StarTech.com HD2VID2 User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Product Diagram (HD2VID2)
Port/LED Function
1Composite LED • Indicates that video is connected using the
HDMI Port.
2Composite Video Port
(Yellow)
• Used to connect a Display Device to the
Converter.
3Stereo Port L/R (Red/
White)
• Used to connect an Audio Device to the
Converter.
4PAL/NTSC Switch • Used to toggle between PAL and NTSC video
modes.
Port/LED Function
5DC/5V Port • Used with the Universal Power Adapter to
power the Converter.
6Power LED • Indicates that the Converter is receiving
power.
7HDMI Input Port • Used to connect a Video Source Device to the
Converter.
HDMI® to Composite Video Converter with Audio
1
Requirements
For the latest requirements, please visit www.startech.com/HD2VID2.
Note: All Required items are sold separately.
• HDMI Enabled Video Source x 1
• Composite Video Enabled Display Device (e.g. Monitor, Projector, HDTV, etc.) x 1
• HDMI Cable x 1
• RCA Composite Video Cable x 1
• Phillips Head Screwdriver x 1
• Composite Audio Cable x 1
Installation
Note: Power o all devices before connecting the Converter.
1. Connect an HDMI Cable to the HDMI Port on the Converter and connect the other
end of the HDMI Cable to the HDMI port on the Video Source Device.
2. Connect an RCA Composite Cable (sold separately) to the Composite Video Port
on the Converter and connect the other end of the RCA Composite Cable to the
composite video port on the Display Device.
3. If HDMI audio is being used, connect Composite Audio Cables (sold separately)
to the Stereo Port L and R Ports on the Converter and the other end of the
Composite Audio Cables to the Speakers/Audio Receiver.
4. Connect the Universal Power Adapter to the DC/5V Port on the Converter and
other end to an AC Electrical Outlet. The Power LED will light up solid.
5. Power on the Video Display Device and the HDMI Video Source.
6. Slide the PAL/NTSC Switch to adjust the video mode to either PAL or NTSC.
Connecting a Regional Power Clip
1. Select a Regional Power Clip.
2. Align the two Side Tabs on the Regional Power Clip with the notches on the face
of the Universal Power Adapter.
3. Slide the Regional Power Clip down until you hear a click, connecting the contact
prongs on the Regional Power Clip with the contact prongs on the Universal
Power Adapter.
24
3
5 6 7

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall it be the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or
agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Supported Resolutions
Description
Video
• Input Resolutions:
• HD: 1080p, 720p, 576p, 480p @ 60Hz
• PC: 1280x800, 1280x768, 1224x768, 800x600, 640x480 @ 60Hz
• Output Resolutions:
• 480i (NTSC) @ 3.58MHz
• 576i (PAL) @ 4.43MHz
Removing a Regional Power Clip
1. Push the Release Button on the Universal Power Adapter.
2. Slide the Regional Power Clip upward, aligning the Side Tabs on the Regional
Power Clip with the notches on the Universal Power Adapter.
3. Pull the Regional Power Clip away from the Universal Power Adapter.
Installing the Mounting Brackets
1. Align a Mounting Bracket with the two Mounting Holes on the side of the
Converter.
Note: The Converter has four Mounting Holes, two on each side.
2. Insert the Bracket Screws (x2) through the Mounting Bracket and into the
Mounting Holes.
3. Tighten the Mounting Screws using a Phillips Head Screwdriver, be careful not to
overtighten.
4. Before installing the Mounting Bracket onto the mounting surface, contact a
professional. Product mounting should be completed by a certied professional as
per the local safety and building code guidelines.