StarTech.com PEXHDCAP60L User manual

Manual Revision: 11/28/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
PEXHDCAP60L
HDMI®/DVI/VGA/Component PCIe
Capture Card – 1080p/60fps
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Software Installation................................................................................................................................ 8
Software Operation ...............................................................................10
How to Use ..............................................................................................11
Stream Catcher .......................................................................................11
Launch Application .................................................................................................................................. 11
Technical Support ..................................................................................25
Warranty Information............................................................................25

Instruction Manual
1
Product Diagram
DVI input-port
A/V breakout cable input-port
(For component, S-Video, and composite video input +
RCA audio input)

Instruction Manual
2
Introduction
Packaging Contents
• PCIe capture card (PEXHDCAP60L)
• HDMI to DVI adapter
• VGA to DVI adapter
• Component A/V breakout cable
• S-video/Composite A/V breakout cable
• Full-prole bracket (Attached)
• Low-prole bracket
• Software installation disc
• Instruction manual
System Requirements
• Low-prole or full-prole Computer system with:
Available PCI-Express slot
CPU: i3 Dual core 2.8GHz or higher
RAM: 2GB or higher
Microsoft® Windows® 2000/XP/Server 2003/Vista/Server 2008 R2/7/8/8.1 (32/64-bit)
• HDMI/DVI/VGA/Component/S-Video/Composite audio/video source with cabling
(DVD, DVR, VCR, Etc.)
Note: The USB3HDCAP product will not record digitally encrypted content.

Instruction Manual
3
Hardware Installation
1. Determine which bracket is required for your computer system. If you have a full-
prole computer system, attach the Full-prole bracket. If you have a low-
prole computer system attach the Low-prole bracket. To change the bracket
follow the below steps:
a) Using a small ratchet, or pliers (not included), remove both of the DVI-port stando
screws located on the outside of the bracket.
b) Using a Philips head screw driver (not included), remove the screw located next to
the internal side of the DVI-port on the circuit board.
c) You can now remove the undesired bracket by pulling the bracket away from the
PEXHDCAP60L.
Installation

Instruction Manual
4
d) Line up your desired bracket so that the DVI input-port, and the A/V breakout cable
input-port align with the port holes. Also ensure the screw hole is aligned with the
underside of the PEXHDCAP60L.
e) Using a Philips head screw driver (not included), replace the screw located next to
the internal side of the DVI input-port on the circuit board.

Instruction Manual
5
f) Using a small ratchet, or pliers (not included), replace both of the DVI-port stando
screws by placing them into the stando holes located on either side of the
DVI input-port.
g) The bracket has now been replaced.
2. Install the PEXHDCAP60L in your computer system.
a) Turn o your computer system and disconnect any peripheral devices (i.e.
Printers, external hard drives, etc.). Unplug the power supply power cable from
the rear of the computer system.
b) Remove the case cover from your computer system (See documentation
included with your computer system for step by step instructions).

Instruction Manual
6
c) Locate an open PCI-Express slot and if necessary remove the metal cover
plate on the rear of your computer case (See documentation included with your
computer system for step by step instructions).
Note: The PEXHDCAP60L will work in a PCI-Express slot with additional lanes (i.e.
x4, x8 or x16 slots)
d) Gently insert the card into the open PCI-Express slot and fasten the bracket to
the rear of the case.
e) Place the case cover back onto the computer system.
f) Reconnect any peripheral devices, as well as the computer system power supply.
3. Using the required cabling (not included), connect your desired audio/video
source device to the PEXHDCAP60L.
a. If your audio/video source device is Component or S-Video/composite use
the included corresponding Component A/V breakout cable or S-Video/
composite A/V breakout cable to connect your Audio/Video source cabling to
the A/V breakout cable input-port on the PEXHDCAP60L.
Component A/V breakout
cable
S-Video/composite A/V breakout
cable

Instruction Manual
7
b. If your video source device is DVI, connect your video source cabling directly
to the DVI input-port on the PEXHDCAP60L.
c. If your video source device is VGA or DVI, use the corresponding included
HDMI to DVI adapter or VGA to DVI adapter to connect your audio/video
source cabling to the DVI input-port on the PEXHDCAP60L.
d. (Optional) If you would like to capture a 2-channel RCA audio source along with
your video source, connect your RCA audio source cabling to A/V breakout
cable input-port using the S-video/composite A/V breakout cable along with
your desired video source cabling.
DVI
HDMI
OR
VGA

Instruction Manual
8
4. Hardware installation has now been completed. You can now turn on your
computer system.
Software Installation
Note: After the card has been installed for the rst time, your computer system
may display the Found New Hardware wizard upon boot. If this message is
displayed click cancel.
1. Download the latest software from the StarTech.com website (recommended)
or
Insert the included Driver and Software installation disc into your DVD-ROM drive.
2. Locate and run the Setup(.exe) application. This le will be located in the main le
directory.
Note: If using the included Software installation disc, the software may begin
automatically.

Instruction Manual
9
3. The Driver installation program will being. If a Windows Security dialog window
appears, click the “Run” or“Install this driver software anyway” option to proceed.
4. The installation wizard will now walk you through the installation steps for all drives
and software installation as well as ask you to specifying your desired language.
You will be prompted to conrm installation and continue the installation process
several times. Please follow the on screen Prompts, selecting armatively to each in
order to complete the software Installation.

Instruction Manual
10
5. When prompted click Finish
Note: You will be required to restart your computer.
Software Operation
1. Upon starting Windows, if the “Found New Hardware” wizard appears on the screen,
cancel/close the window and insert the included Driver CD into the computer’s CD/
DVD drive.
2. AutoPlay should automatically prompt you to run “Setup.exe”. If not, open “My
Computer” and double-click on the CD/DVD drive. Double-click the “Setup.exe” icon.
3. Proceed through the Installation wizard.
4. Complete the wizard and this should automatically install all necessary
driverssoftware. An icon for “StreamCatcher” should now be on the desktop.

Instruction Manual
11
How to Use
Connect the video/audio source to the video capture card using the
appropriatecable(s). To connect a VGA source, use the included DVI to VGA adapter.
If you wish toinput audio from a source other than HDMI, make sure to connect the
breakout cable and connect the audio source using stereo RCA cables (red/white).
Stream Catcher
Launch Application
Double-click the “StreamCatcher” icon on the desktop to launch the video capture
application. This will bring up the main menu screen that contains the video preview
window and recording controls. Additional options and congurations can be
accessed through the Main Menu.
Initial Setup Note: If you have a video source connected, but are not able to view
anything in the video window, go to the “Settings” section rst, to make sure the
“device”is congured properly. If using an HDCP protected video source (i.e. retail
Blu-Ray movie), this will also result in no video preview/capture.

Instruction Manual
12
Menu
Record/Stop
Button
Snapshot
Button
Volume
Control
Video
Window
Manually recording video can be done by simply pressing the “Record” button from the
control menu along the bottom of the Stream Catcher window. The frame around the
video window will turn red, while recording. When you would like to to stop recording,
press the “Stop” button. The “Snapshot” button allows of taking a screen capture of the
video stream.

Instruction Manual
13
Snapshot Files
Clicking this button will open the folder location where all of the snapshot les are
saved in Windows.
Record Files
Clicking this button will open the folder location where all of the recorded video les
are saved in Windows.

Instruction Manual
14
Schedule Recording
The software can be setup to start recording at a specic time and date and occur once
or multiple times. Setup the schedule and click the “Add” button to save it. Multiple
schedules can be maintained at the same time. To remove a schedule, simply select it
from the list, and click the“Delete”button.
Settings
The Settings menu is broken into dierent sections for conguring various aspects of
the software. System Settings contains conguration options for the user interface.

Instruction Manual
15
Device Settings
The Device Settings contains conguration options for the video capture hardware.
Video and audio input source (HDMI, component, DVI/VGA), video system (NTSC/PAL),
aspect ratio and video properties (sharpness, contrast, saturation, hue, brightness) can
all be adjusted from this menu.
Record Settings
Contains settings related to video recording and snapshots. The location to save
recorded video les as well as recording quality can be congured. The location to save
the snapshot images and le format (JPG, BMP) are also set here.

Instruction Manual
16
Video Streaming
Streaming using RTMP Streaming Service Provider
1. Obtain the RTMP settings for your video streaming service. The below steps show
how to obtain these settings from Justin.TV and Twitch.
Note: Steps may vary from dierent streaming service providers, please contact
your service provider for specic details.
For Justin.tv
1. Open your web browser, and browse to the following website:
http://www.justin.tv
2. Login and select Dashboard from manager your account.
3. Select My Channel from the left side menu, followed by INFO.

Instruction Manual
17
4. In the lower section of this page, you will nd Steam Key: Show Click Show, you will
see the key.