StarTech.com SV831DUSBUK User manual

Manual Revision: 05/21/2021
Forthemostup-to-dateinformation,pleasevisit:www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SV431DUSBU
SV831DUSBU
SV831DUSBUK
SV1631DUSBU
SV1631DUSBUK
4/8/16 Port 1U Rack Mount VGA USB
KVM Switch with OSD
*SV831DUSBU shown

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. Regardless of any
direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
Hardware Installation .............................................................................................................................. 2
Connecting Computer to the KVM Switch....................................................................................... 2
Cascaded congurations........................................................................................................................ 3
Operation ................................................................................................4
OSD (On Screen Display) Operation................................................................................................... 5
Hot-key commands................................................................................9
Change Leading Hotkey......................................................................................................................... 11
Specications..........................................................................................14
Technical Support ..................................................................................15
Warranty Information............................................................................15

Instruction Manual
1
Introduction
The SV431DUSBU/SV831DUSBU/SV831DUSBUK/SV1631DUSBU/SV1631DUSBUK
1U Rack Mountable USB KVM Switch with OSD lets you control multiple USB based
computers from a single console (USB keyboard, USB mouse, monitor).
Convenient push-button and hot-key controls provide quick, reliable switching
between connected computers while manual and auto-scan switching modes and an
On Screen Display (OSD) oer additional control options.
Designed to ensure maximum space eciency, the USB KVM switch features a slim 1U
design that ts neatly into a server equipment rack/cabinet (with optional mounting
bracket SV431RACK) and oers rear cable connections to eliminate cable tangles and
minimize workspace disruption.
Backed by a StarTech.com 3-year warranty and free lifetime technical support
Packaging Contents
• 1 x KVM switch
• 1 x universal power adapter (NA/EU/UK/AU)
• 4 x foot pads
• 2 x rackmount brackets (8 port and 16 port only)
• 8 x 6 ft 2-in-1 USB VGA KVM cables (8 port only)
• 16 x 6 ft 2-in-1 USB VGA KVM cables (16 port only)
• 1 x screw kit (16 port only)
• 1 x instruction manual
System Requirements
• USB compatible 3 button wired mouse
• USB compatible 104-key keyboard
• VGA enable display device
• StarTech.com KVM cables
• VGA enable computer systems

Instruction Manual
2
Installation
Hardware Installation
WARNING! Prior to installation, please ensure that all computers and KVM switch(es)
are powered down.
Console Connection
The SVxxxDUSBUx series of KVM switches are designed to use USB console
connections only. A USB compatible keyboard and mouse and VGA monitor must be
used for the local console. A USB keyboard/ mouse combo device that uses a single
USB connector may also be used, but must be connected to the USB Keyboard port.
Connecting Computer to the KVM Switch
To connect a computer to the KVM switch, use the appropriate StarTech.com KVM
cable to connect from one of the PC ports located on the rear panel of the KVM switch
to the keyboard/mouse and VGA video ports on the computer
USB mouse
USB keyboard
VGA monitor
KVM
Cable
*SV1631DUSBU shown

Instruction Manual
3
Cascaded congurations
NOTE: The Master KVM switch must have equal or more PC ports than that of the Slave
KVM switches. For example, if an 8-port switch is the Master, an 8-port or 4-port switch
can be a Slave, but not a 16-port switch.
The ports labelled PC 1 - PC 8 can be connected to either a computer or a Slave KVM
switch’s CONSOLE port. On a 16-port KVM switch, the ports marked PC A - PC H can
only be connected to computers. Use only the appropriate StarTech.com KVM cables
to connect the Master KVM switch’s PC ports and Slave KVM switch’s CONSOLE port.
The maximum number of computers controlled by a Master/Slave conguration with all
8-port KVM switches used is 64, with 8 Slaves and each Slave connecting to 8 computers:
The maximum number of computers controlled in a Master/Slave conguration with
all 16-port KVM switches used is 136, with 8 units of 16-port Slaves (to PC 1 - PC 8) and
each Slave connected to 16 computers, plus 8 more computers connected directly to
the Master (to ports PC A - PC H):
After the connection has been completed, please re-activate the OSD menu to verify that
the Master recognizes the Slaves. A triangle mark ( ) is placed next to the right of the
channel name indicating that the port is connected to a Slave, not a computer. A number
to the left of the triangle mark indicates the Slave model, i.e. ‘8’for an 8-port switch.
*SV1631DUSBU shown
KVM cables
PC 4 PC 3 PC 2 PC 1
PC 5
PC 4 PC 3 PC 2 PC 1
PC 5
Slave
Slave
Master
Console
NOTE! A device (computer or KVM switch) at any ‘PC x’ port can be changed at any
time after initial power-up. If you change any one of the PC 1 to PC 8 port connections
from a computer to a Slave KVM switch or vice versa, or replace the devices of a port,
the OSD will update this change the next time it is activated.

Instruction Manual
4
Operation
You may select a computer by pressing the front panel push button directly, by
issuing hot-key commands or by activating the OSD window. The front panel indicator
changes to reect the computer port selected (red) and whether the port is connected
to a powered computer (green). The indicator ashes red when it is in either Auto Scan
or Manual Scan mode
Push Button controls
To select control of an attached computer, press the front panel button that
corresponds with the assigned computer number. For 16 port models, 1 to 8
represents the lower 8 ports, while A to H indicates the higher ports. Ports 1 and A
share the same pushbutton, as do 2 and B, 3 and C, etc.
EXAMPLE: If port 1 is already selected and you wish to switch to Port A, tap the shared
pushbutton once to select Port A. If Port 1 is not selected, press and hold pushbutton 1
for two seconds to select Port A.
K/M Reset
K/M Reset resolves the majority of problems developed by keyboard and/or
mouse device replacement or conguration changes. Press down buttons 1 and 2
simultaneously for 2 seconds to recongure the whole system without having to turn
o the KVM switch or any attached computers.
Auto Scan
This KVM switch provides an easy to use feature to start Auto Scanning. To use
this function, simultaneously press buttons 7 and 8 and hold for two seconds.
(SV431DUSBU uses buttons 3 and 4 to launch this function).

Instruction Manual
5
OSD (On Screen Display) Operation
By hitting the left <CTRL> key twice within two seconds, you may see the ’Hotkey Menu’
if it is enabled (an OSD option). Or, by hitting the left <CTRL> key three times within
two seconds, you will see a ’KVM MENU’ screen showing a list of the computers with
corresponding channel addresses, names and status.
The channel address (port number) of the currently selected computer is displayed in
red, same as the front indicator, to the right of the OSD title ’KVM MENU’.

Instruction Manual
6
The color of a device name is green if it has power and is ready for selection (its
corresponding front panel indicator is green). The color is white if it has no power. The
OSD menu updates when it is activated.
Use the <UP> and <DOWN> arrow keys to highlight a computer and the <ENTER>
key to select it. Or, you may press <ESCAPE> to exit OSD and remove the OSD menu
from the display; the status window returns to the display and indicates the currently
selected computer or operating status.
A triangle mark ( ►) to the right of a name indicates the port is cascaded to a Slave;
the number at the left of the triangle mark shows the number of ports the Slave has,
i.e. 8 for SV831DUSBU. The <ENTER> key brings you one level down and another
screen pops up listing the names of the computers on that Slave. The name of the
Slave will be shown at the upper right corner of the OSD menu. It is useful to group
computers and still be able to see the group name.
An eye mark (N) to the right of a name indicates the computer is selected to be monitored
in Scan mode. In OSD, this mark can be switched on or o by function key <F2>.
Press the <ESCAPE> key to exit the OSD and to return to the selected computer, The
computer name is also shown on the screen.
Function key <F1>: To edit the name entry of a computer or a Slave. First, use the
<UP> and <DOWN> arrow keys to highlight a channel then
press <F1> followed by name entry. Valid characters are‘A’~’Z’, ‘0’~’9’
and the dash character. Lowercase letters are converted to
uppercase ones. Press the <BACKSPACE> key to delete a letter
one at a time. Nonvolatile memory stores all name entries until
you change, even if the unit is powered down.
Function key <F2>: To switch the eye mark (N) of a computer on or o. First, use the
<UP> and <DOWN> arrow keys to highlight it, then press <F2> to
switch its eye mark on or o. If Scan Type is ’Ready PC + N’, only
the power-on and eye mark selected computers will be displayed
sequentially in Scan mode.
Function key <F3>: To lock a device (a computer or a Slave) from unauthorized access,
use Security. Security is eective for only one device (a computer
or a Slave). To lock a device, use the <UP> and <DOWN> arrow
keys to highlight it, then press <F3>. Now, enter up to 4 characters
(‘A’~’Z’, ‘0’~’9’, ‘-’) followed by <ENTER> as new password. A
Security enabled device is marked with a lock (Ï) following its
channel number. To permanently disable the security function
from a locked device, highlight it, press <F3> then enter the password.

Instruction Manual
7
If you want to access the locked device temporarily, simply highlight it and press
<ENTER>, the OSD will ask you for the password. After entering the correct password,
you are allowed to use the device. This device is automatically re-locked once you
switch to another port. During Scan mode, OSD skips the security-enabled device.
NOTE: If you forget the password, the only way to permanently erase all of the
passwords is to: For SV831DUSBU/SV831DUSBUK and SV1631DUSBU/SV1631DUSBUK,
press and hold the 1 and 2 front panel buttons, then hold 7 and 8. Release 7 and 8,
then release 1 and 2. For SV431DUSBU, press 3 and 4 instead of 7 and 8.
Function key <F4>: More functions are available by hitting <F4>. A new screen pops
up displaying more functions as described below. Most of them
are marked with a triangle ( ►) indicating there are options to
choose from. Using the <UP> and <DOWN> arrow keys, select the
functions and press <ENTER>. Available options will be shown
in the middle of the screen. Again, using the <UP> and <DOWN>
arrow keys to view options then press <ENTER> to select it. You
can press <ESCAPE> to exit at any time.
Auto Scan
In this mode, the KVM Switch automatically switches from one power-on computer
to the next, sequentially, in a xed interval. During AutoScan mode, the OSD displays
the name of the selected computer.
When Auto Scan detects any keyboard or mouse activity, it suspends the scanning
till activity stops; it then resumes with the next computer in sequence. To abort Auto
Scan mode, press the left <CTRL> twice, or, press any front button. Scan Type and Scan
Rate set the scan pattern. Scan Type (<F4>: More\Scan Type) determines if scanned
computers must also be eye mark selected. Scan Rate(<F4>: More\Scan Rate) sets the
display interval when a computer is selected before selecting the next one.
Manual Scan
Scan through power-on computers one by one by keyboard control. You can type
(<F4>: More\Scan Type) to determine if scanned computers must also be eye
mark selected. Press the <UP> arrow key to select the previous computer and the
<DOWN> arrow key to select the next computer. Press any other key to abort Manual
Scan mode.
Scan Type:
Ready PC + N:In Scan mode, scans through power-on computers and those with
the eye mark on the selected ports.
Ready PC: In Scan mode, scans through all power-on computers.
Nonly: In Scan mode, scans through any selected computer regardless of computer
power status with an eye mark.
Scan Rate: Sets the duration of a computer displayed in Auto Scan mode. The options
are 3 seconds, 8 seconds, 15 seconds and 30 seconds. The non-volatile memory stores
the Scan Rate setting.

Instruction Manual
8
Hotkey Menu: When you hit the left <CTRL> key twice within two seconds, the
Hotkey Menu appears displaying a list of hot-key commands if this option is On.
The Hotkey Menu can be turned O if you prefer not to see it when the left <CTRL>
key is hit twice. The non-volatile memory stores the Hotkey Menu setting.
CH Display:
Auto O: After you select a computer, the channel address and name of the
computer will appear on the screen for 3 seconds then disappear automatically.
Always On: The channel address and name of a selected computer and/or OSD
status displayed on the screen all the time. The non-volatile memory stores the CH
Display setting.
Position: The position of the selected computer name and/or OSD status displayed
on screen during operation. The actual display position shifts due to dierent VGA
resolution, the higher the resolution the higher the display position. The nonvolatile
memory stores the Position setting.
Upper Left, Upper Right
Middle
Lower Left, Lower Right
Country Code for Sun:
Sun keyboards of dierent languages have dierent layouts. The KVM switch is able
to emulate a Sun keyboard for a specic language type or country such as Arabic,
Belgian, US, Yugoslavia, etc. Select the proper country code that matches all of your
Sun computers.
NOTE: The country code must be set prior to powering up the Sun computer. Not
performing this step prior to power-up could cause the system to malfunction.
Max. Resolution: It supports widescreen, and you can adjust the monitor resolution
under this sub-menu. The following selections are available: 1024x768, 1280x1024,
1600x1200, 1920x1440
Widescreen resolutions: 1920x1080, 1366x768, 1280x720, 1680x1050 and“DDC2B Disable”.
Function key <F5>: To switch the Sun mark of a port on or o indicating the computer
is a Sun server as shown below. Sun servers have more keys
on the keyboard than a PC. When a Sun-marked port is selected,
the KVM Switch starts to translate the keys from a PC keyboard to
a Sun keyboard. See the section entitled Sun Keyboard Mapping
for further detail.

Instruction Manual
9
NOTE: It is unnecessary to switch the Sun mark ON or OFF if an authentic Sun
keyboard is being used on the console. In other words, you must ensure that the Sun-
marked port has not been selected if you are already using a Sun keyboard.
With dierent types of keyboard and computer, the Sun Mark must be set up in
compliance with the following instruction:
Keyboard Type Computer Type Sun Mark
USB (non-Sun) PC/Mac No
USB (non-Sun) Sun Yes
USB (Sun keyboard) PC/Mac No
USB (Sun keyboard) Sun Yes
ESC: To exit the OSD, press the <ESCAPE> key
Hot-key commands
Hot-key command is a short keyboard sequence used to select a computer, to
activate computer scan, etc. StarView interprets keystrokes followed by one or two
more keystrokes. A built-in buzzer generates a high-pitch beep for a correct hotkey
command, otherwise, one low-pitch beep for an error and the bad key sequence will
not be forwarded to the selected computer.

Instruction Manual
10
The short form hotkey menu can be turned on as an OSD function (<F4>:More\Hotkey
Menu) every time the left <CTRL> is pressed twice.
NOTE: Left <CTRL>: refers to the Control key on the left side of the keyboard.
1~8/A~H: refers to the number keys ‘1’~’8’ in the upper row of the keyboard and
character keys ‘A’ ~ ‘H’. Do not use the keypad at the right of the keyboard.
To select a computer by hotkey command, you must know its port number, which is
determined by the KVM Switch connection. For a computer connected to a Slave, two
characters represent its port. The rst character is the port number of the Master unit
(1~8) and the second one is the port number of the Slave (1~8 or A~H). Please note
that only the Master’s ‘PC1’ ~ ‘PC8’ ports can be connected to a Slave.
EXAMPLES:
Left <CTRL> , Left <CTRL>, 7 : Selects a computer connected to port 7 of the Master.
Left <CTRL> , Left <CTRL> 6, C : Selects a computer connected to port C of a Slave
connected to port 6 of the Master.
Auto Scan
In this mode, the KVM Switch automatically switches from one power-on computer
to the next, sequentially, in a xed interval. During AutoScan mode, the OSD displays
the name of the selected computer.
Left <CTRL>, Left <CTRL>, F1
When Auto Scan detects any keyboard or mouse activity, it suspends the scanning
until the activity stops. It then resumes with the next computer in sequence. The
length of the Auto Scan interval (Scan Rate) is adjustable. To abort Auto Scan mode,
press the left <CTRL> key twice.
NOTE: Scan Type determines whether an eye-marked computer is to be displayed
during Auto Scan.
Manual Scan enables you to manually switch back and forth between the
powered computers:
Left <CTRL>, left <CTRL>, F2
Press the <UP> arrow key to select the previous computer and the <DOWN> arrow
key to select the next computer. Press any other key to abort Manual Scan mode.
NOTE: Scan Type determines whether an eye-marked computer is to be displayed
during Auto Scan.
To adjust Scan Rate, which sets the duration before switching to the next computer in
Auto Scan:
Left <CTRL>, Left <CTRL>, F3
The switch will beep one to four times indicating the scan interval of 3, 8, 15 and 30
seconds respectively.

Instruction Manual
11
Change Leading Hotkey
The default leading hotkey sequence involves pressing the left <CTRL>
twice in succession (e.g. left <CTRL>, left <CTRL>). This can be changed
to the right <CTRL> key instead, to avoid accidental activation due to
using the left <CTRL> key for functions such as Copy/Paste.
To change the leading hotkey sequence to Right <CTRL>:
Left <CTRL>, Left <CTRL>, hold <ALT>, press Right <CTRL>
All hotkey commands that previously required pressing the Left <CTRL> will be
switched to requiring the right <CTRL> instead.
To change the leading hotkey sequence back to Left <CTRL>:
Right <CTRL>, Right <CTRL>, hold <ALT>, press Left <CTRL>

Instruction Manual
12
Sun/Mac Keyboard Mapping
The KVM Switch emulates a Sun Keyboard when a computer is marked with a Sun, in
the OSD menu by Function Key <F5>. A Sun keyboard has more keys than a standard
PC keyboard. These extra keys are simulated by tapping the Right <CTRL> button,
which is normally located on the right lower part of the keyboard, followed by one
of the function keys on the general keyboard (i.e. combo key). For example, tap
the Right <CTRL> key, and then tap the function key F7 to activate Open for a Sun
computer.
NOTE: For older Sun Operating Systems, the switch does not support the LowPower
option under Power O Select.
For keystroke emulation of Sun/Mac computers, please refer to chart and conduct the
following two examples:
Stop A function in Sun: Press right <CTRL> and release, then within two seconds
press F1 and A in sequence.
Help function in Sun: Press right <CTRL> and release, then within 2 seconds, press H.
From Standard Keyboard Map to Sun
Keyboard
Map to Mac
Keyboard
Press right - Ctrl and release; 1
Press right - Ctrl and release; 2
Press right - Ctrl and release; 3
Press right - Ctrl and release; 4 Power
Press right - Ctrl and release; F1 Stop
Press right - Ctrl and release; F2 Again
Press right - Ctrl and release; F3 Props
Press right - Ctrl and release; F4 Undo
Press right - Ctrl and release; F5 Front
Press right - Ctrl and release; F6 Copy
Press right - Ctrl and release; F7 Open
Press right - Ctrl and release; F8 Past
Press right - Ctrl and release; F9 Find

Instruction Manual
13
From Standard Keyboard Map to Sun
Keyboard
Map to Mac
Keyboard
Press right - Ctrl and release; F10 Cut
Print Screen F13
Scroll Lock F14
Pause Break F15
Press right - Ctrl and release; H Help
Right - Right - Right -
Left - Left - Left -
Compose
Right - Alt Alt Graph Right - Option
Left - Alt Alt Left - Option

Instruction Manual
14
Specications
SV431DUSBU SV831DUSBU/
SV831DUSBUK
SV1631DUSBU/
SV1631DUSBUK
Number of Ports 4 8 16
Console Connectors 1 x DE-15 VGA female
2 x USB type A
Computer (PC)
Connectors - Per Port 1 x DE-15 PC Connector female
Rack Mountable Yes (Optional for SV431DUSBU)
Rack Mount Height 1U
Switching Methods Hot-key, Push Button and OSD
LEDs 4 x Power/Active 8 x Power/Active 16 x Power/
Active
Front Push Buttons 4 x Push Button 8 x Push Button 8 x Push Button
Maximum Video
Resolution 1920x1440
On Screen Display
(OSD) Yes
Cascadable Yes
Maximum Number of
Cascaded Computers 16 64 136
Operating
Temperature 5oC to 40oC
Storage Temperature -20oC to 60oC
Humidity 80% RH
Power Adapter 9-12VDC, 500mA(min.)
Dimensions
220.0mm x
130.0mm x
44.0mm
438.0mm x
180.0mm x
44.0mm
438.0mm x
180.0mm x
44.0mm
Weight 1.5kg 2.9kg 3.1kg

Instruction Manual
15
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old
and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
StarTech.com Ltd.
45 Artisans
Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com
LLP
4490 South
Hamilton Road
Groveport, Ohio
43125
U.S.A.
StarTech.com
Ltd.
Siriusdreef 17-27
2132 WT
Hoofddorp
The Netherlands
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com