StarTech.com MDP2DPDVHD User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: March 28, 2019 12:58 PM
Product Diagram (MDP2DPDVHD)
Component Function
1DVI-D Connector • Used to connect a DVI-D Display Device to the
Video Adapter.
2HDMI Port • Used to connect a HDMI Display Device to the
Video Adapter.
3DisplayPort Port • Used to connect a DisplayPort Display Device
to the Video Adapter.
4Mini DisplayPort
Connector
• Used to connect the Video Adapter to the
Host Computer.
Requirements
For the latest requirements, please visit www.startech.com/MDP2DPDVHD.
• DisplayPort enabled computer system with available Mini
• DisplayPort connector
• DisplayPort, DVI or HDMI enabled display device (e.g. monitor) with appropriate
cable
Mini DisplayPort to DisplayPort, DVI or HDMI™ Multifunction Adapter
1
Installation
1. Connect the Mini DisplayPort Connector on the Video Adapter to the Mini
DisplayPort port on the Host Computer. The Host Computer can be turned on or
o check documentation for the Host Computer for details).
2. Power on the Display Device.
3. Connect the Display Device (i.e. monitor) to the Video Adapter using the
appropriate type of video cable (not included).
NOTE: Only one video output is supported on the video adapter at a time. If multiple
connections are made, only one of the outputs will function in order of: DisplayPort
then HDMI then DVI.
Specications
Video Signal • DisplayPort
• DVI-D (Digital)
• HDMI
Connectors • Mini DisplayPort male x 1
• DVI-D 25-pin female x 1
• HDMI x 1
• DisplayPort female x 1
Maximum Video Resolution • DisplayPort 2560x1600
• DVI/HDMI 1920x1200
Enclosure Material • Plastic
Operating Temperature • 0°C ~ 70°C (32°F ~ 158°F)
Storage Temperature • -10°C ~ 80°C (14°F ~ 176°F)
Humidity • 10% ~ 85% RH
Integrated Cable Length • 150mm / 0.5ft
Dimensions (LxWxH) • 79.0mm x 50.0mm x 16.0mm
Weight • 64g
2
3
4

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.