.
is statement will be applied only for the printers marketed in U.S.A.
Statement of
e Canadian Department of Communications
Radio Interference Regulations
is Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
e above statement applies only to printers marketed in Canada.
Trademark acknowledgments
DP8340: Star Micronics Co. Ltd.
Notice
•All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s
express permission is forbidden.
•e contents of this manual are subject to change without notice.
•All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to
press. However, should any errors be detected, STAR would greatly appreciate being informed of them.
•e above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 1986-2008 Star Micronics Co., Ltd.

TABLE OF CONTENTS
1. OUTLINE........................................................................................... 1
2. UNPACKING AND INSTALLATION ............................................. 2
2-1. Unpacking............................................................................................. 2
2-2. Installation of Paper Holders and Re-Roll
Prevention Guard ................................................................................ 3
2-3. Handling Notes .................................................................................... 4
2-4. Maintenance......................................................................................... 5
3. PART IDENTIFICATION AND NOMENCLATURE..................... 6
3-1. Power Supply Unit............................................................................... 6
3-2. Printer ................................................................................................... 7
3-3. Part Functional Description............................................................... 8
4. INSTALLATION OF INK RIBBON AND PAPER .......................... 9
4-1. Installation of Ink Ribbon................................................................... 9
4-2. Removal of Ink Ribbon..................................................................... 10
4-3. Paper Insertion................................................................................... 11
4-3-1. For Roll Paper ..............................................................................11
4-3-2. Roll Paper Installation
(When using the optional Printer Cover 8340R)....................12
4-3-3. Validation Option Installation...................................................13
4-4. Roll Paper Removal ........................................................................... 13
5. CONTROL CODES ......................................................................... 14
6. GENERAL SPECIFICATIONS ....................................................... 15
7. INTERFACE FOR MODEL DP8340RM
MODULAR JACK CONNECTOR......................................................... 19
7-1. Interface Specications ..................................................................... 19
7-2. Interface Circuit................................................................................. 19
7-3. Setting of the DIP Switches .............................................................. 20
7-3-1. DIP-SW 1......................................................................................20
7-3-2. DIP-SW2.......................................................................................20
7-4. Connectors and Signals..................................................................... 21
7-5. Interface Connections....................................................................... 22
7-6. Peripheral Unit Drive Circuit........................................................... 23
7-6-1. Cable Connection........................................................................23
7-6-2. Peripheral Drive Circuit .............................................................24
7-6-3. Control Codes..............................................................................24

8. INTERFACE FOR MODEL DP8340RD
DSUB 25 PIN CONNECTOR ..................................................... 25
8-1. Interface Specications ..................................................................... 25
8-2. Interface Circuit................................................................................. 26
8-2-1. RS-232C ........................................................................................26
8-2-2. Current Loop................................................................................26
8-3. Setting of the DIP Switches .............................................................. 27
8-3-1. DIP-SW 1......................................................................................27
8-3-2. DIP-SW 2......................................................................................27
8-4. Jumper Setting.................................................................................... 28
8-4-1. Removal of the Bottom Cover ...................................................28
8-4-2. Setting of Jumper.........................................................................28
8-5. Connectors and Signals..................................................................... 29
8-6. Interface Connections....................................................................... 30
8-7. Peripheral Unit Drive Circuit........................................................... 31
8-7-1. Cable Connection........................................................................31
8-7-2. Peripheral Drive Circuit .............................................................32
8-7-3. Control Codes..............................................................................32
9. DATA STRUCTURE AND CONTROL.......................................... 33
9-1. DTR Mode (1 BLOCK)..................................................................... 33
9-2. X-ON/X-OFF Mode.......................................................................... 34
9-3. STX-ETX Mode ................................................................................. 36
10. CHARACTER CODE LIST........................................................... 38
11. WHEN POWER IS SUPPLIED BY THE USER........................... 41

– 1 –
1. OUTLINE
e DP8340R series of serial dot matrix printers is for use in ECR, POS, elec-
tronic instruments, banking machines and computer peripheral equipment.
e DP8340R series include the following features;
1) 2 color printing (Red and Black)
2) High-speed bidirectional printing (2 line/sec, 29 or 44 columns per line)
3) 9-pin print head
4) The interface conforms to RS-232C in M type, and to RS-232C/20mA
Current Loop in D type.
5) Commands for expanded characters, inverted characters, emphasized
characters, red and black printing, and 10CPI or 15CPI characters etc. are
provided, which makes the printer very versatile.
6) Simultaneous Data Communication and Printing
7) Error Checking Protocol
8) Peripheral Driver
9) One line validation printing (Option)
Model Name Notation
DP8340 R M
Interface
Printer Type
D: D-sub 25 Pin Connector
( RS-232C / 20mA Current Loop )
M: Modular Jack Connector
( Only RS-232C )
R: R Type Printer
(3.25 inch paper)

– 2 –
2. UNpackINg aNd INsTaLLaTION
2-1. Unpacking
Aer opening the box, check if all necessary accessories are included.
(A) Printer
(B) Power Supply Unit (Option: PS8340A)
Figure 2-1. Unpacking
1Printer
2User’s Manual
3Paper Holders
4Re-Roll Prevention Guard
5Ink Ribbon
6DIP Switch Cover
1Power Supply Unit
2User’s Manual
1

– 3 –
2-2. Installation of Paper Holders and Re-Roll Prevention Guard
Install the Paper Holders in the intermost holes in the rear of the printer.
Figure 2-2. Installation of Paper Holders
Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting the
Wire as shown in the gure below, will make the installation easier.
Figure 2-3. Installation of Re-Roll Prevention

– 4 –
2-3. Handling Care
1. Be careful not to drop paper clips, pins or other foreign matter into the unit
as these cause the printer to malfunction.
2. Do not attempt to print when either paper or ribbon cartridge is not located
in the printer, otherwise the print head can be damaged.
3. Do not open the cover while printing.
4. Do not touch the print head immediately aer printing as it gets very hot.
5. Use only roll paper that is not glued to the core.
6. When the paper end mark appears on the paper, replace the roll paper before
it runs out.
WARNING
PShut down your equipment immediately if it produces smoke, a strange
odor, or unusual noise. Immediately unplug the equipment and contact
your dealer for advice.
PNever attempt to repair this product yourself. Improper repair work can be
dangerous.
PNever disassemble or modify this product. Tampering with this product
may result in injury, re, or electric shock.
PDuring and immediately aer printing, the area around the print head is
very hot. Do not touch it, as you could be burned.
CAUTION
P
We recommend that you unplug the printer from the power outlet
whenever you do not plan to use it for long periods. Because of this, you
should locate the printer so that the power outlet it is plugged into is
nearby and easy to access.
P
If the voltage shown on the label on the of your printer does not match the
voltage for your area, contact your dealer immediately.
P
Make sure that the printer is turned o and unplugged from the AC outlet
and that the computer is turned o before making connections.
P
Do not connect a telephone line into the modular connector.
PDo not pull out paper while the printer cover is closed.
PIf liquids, foreign objects (coins and paper clips), and so on enter the
printer, turn o the printer, unplug it from the AC outlet, and contact your
dealer for advice. Continued use could cause a short circuit, which may
result in re or electric shock.

– 5 –
2-4. Maintenance
Essentially, your printer is a robust piece of equipment, but should be treated
with a modicum of care in order to avoid malfunctions. For example:
1. Keep your printer in a “comfortable” environment. Roughly speaking, if you
feel comfortable, then the environment is suitable for your printer.
2. Do not subject the printer to physical shocks or excessive vibration.
3. Avoid over-dusty environments. Dust is the enemy of all precision
mechanical devices.
4. To clean the exterior of the printer, use a cloth barely dampened with either
water with a little detergent or a little alcohol, but do not allow any liquid to
fall inside the printer.
5. The interior of the printer may be cleaned with a small cleaner or a
compressed-air aerosol (sold for this purpose). When performing this
operation, be sure not to bend or damage any cable connections or electronic
components.

– 6 –
3. parT IdENTIfIcaTION aNd NOmENcLaTUrE
3-1. Power Supply Unit (Option)
Model name : PS8340A
Input : 100 to 240V AC, 50/60 Hz 6.0A
Output : DC12V 5% 2.0A
Figure 3-1. Power Supply Unit
DC Power Connector (Output)
Shape of AC Power plug will
vary according to destinations.

– 7 –
3-2. Printer
Figure 3-2. Printer: Front View
Figure 3-3. Printer: Rear View
Do not connect this to a
telephone.

– 8 –
3-3. Part Functional Description
(1) AC Power Plug : Connect to an outlet of the specied voltage.
(2) DC Power Outlet : Supplies DC 12V power to the printer.
(3) Printer Cover : Protects the printer against dust and reduces noise.
(4) POWER Lamp : Lights up (green LED) when power is on.
(5) ON LINE Lamp : Lights up (green LED) when the unit is in the online
mode.
(6) ALARM Lamp : Lights up (red LED) when printer operation is not
normal, or the printer is out of paper. It is necessary
to install paper into the printer and press the ON
LINE Button to recover from paper empty status.
Turn o the printer power in order to recover from
abnormal operation.
(7) ON LINE Button : Toggles between the on-line and off-line modes.
e printer will go on-line aer turning power on.
(8) FEED Button : Momentary operation of this button provides one
line feed. Pressing this button continuously will
cause continuous paper feed. If power is turned on
while pressing this button, self printing*1 will be
performed.
(9) Interface Connector : Connects the printer to host computers. Check that
both computer and printer are o before connect-
ing.
(10) DIP Switches : Allows for setting of various functions according to
user requirements.
*1 Self Printing is printer has another convenient function, the
Automatic Test Printing. With the ink ribbon and
paper properly installed in the printer, turn the pow-
er ON while holding down the Feed switch. Test
printing will start and stop again automatically.

– 9 –
4. INsTaLLaTION Of INk rIbbON aNd papEr
4-1. Installation of Ink Ribbon
(1) Turn power o, li the Printer Cover up and remove it.
Note: Be careful not to touch the print head immediately after printing,
because it can get very hot.
Figure 4-1. Printer Cover Removal
(2) Unwind ribbon so that the spools are separated as shown in Figure 4-3.
Hold the ribbon taut as shown with the drive pins facing down and slide the
ribbon between the print head and the platen. While keeping the ribbon
taut, wrap one side around the black ribbon guide on the end of the platen
and drop one spool on the spool sha. As you move the spool downwards,
move the detecting lever aside to allow the spool to drop into place. Make
sure the spool drive pins engage with the spool drive holes. As the spool
drops into place there will be a click.
(3) While continuing to hold the ribbon taut, install the remaining ribbon spool
in a similar fashion.
(4) Turn the spool that rotates freely to take up the ribbon slack.
Ribbon Life
Description Ribbon life
Black Red
SF-03BR Approx. Approx.
0.8 million characters 0.4 million characters

– 10 –
Figure 4-2. Installation of Ink Ribbon
Figure 4-3. Ribbon Spools
4-2. Removal of Ink Ribbon
Hold the spool and li gently, rotating it until the ribbon sags. Push the ribbon
detecting lever out, li the spool until it comes o the sha. Remove the second
spool in a similar manner.
(Do not apply excessive force when liing spools.)
Ribbon Life
Description Ribbon life
Black
Approx.
SF-03B 0.8 million characters

– 11 –
4-3. Paper Insertion
4-3-1. For Roll Paper
(1) Cut the Roll Paper end straight and square. Hold the roll so that the paper
comes from the bottom.
(2) Attach the Roll Paper to the Holders Paper by slipping one side of the roll
onto the Hub and pulling the other Hub out to allow the roll to slip in place.
(3) Insert the paper evenly into the Paper Insertion Slot.
(4) Turn the Power Switch “ON”, and press the FEED Button. e paper will be
fed into the unit.
Figure 4-4. Paper Insertion (1)
Figure 4-5. Paper Insertion (2)

– 12 –
4-3-2. Roll Paper Installation (When using the optional Printer Cover 8340R)
When installing roll paper with the optional “Ptinter Cover 8340R”, please use
the following procedure.
(1) Turn power o, li the Printer Cover up and remove it.
Note: Be careful not to touch the print head immediately after printing
because it can get very hot.
(2) Insert paper into the printer, and feed the paper so it extends 3 inches or
more above the top surface of the printer.
(3) Insert the paper into the slot in the “Printer Cover 8340R”.
(4) Install the “Printer Cover 8340R” on the printer.
Figure 4-6. Replace the Printer Cover
Figure 4-7. Printer Cover 8340R

– 13 –
4-3-3. Validation Option Installation
e validation printing requires the optional printer cover 8340R. Refer to item
4-3-2 for the installation.
(1) Turn power ON.
(2) Enter the printer the validation mode.
(Refer to the control code “GS” in Chapter 5.)
(3) Insert the material to be validated against the right side of the slot in the
Printer Cover 8340R.
Figure 4-8. Insertion of Material to be validated
4-4. Roll Paper Removal
Cut the paper close to the slot and use the feed button until paper has passed
completely through the printer.
Note: Do not try to remove the paper by hand as it could become crooked and
get jammed inside the printer.

– 14 –
5. cONTrOL cOdEs
Character Code List
Character Code Function
1 LF (0A)H Print and line feed instruction
2 CR (0D)H Print and line feed instruction
(same as LF)
3 SO (0E)H Expanded character instruction
4 DC4 (14)H Expanded character release
5 ESC-1 (1B)H (2D)H(01)H Underline instruction
(1B)H (2D)H (31)H
6 ESC-0 (1B)H (2D)H(00)H Underline release
(1B)H (2D)H (30)H
7 SI (0F)H Inverted print instruction
8 DC2 (12)H Inverted print release
9 ESC E (1B)H (45)H Emphasized print instruction
(one-way printing)
10 ESC F (1B)H (46)H Emphasized print release
11 ESC 4 (1B)H (34)H Red character print instruction
12 ESC 5 (1B)H (35)H Red character print release
13 ESC a n (1B)H (61)H n n-line feed instruction
14 ESC C n (1B)H (43)H n Sets page length in lines
1 n 120 (default n = 42)
15 ESC N n (1B)H (4E)H n Set bottom margin in lines
0n 120 (default n = 0)
16 ESC O (1B)H (4F)H Cancel Bottom margin
17 FF (0C)H Form feed
18 ESC @ (1B)H (40)H Printer initialization instruction
19 ESC BEL (1B)H (07)H Set peripheral unit drive pulse duration
n1n2n1n21 n1127, 1 n2127
(default n1= n2= 20)
20 BEL (07)H Trigger peripheral unit drive (Deferred)
21 FS (1C)H Trigger peripheral unit drive
(Immediate)
22 ENQ (05)H Enquiry
23 STX (02)H Start of text enter STX-ETX mode
24 ETX (03)H End of text end STX-ETX mode
25 CAN (18)H Clears print buer
26 ESC P (1B)H (50)H Select 10 CPI
27 ESC M (1B)H (4D)H Select 15 CPI (Default value)
28 GS (1D)H Validation printing instruction

– 15 –
6. gENEraL spEcIfIcaTIONs
Printing method : Serial impact dot matrix printing,
9 wires
Number of print columns : 29 columns (10CPI), 44 columns (15CPI)
Print speed : Approx. 2 lines/sec
Print direction : Bi-directional
Line spacing : 1/6 inch
Paper feed method : Friction Feed
Paper feed speed : Approx. 12 lines/sec
Character set : ASCII 96 characters
Special 64 characters
Block graphics* 64 characters
Font conguration : 10CPI Ordinary characters 5 ×9 dots
Block graphics* 6 ×6 dots
15CPI Ordinary characters 7 ×9 half dots
Block graphics* 5 ×6 dots
* Graphic Feed Not Available
Character size : 10CPI 2.00 (H) ×2.42 (V) mm
15CPI 1.32 (H) ×2.42 (V) mm
Character spacing : 10CPI 2.55 mm (1/10 inch)
15CPI 1.70 mm (1/15 inch)
Dot spacing : 10CPI H=0.425 mm V=0.353 mm
15CPI H=0.340 mm V=0.353 mm
Gross dot : 10CPI 174 dots/wire/line
15CPI 220 dots/wire/line
Print area : 10CPI 73.53 mm
15CPI 74.46 mm
Print Buer : Approx. 1.5 KB
Peripheral drive : 1 output (1A max. at 12V)
Serial Interface :
Model DP8340-RM Only RS-232C
Model DP8340-RD RS-232C/20mA Current Loop
External dimensions :
(Printer) 202(W) ×200(D) ×98(H) mm
(without paper holder, DC Power Connector)
(Power supply unit) 54(W) ×114(D) ×36(H) mm (without AC cable)
Weight :
(Printer) Approx. 1.9 kg
(Power supply unit) Approx. 0.3 kg (without AC cable)

– 16 –
Power supply unit :
Four supplies available with following ratings
Input Output
AC 100 to 240 V DC 12.0 V ±5%
50/60 Hz
0.6 A 2.0 A
Paper specication :
Paper type Ordinary and carbonless copy paper
Size Paper width 82.55 ±0.5mm (3.25 inches)
Roll diameter 80 mm outer diameter (Max)
ickness (single) 0.07 mm (52.3 g/m2) to 0.09 mm (64g/m2)
(2 copy) One copy and one original (max 0.13 mm)
Paper end Paper should not be attached to the core
One line validation Check (Refer to Fig. 6-2)
Paper width 70 to 90 mm
ickness 0.1 to 0.15 mm
* Requires the optional Printer Cover 8340R
Ink ribbon specication :
Color Black and red / Black only
Ribbon material Nylon (#40 denier)
Ribbon size 13mm ×6m
Spool 13mm (width), 35mm in diameter (two spool)
Recommended ribbon SF-03BR (Black and red), SF-03B (Black)
Operating conditions : Temperature +5˚C to +40˚C
Humidity 10% to 80%RH
Storage conditions : Temperature –20˚C to +70˚C
Humidity 5% to 95%RH (+40˚C)
Head life : 70 million characters
Printer reliability : 5.0 million lines MCBF (except head life)