StarTech.com ATX2PW630PRO User manual

Manual Revision: 02/03/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
ATX2PW630PRO
Pro 630W ATX12V 2.3 80 Plus Computer
Modular Power Supply
*actual product may vary from photos

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
Hardware Installation .............................................................................................................................. 2
Specications..........................................................................................5
Connectors .................................................................................................................................................. 6
Technical Support ..................................................................................7
Warranty Information............................................................................7

Instruction Manual
1
Introduction
The StarTech.com Modular ATX12V 2.3/ EPS12V 2.91 series power supplies use a modular
cable design, enabling you to selectively choose the connectors you require while also
being 80 Plus®certied, thus providing stable power while balancing energy-eciency.
Compliant with ATX12V 2.3 standards, this power supply oers the versatility and
support for AMD or Intel CPU based entry level servers, gaming PCs and high end work
stations, or a higher level energy-ecient replacement/upgrade power supply for
Desktop PC’s. Featuring a 120mm fan for quieter, more ecient cooling in demanding
systems, Active Power Factor Correction and 20/24 pin motherboard support.
Packaging Contents
• 1 x ATX Power Supply
• 1 x 8-pin (6+2) PCI Express Modular cable
• 1 x 6-pin PCI Express connector Modular cable
• 1 x 3xSATA connector Modular cable
• 1 x 3xLP4 Molex + 1xSP4 oppy connector Modular cable
• 3 x Power Cord (NA/UK/EU)
• 1 x Instruction Manual
System Requirements
• ATX compliant motherboard
• ATX compliant computer case that supports full sized power supplies

Instruction Manual
2
Installation
WARNING! Computer parts can be severely damaged by static electricity. Be sure
that you are properly grounded before opening your computer case. StarTech.
com recommends that you wear an anti-static strap when installing any computer
component. If an anti-static strap is unavailable, discharge yourself of any static
electricity build-up by touching a large grounded metal surface (such as the computer
case) for several seconds.
Installation of a power supply requires some mechanical skill and requires that you
open your computer case to disconnect and reconnect wires. If you are unfamiliar
with this kind of work, consider bringing your computer and new StarTech.com power
supply to your local computer store for help.
Hardware Installation
1. Turn your computer o and any peripherals connected to the computer (i.e.
printers, external hard drives, etc.).
2. If the power supply has a power switch on it, set it to the “0” position. Unplug the
power cable from the rear of the power supply on the back of the computer and
disconnect all other peripheral cables.
3. Remove the cover from the computer case. Refer to documentation for your
computer system for details.
4. Disconnect all of the power connectors from the motherboard and peripheral
devices (i.e. hard drives, CD/DVD drives, etc). Make sure to take note of each
connector and where they were plugged in. Ensure there are no devices connected
to the existing power supply.
5. Remove the existing power supply from the computer case. This is typically done by
removing four (4) mounting screws on the outside face of the power supply. Refer
to documentation for your computer system/case for specics.
6. Connect the necessary modular cables to the power supply, in their appropriate
socket. The connectors are color coded and keyed to prevent incorrect installation.
It is only necessary to install the cables that are required for the computer system.
NOTE: The “green” Modular connector is used for PCI Express connectors while “blue” is
used for other peripheral connectors (SATA, LP4 molex, etc).

Instruction Manual
3
Peripheral Modular
connector
PCI Express Modular
connector
7. Mount and install the new power supply by reversing the steps used to remove the
old power supply.
8. Connect the power connectors from the power supply to the motherboard and
peripheral devices that were disconnected previously. Note that this power supply
uses a 20+4 pin split ATX connector, so it can be used on motherboards with either
a 20-pin or 24-pin connector. Simply detach the extra 4-pin attachment for use on
20-pin motherboards.
NOTE:
The detached4-pinconnectorcannot be usedinplace of the4-pinATX12V(P4)connector.
9. Make sure any loose or unused cables/connectors from the power supply are away
from fans and other moving parts.
10. Place the cover back onto the computer case.
11.
Make sure the power switch on the power supply is set to“0”, then insert the power cable

Instruction Manual
4
into the socket on the power supply. If the old power cable looks worn or damaged in any
way, replace with the supplied power cable, otherwise it is safe to reuse it.
12. Reconnect all other connectors/cables that were removed in Step 2.
13. Set the power switch on the power supply to “1”. The computer is now ready to be
powered up.

Instruction Manual
5
Specications
Standards ATX12V v2.3
EPS12V v2.92
Maximum Power Output 630W
Eciency Rating
85.39% @ 20% (130W)
85.29% @ 50% (323W)
80.02% @ 100% (636W)
Fans 1 x 120mm (Dual Ball Bearing)
Input Power 100 ~ 240VAC, 10 ~ 5A, 47 ~ 63Hz
Operating Temperature 0°C ~ 40°C (32°F ~ 104°F)
@ 90% Load
Storage Temperature -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 10 ~ 90% RH
MTBF 100, 000 hours
Dimensions (LxWxH) 141.0mm x 150.0mm x 86.0mm
Weight 2100g
ATX2PW630PRO Power Output
DC
Output
+3.3V +5V +12V1 +12V2 +12V3 +12V4 -12V +5Vsb
24A 24A 20A 20A 20A 20A 0.5A 2.5A
Max
Power
140W 600W 6W 12.5W
611.5W

Instruction Manual
6
Connectors
1 x ATX 20+4 pin 1 x 4+4 pin ATX12V
(8-pin EPS12V)
1 x 6-pin PCI Express 2 x 8-pin PCI Express
(6+2)
3 x 4-pin Molex Power (LP4) 1 x 4-pin Mini-Power (SP4)
6 x 15-pin SATA

Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.