State Water Heaters Force 90+ SCGSS01108 User manual

COMMERCIAL
FORCE
™
90+
96% Efficient
Power Direct Vent Commercial Gas Water Heater
The 100,000 BTU Force™90+ light-duty commercial gas water heater is equipped with a fully submerged, spiral-shaped condensing heat exchang-
er and 50 gallons of storage capacity. This design provides much greater heat transfer surface than a standard straight flue tube, resulting in
96% thermal efficiency and higher hot water output than comparable 80% efficient water heaters. With a 22˝ diameter, the Force™ 90+ can be
installed in less space than a 75-gallon unit yet delivers greater recovery and lower operating costs.
Power Direct Vent Design for Installation Versatility
• Modular blower, with 120V, 60Hz electrical system (5 amps or less)
• Can be vented vertically thru-the-roof or horizontally thru-the wall.
Vents using PVC, CPVC or ABS pipe.
2˝ pipe allows vent runs up to 45 equivalent feet
3˝ pipe allows vent runs up to 128 equivalent feet
4˝ pipe allows vent runs up to 128 equivalent feet
Available in Natural Gas or Propane
Side-Mounted Taps for Recirculating Systems
• Hot and cold “side taps” allow the Force™ 90+ to be used for “combination” systems
for water heating plus space heating, radiant floor heating or other applications
requiring a recirculating hot water loop
• Plugs for recirculating taps are factory installed
Advanced Electronic Control
• Large LCD display
• Precise temperature control
• Advanced diagnostics
Glasslined Tank with Two Magnesium Anode Rods
• Provides superior protection against corrosion
• Commercial-grade glass lining protects all “water side” tank surfaces plus inside of internal
heat exchanger exposed to condensate
Top-Fired Low-NOx Burner
• Reduces NOx emissions and complies with SCAQMD Rule 1146.2, and other Air Quality Management
Districts with similar requirements for low NOx emissions
CSA Certified and ASME Rated T&P Relief Valve
Maximum Hydrostatic Working Pressure: 150 psi
Meets the thermal efficiency and standby
loss requirements of the U.S. Department
of Energy and current edition of
ASHRAE/IESNA 90.1
Three-Year Limited Tank Warranty
• Consult written warranty shipped with water heater or contact State for complete
warranty information
• Optional concentric vent and sidewall termination kits available
• iCOMM™ Compatible and can be monitored from remote locations.
Call 1.888.WATER02 for more information.
Low Lead Content
SCGSS01108 Revised June 2011
237044_SCGSS01108.indd 1237044_SCGSS01108.indd 1 6/7/11 2:53 PM6/7/11 2:53 PM

For more information on State Water Heaters, contact:
State Water Heaters
500 Tennessee Waltz Parkway
Ashland City, TN 37015
800-365-0024 Toll-free USA
www.statewaterheaters.com SCGSS01108
For complete information on limited warranties, consult written warranty
or contact the State Customer Care Center at 1-800-365-0024.
State Industries, Inc. reserves the right to make product changes or improvements without prior notice.
SUGGESTED SPECIFICATION
(Natural or Propane) gas water heater(s) shall be State Force™ 90+ model # SHE50 100NE, with 96% thermal efficiency, a storage capacity of 50 gallons, an input rating of 100,000 BTU per hour, a recovery
rating of 116 gallons per hour at 100ºF rise and a maximum hydrostatic working pressure of 150 psi. Water heater(s) shall be of power direct vent design, using 2, 3 or 4˝ PVC, CPVC or ABS pipe for horizontal and/or
vertical vent runs. Water heater(s) shall have: 1: Seamless, glasslined steel tank construction and a spiral-shaped heat exchanger placed entirely inside the tank, which shall be glasslined on the flue gas side to
protect against acidic condensate. 2: Advanced electronic control with large LCD display and advanced diagnostics. Water heaters shall incorporae the iCOMM™system for remote monitoring, leak detection and
fault alert. 3: A 3-year limited warranty against tank leaks. Water heater(s) shall meet the thermal efficiency and standby loss requirements of the U.S. Department of Energy and current edition of
ASHRAE/IESNA 90.1.
FORCE
™
90+
96% Efficient
Power Direct Vent Commercial Gas Water Heater
Manifold Pressure: 4.0 inches w.c. (.99 kPa); All models–Maximum Supply Pressure: 14 inches w.c. (3.48 kPa) Minimum Supply Pressure Natural Gas: 3.5 inches w.c.
(.87 kPa). Minimum Pressure Propane: 8.0 inches w.c. (1.99 kPa). Minimum Pressure must be maintained under both load and no-load (static and dynamic)
conditions.
SPECIFICATIONS
DIMENSIONS
SHE50 100NE A B C D E F
INCHES 66-3/4 49-1/4 22 15-3/4 3 8
MODEL
NUMBER
BTU
INPUT
PER
HOUR
TANK
SIZE
GALLONS
RECOVERY–GALLONS
PER HOUR
AT DEGREE RISE
SHIPPING
WEIGHT
LBS.
40ºF 100ºF 140ºF
SHE50 100NE 100,000 50 291 116 83 255
Top inlet and outlet: 3/4˝ male NPT
Side inlet and outlet: 3/4˝ female NPT
Gas inlet: 1/2˝ NPT
Optional Concentric Vent Kit Part # 9003910105
Revised June 2011
*INSTALL IN ACCORDANCE WITH LOCAL CODES.
237044_SCGSS01108.indd 2237044_SCGSS01108.indd 2 6/7/11 2:53 PM6/7/11 2:53 PM