StarTech.com ATX2PW400PRO User manual

Manual Revision: 01/25/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ATX2PW400PRO (400 Watt)
ATX2PW450PRO (450 Watt)
ATX2PW500PRO (500 Watt)
ATX2PW550PRO (550 Watt)
Professional 450W ATX Computer Power
Supply with PCIe & SATA
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Features ........................................................................................................................................................ 1
Package Contents ..................................................................................................................................... 1
Installation ..............................................................................................2
Specications..........................................................................................4
DC Output.................................................................................................................................................... 5
Technical Support ..................................................................................6
Warranty Information............................................................................6

Instruction Manual
1
Introduction
This 450 Watt ATX12V 2.01 power supply oers a professional-grade PC power solution,
with support for modern Intel and AMD dual-core CPU designs as well as PCI Express
and SATA device connections.
Compliant with ATX12V 2.01 revision standards, the power supply oers dual 12V
power rails and ensures broad compatibility with a 20/24 pin motherboard connection.
Designed to provide dependable, long-lasting power to your hard working AMD
or Intel CPU based system, the 450 Watt power supply features an 80mm dual ball
bearing fan to help keep the PSU cool. To ensure stable power delivery to the most
demanding devices, the power supply features Quad+1 protection against short-
circuit, over-power, over-voltage and no-load situations.
This high quality, professional-grade ATX12V 450W power supply is backed by
StarTech.com’s 3 year warranty and free lifetime technical support.
Features
• ATX 2.01 compliant, including 2 12V power rails to deliver stable power to
demanding devices; also includes a 20 pin ATX connector for compatibility with
existing standards
• 8cm fan provides superior airow for increased reliability (dual fans on 550W model)
•
Premium EMI/RFI power ltration provides low noise and ripple for stable power delivery
• Quad+1 protection against: short circuit, over power, over voltage, no load, plus
over current on both 12V rails
• Built-in protection from short circuit, over power, over voltage and no-load
situations to prevent power supply damage
• Generous number of accessory connectors and a nickel-plated nish
Package Contents
• 1 x Power supply
• 1 x Standard power cable
• 1 x Instruction Manual

Instruction Manual
2
Installation
CAUTION: Computers contain sensitive electronic components that are easily damaged
by static electricity and excessive shock. When handling the power supply and other
components, ensure you are properly grounded using an anti-static mat or similar
device. If anti-static equipment is not available, ground yourself by touching the exterior
of the computer case or another large metal surface before handling any peripherals.
1. Installation of a power supply requires some mechanical skill and requires that you
open your computer case to disconnect and reconnect wires. If you are unfamiliar
with this kind of work, consider bringing your computer and new StarTech.com
power supply to your local computer store for help.
2. Check the red switch on the rear of the power supply, next to the power cord plug.
Be sure it is set to the correct voltage for your country. In North America, it should
read“115”. In Europe and Australia it should read“230”. To change the switch, use a
screwdriver in the notch of the switch and slide it to the opposite side. If you are unsure
of the voltage used in your country, contact your electricity provider before proceeding.
3. If you are replacing an old power supply in your computer, ensure the computer is
shut down and disconnect the power cord from the back of the old supply.
4. Open your computer case. In most designs, the case is opened by removing two or
three screws at the rear of the case and then sliding the covering panel backward
until it comes free. If your case is a tower style, ensure that you remove the panel
that will expose the top of the computer’s motherboard. This is generally the left-
side panel. There are many dierent case designs, however, so if you are unsure of
how to open your particular case, consult the user manual for your case or contact
your local computer store for help.
5. With the computer case open, review the connectors being used from your old
power supply. If you are building a new computer, review the connectors that you
will need to use. Check the type of connector on your motherboard and use either
the 24 or 20 pin ATX power connector (break away the additional 4 pins on the
connector if your system uses a motherboard with a 20-pin connector).
6. Disconnect the old power supply connections from inside your computer. Hard
disk drive, CD drive and oppy disk drive connectors disconnect by pulling on the
connector. The motherboard connector(s) have a clip that must be pressed while
pulling on the connector to release them. A rocking motion while pulling will aid in
getting the connectors loose. Never pull on the wires of a connector to unplug it.
7. Check that all the wires from your old power supply are free. Remove the four
screws on the rear of your old power supply to free it from the computer case.

Instruction Manual
3
Support the power supply with one hand if it could fall while removing the last
screw. (Such as in a tower style case.) Remove the power supply by sliding it back
and then out through the side of your case.
8. Install your new power supply by positioning it through the side or top of your case
(depending on your case style) and then back onto the power supply mounts. Check
that the orientation with the screw holes in your case is correct; all four holes must be
aligned. Support the power supply with one hand while threading a mounting screw
through the back of the case and into the power supply. The screw should thread
smoothly and should not require eort. Do not force it or you could damage the
mounting holes. If the screw won’t thread smoothly, remove it and check to ensure the
mounting holes are correctly lined up. Repeat for the remaining three screws. Do not
fully tighten any of the screws until they all have been threaded into their mounting
holes. (Note: Consider Startech part SCREWTHUMB screws for easier installation.)
9. Tie unused wires away from fans and other moving parts.
10.Replace the case cover and secure it.You may wish to not replace the screws until
after you have checked that all connections are working.
11.Toggle the rear power switch on power supply to o. (The “0” symbol on the switch.)
Connect the power cord to the power supply and plug it in to a grounded power
outlet. (The power supply MUST be connected to a grounded outlet.) Toggle the
rear power switch to on.
12.Start your computer.You should hear its fans and devices immediately begin to
run. If you do not, toggle the rear switch on the power supply to o, disconnect the
power cord, open the case and check that all connectors are well seated and secure.
13.When you have conrmed all connections are working, replace the screws in your case.
14.Power supplies contain electrical and electronic components and should be
disposed of properly. If you replaced an old power supply follow your city’s rules for
proper disposal of electronic equipment.

Instruction Manual
4
Specications
Total Output: 400W 450W 500W 550W
Connectors:
LP4 4 6 6 6
SP4 2 2 2 2
20/24-
pin ATX
Motherboard
1 1 1 1
ATX 12V
4-pin 1 1 1 1
SATA Power 4 4 4 6
PCI Express 1 1 1 2
TX3 1 1 1 1
Dimensions
5.51 x 5.91 x
3.35”
140 x 150 x 86
mm
5.51 x 5.91 x
3.35”
140 x 150 x 86
mm
5.51 x 5.91 x
3.35”
140 x 150 x 86
mm
5.51 x 5.91 x
3.35”
140 x 150 x 86
mm
Weight 4.20 lbs.
(1.9 kg)
4.5 lbs
(2.0 kg)
4.5 lbs
(2.0 kg)
4.85 lbs
(2.2 kg)

Instruction Manual
5
DC Output
AC Input
115/230V +3.3V +5V +12V1 +12V2 -12V +5VSB
400W 10/5.5A 30A 28A 14A 15A 1A 2.5A
450W 10/5.5A 30A 45A 17A 16A 1A 2.5A
500W 10/5.5A 30A 45A 18A 16A 1A 2.5A
550W 12/6A 30A 50A 18A 18A 1A 2.5A

Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.