StarTech.com TB310G2 User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support
Manual Revision: February 2, 2023 11:44 AM
Product Diagram (TB310G2)
Front View
Component Function
1Thunderbolt 3 Host
Port
• Connect to a Thunderbolt 3 compatible Host
Computer
2LED Indicator
• Solid Blue = Indicates if the Thunderbolt 3 to
Ethernet Network Adapter is linked to the Host
Computer
Rear View
Thunderbolt 3 to 10GBase-T Ethernet Network Adapter
Component Function
1LED Indicators
• Left LED Indicator is Link Speed
• Solid Green = 10 Gbps
• Solid Amber =
5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps
• Right LED Indicator is Link Status
• Solid Green = Active link
• Flashing Green = Activity
2Ethernet Port • Connect an Ethernet Cable
Use Cat6 or better cabling for 10 Gbps speeds
Package Contents
• Ethernet Network Adapter x 1
• 27.5 in (70 cm) Thunderbolt 3 Cable x 1
• Quick-Start Guide x 1
Requirements
For the latest manuals, product information, technical specications, and declarations of
conformance, please visit: www.startech.com/TB310G2
• Thunderbolt 3 compatible host computer
• Ethernet Cable
Operation
Thunderbolt 3 Host
1. Connect a Thunderbolt 3 Cable (included) to the Thunderbolt 3 Host Port on the
front of the Thunderbolt 3 Ethernet Network Adapter and to a Thunderbolt 3
Port on the Host Computer.
Note: Driver installation is not required.
Windows Thunderbolt Approval Pop-Up
When the Thunderbolt 3 Ethernet Network Adapter is connected to a Host
Computer that is running a Windows operating system a pop-up message will appear.
To use the Thunderbolt 3 Ethernet Network Adapter, complete the following:
1. In the New Thunderbolt devices have been connected pop-up message, click OK.
2. In the User Account Control pop-up message, click Yes.
1
1
2
2
*Product may vary from image

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modications not expressly approved
by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 0.5cm between the radiator and your
body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or
symbols of third-party companies not related in any way to StarTech.com. Where they occur these references
are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other
protected names and/or symbols contained in this manual and related documents are the property of their
respective holders.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or
agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots,
loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR
À DÉPOSER
EN MAGASIN À DÉPOSER EN DÉCHÈTERIE
OU
FR
Cet appareil,
ses accessoires,
cordons et piles
se recyclent
3. In the Approve Thunderbolt Devices pop-up message, do one of the following:
a. To authorize the Thunderbolt 3 Ethernet Network Adapter each time a
connection is established, select Connect Only Once in the drop-down list.
b.To authorize the Thunderbolt 3 Ethernet Network Adapter once, select Always
Connect in the drop-down list.
4. Click OK.
macOS
1. No drivers or additional steps are needed to use the Thunderbolt 3 Ethernet
Network Adapter in macOS.