StarTech.com 410VDSLEXT2 User manual

Manual Revision: 12/18/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
410VDSLEXT2
1 Port to 4 Port 10/100Mbps VDSL2 Ethernet Extender
Kit over Single Pair Wire – 1 km
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Product Overview ..................................................................................2
Installation .............................................................................................4
Hardware Installation ............................................................................................................................. 4
DIP Switch Settings - Transmitter ........................................................5
Conguration..........................................................................................7
Web Interface ............................................................................................................................................. 7
Welcome Screen........................................................................................................................................ 7
System........................................................................................................................................................... 8
Port Management..................................................................................................................................... 11
VLAN .............................................................................................................................................................. 14
QoS Setting ................................................................................................................................................. 16
Security Filter.............................................................................................................................................. 19
VDSL Setting ............................................................................................................................................... 20
Connector Architecture ......................................................................................................................... 22
Resetting Your Device.............................................................................................................................. 23
Appendix...................................................................................................................................................... 23
Technical Support ..................................................................................25
Warranty Information............................................................................25

Instruction Manual
ii

Instruction Manual
1
Introduction
Packaging Contents
• 1x 1 Port VDSL2 Ethernet Transmitter
• 1x 4 Port VDSL2 Ethernet Receiver
• 2x Universal Power Adapters (NA/UK/EU)
• 1x RJ45 to VDSL2 Cable
• 1x RJ11 Cables
• 1x Instruction CD
• 1x Instruction Manual
System Requirements
• 10/100 Mbps Ethernet Network
• Available AC electrical outlets
• RJ11 Cable or RJ11 lines in building infrastructure

Instruction Manual
2
DC Input
LED Indicators
LED Indicators
RJ11/RJ45 VDSL
Line Port
RJ11 VDSL Line Port
RJ45
Ports
DC Input
Reset
Receiver Unit
Transmitter Unit
DIP
Switch
RJ45 Port
Transmitter Unit
Receiver Unit
Product Overview
Front / Side View
Rear View

Instruction Manual
3
LED Displays
Transmitter Unit
LAN LED Display
LED Blinking ON OFF
1Activity Link up Link down
2100 Mbps 10 Mbps
3Full duplex Half duplex
VDSL LED Display
LED Blinking ON OFF
1Activity Device
Power On
Device Power O
2-CPE Mode CO Mode
3Slowly: Idle
Quickly: Training Linked Oine
LED Blinking ON OFF
PWR Device Power
On
Device
Power O
SYS System Activated System
Running
CO CO Mode On
CPE CPE Mode On
LINK
Activity
Slowly: Start Connection
Quickly: Data Transmit
Linked
ALM Connection Error
Receiver Unit

Instruction Manual
4
Installation
Hardware Installation
Transmitter Unit
1. Connect the provided power adapter from an AC electrical outlet to the DC Input on
the Transmitter Unit. The “PWR” LED should light up solid.
2. Set all four of the DIP switches to the upward (OFF) position. This places the unit in
CO mode.
3. Connect an RJ45 Ethernet cable to the RJ45 LAN Port on the Transmitter Unit.
4. Connect the other end of the Ethernet cable into your Ethernet network device (eg:
switch, Ethernet modem).
5. Connect an RJ11 phone cable into the VDSL Port on the Transmitter Unit.
6. Connect the opposite end of the RJ11 cable to the DSL Port on the Receiver Unit (or
to your buildings RJ11 phone line infrastructure, depending on your setup).
Optional: Congure DIP switches 2 through 4 as necessary (see “DIP Switch Settings”
section below).
Receiver Unit
1. Place the Receiver Unit at the end-point location.
2. Connect the provided power adapter from an AC electrical outlet to the DC Input on
the Receiver Unit. The “PWR” and “SYS” LED should light up solid.
3. If not previously completed, connect the RJ11 cable that was inserted into the RJ11
VDSL Port on the Transmitter Unit directly to the DSL Port on the Receiver Unit (or
from your buildings existing RJ11 analog telephone wiring, depending on the setup
from step 6 above.
4. If the Transmitter and Receiver Units are able to successfully communicate with each
other, the “LINK” LED should light up solid.
5. Connect each computer or Ethernet networking device to an available RJ45 Port
on the Receiver Unit. The respective “LAN” LED on each individual RJ45 Port should
light up to indicate a successful physical connection.

Instruction Manual
5
DIP Switch Settings - Transmitter
The Transmitter Unit has a 4-position DIP switch for conguration of Side, Channel,
Rate Limit, and SNR.
For initial setup, DIP switch 1 is usually set to the upward (OFF) position, ensuring the
unit is set to CO mode (Receiver Unit set to CPE mode by default).
When using the 410VDSLEXT2, one end (Transmitter or Receiver) must always be set to
“CO” mode, while the opposite end must always be set to “CPE” mode.
Setting each unit to CO or CPE mode is usually based on which direction you want
the most bandwidth delivered. “Download” bandwidth, data sent from CO to CPE, is
generally higher than “Upload” bandwidth from CPE to CO.
• If you need higher bandwidth from the Transmitter Unit to the Receiver Unit, set DIP
switch 1 to the upward (OFF) position.
• If you need higher bandwidth from the Receiver Unit to the Transmitter Unit, set DIP
switch 1 to the downward (ON) position.
See the “Conguration Mode Select” section below to set the Receiver Unit to the
appropriate CO or CPE mode based on the mode that was set on the Transmitter Units
DIP Switch setting.
Pin 1 - CO, CPE Switch
OFF:If Pin 1 is in the OFF position, the Transmitter Unit will operate in Central Oce
(CO) mode.
ON: If Pin 1 is in the ON position, the Transmitter Unit will operate in Customer Premise
Equipment (CPE) mode.
Pin 2 - Interleave Noise Protection

Instruction Manual
6
Pin 4 - General Protection
OFF: If Pin 4 is in the OFF position, the Transmitter Unit will operate with a SNR ratio up
to 9 dB.
ON: If Pin 4 is in the ON position, the Transmitter Unit will operate with a SNR ratio of
6 dB.
OFF: If Pin 2 is in the OFF position, the Transmitter Unit will operate in Interleave mode,
with communication protection for up to 250ms of impulse noise with latency less
than 6 ms
ON: If Pin 2 is in the ON position, the Transmitter Unit will operate in Fast mode, with
direct data transmissions having less than 1ms of latency.
Pin 3 - Band Plan
OFF: If Pin 3 is in the OFF position, the Transmitter Unit will operate in Symmetric
mode, with both downstream and upstream transmissions operating on the G.997
band plan.
ON: If Pin 3 is in the ON position, the Transmitter Unit will operate in Asymmetric mode,
with asymmetric short range transmissions operating at the highest available line rate.