Steamfast MODEL SF-407 User manual

MODEL SF-407
Fabric Steamer
Please read all instructions before use.
Mail in your warranty registration card.
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.
by Top Innovations

Le t t e r f r o m t h e Ceo
Dear Valued Customer,
Congratulations on purchasing your new SF-407 Fabric Steamer. This amazing product
safely and effectively smooths wrinkles and reduces odors, saving you time and money over
traditional irons or dry cleaners.
Plug it in and turn it on, and in just seconds the Fabric Steamer is ready to freshen fabrics and
smooth light wrinkles. Ideal for both quick touch-ups and larger jobs, hot steam rapidly
penetrates deep into the bers of materials, making it perfect for use on garments, draperies,
upholstery and much more.
Additionally, using steam provides a variety of other unique benets. It’s natural and
environmentally friendly, eliminating the need for potentially harmful chemicals. It also helps
to neutralize smoke and other unpleasant odors, rather than simply covering them up with
articial scents.
Top Innovations would like to invite you to visit our Customer Support Web site at:
www.SteamFast.com
On this Web site you will nd helpful tips on ways in which you can utilize your Fabric
Steamer, along with other general guidelines to assist you in maximizing the power of steam.
You will also nd additional information about many other exciting products that are available
for your home, automotive and fabric care needs.
Enjoy your new SF-407 Fabric Steamer!
Benny Lee
Chairman & CEO
Top Innovations
2 Top Innovations

IMPORTANT SAFETY INSTRUCTIONS
Top Innovations 3
WARNING: To reduce risk of re, electrical shock or injury, the following
basic safety precautions should always be followed when using an
electrical appliance.
WARNING: To reduce risk of electrical shock, this appliance has a
grounded (three-prong) plug. This plug will t in a polarized wall outlet
only one way. If the plug does not t fully in the outlet, contact a licensed
electrician to install a proper outlet. DO NOT attempt to modify the plug
or defeat this safety feature.
READ ALL INSTRUCTIONS BEFORE USE
DANGER
Any appliance is electrically live even when switch is off. To reduce risk of electrical shock:
1. Always unplug power cord immediately after using.
2. Do not place or store unit where it can fall or be pulled into a sink or tub.
3. Do not place in, or drop into water or other liquid.
4. If unit falls into water, immediately unplug power cord. Do not reach into the water.
WARNING
To reduce risk of burns, electrocution, re, or injury to persons:
1. Use Fabric Steamer only for its intended purpose as indicated in this manual.
2. When using an extension cord to operate this unit, use a properly rated cord. Use care to position
extension cord where it is least likely to be damaged or tripped over during use.
3. Before plugging power cord into electrical outlet, be sure that all electrical information on rating
label agrees with your power supply.
4. To reduce likelihood of circuit overload, DO NOT operate another high wattage appliance on the
same circuit as this unit.
5. To protect against risk of electrical shock, do not immerse unit in water or other liquids. Do not
use power cord as handle, allow it to hang over edge of counters, or be crimped or closed in doors.
6. Never yank power cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
7. Do not operate unit with a damaged power cord or if the unit has been dropped or damaged. To
avoid risk of electrical shock, do not disassemble unit; contact Top Innovations Customer Support
for examination and repair. Incorrect reassembly can cause a risk of electrical shock when unit is
used.
8. Close supervision is required for any appliance being used near children, pets and plants. Do not
leave unit unattended while plugged in.
9. This unit is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the unit by a person responsible for their safety.

IMPORTANT SAFETY INSTRUCTIONS
4 Top Innovations
10. If Lighted On/Off Switch does not illuminate when power cord is plugged in and Switch is set to
“ON” position, unit is not operating normally. Immediately disconnect cord from power supply,
then refer to troubleshooting guide on Page 14 of this manual for assistance.
11. Always turn off unit and unplug power cord when not in use.
12. Do not use unit outdoors or operate where aerosol (spray) products are being used, or where
oxygen is being administered.
13. Unit is only meant to be used with recommended SF-407 accessories. Using other types of
attachments may cause damage to unit or injury.
14. When lling Water Tank, only distilled or de-mineralized water should be used in unit, in order
to minimize potential build-up of mineral deposits. Other cleaning agents could damage unit or
cause injury. Do not overll unit.
15. Do not attempt to use steam without properly lling Water Tank.
16. To reduce risk of contact with hot water emitting from steam vents, check appliance before each
use by holding Steam Nozzle away from body. Do not operate unit if steam vents are blocked.
17. Burns can occur from touching hot metal parts, hot water, or steam. Do not turn unit upside-
down – it may contain hot water.
18. When pressing/steaming any item for the rst time, it is recommended that you consult the
manufacturer’s guidelines for material being steamed. For items in question, test on an
inconspicuous area before proceeding.
19. Do not allow power cord to touch hot surfaces during use. Wrap cord loosely around unit when
storing.
20. Always allow Fabric Steamer to cool completely (at least 30 minutes) before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY

Pr o d u C t In f o r m a t I o n
Top Innovations 5
The following features and accessories are included with your Fabric Steamer. Carefully inspect the
packing material for all parts listed below. To obtain possible missing parts, refer to the Customer
Support section on Page 14 of this manual.
UN I T FE A T U R E S
& AC C E S S O R I E S
Pole Top
Clothes Hanger Hook
Steam Nozzle Holder
Steam Nozzle
Handle
Telescopic Pole
Pole Base
Hose
Hose Base
Water Tank
Valve Cap
Water Reservoir
Lighted On/Off Switch
Drain Plug
Rolling Casters
Fabric Brush
Press Pad
1.
1A.
1b.
2.
3.
4.
4A.
5.
5A.
6.
6A.
7.
8.
9.
10.
11.
12.

Pr o d u C t In f o r m a t I o n
6 Top Innovations
•The Pole Top (1) connects to the top section of the Telescopic Pole.
•The Clothes Hanger Hook (1A), which is part of the Pole Top, is designed to support garments
hung from a clean rust-free hanger.
•The Steam Nozzle Holder (1B), which is part of the Pole Top, provides a safe and convenient place
to hang the Steam Nozzle when not in use.
•The Steam Nozzle (2) emits the ow of hot, penetrating steam.
•The Handle (3) is designed to stay relatively cool while providing an optimum level of safety and
user comfort.
•The Telescopic Pole (4) connects to the unit at the Pole Base. The Telescopic Pole is divided into
four sections, three of which can be extended and retracted for user comfort and convenient
storage. The Pole Top connects to the Telescopic Pole.
•The Pole Base (4A) is the threaded receptor into which the Telescopic Pole is inserted.
•The Hose (5) directs steam from the unit’s internal boiler to the Steam Nozzle, while remaining safe
and exible for a wide variety of uses.
•The Hose Base (5A) is the threaded receptor onto which the Hose is connected.
•The Water Tank (6) holds water to be transferred into the Water Reservoir, up to a maximum
capacity of 40 oz. (1,183 ml.). The Water Tank is removable for convenient lling.
•The Valve Cap (6A) controls the ow of water between the Water Tank and the Water Reservoir.
The Valve Cap must be removed in order to empty or ll the Water Tank.
•The Water Reservoir (7) is where water is stored before being converted into steam by the internal
boiler. Water from the Water Tank is transferred as needed into the Water Reservoir through the
Valve Cap.
•The Lighted On/Off Switch (8) turns the unit on and off. When set to the “ON” position, it
illuminates to provide a clear visual indication that the unit is receiving power.
•The Drain Plug (9) may be opened to easily empty any remaining water out of the Water Reservoir.
•The Rolling Casters (10) allow for exceptional mobility and freedom of movement over a variety
of surfaces.
•The Fabric Brush (11) connects to the Steam Nozzle and is designed to work with steam to remove
lint, loose threads and exceptionally stubborn wrinkles.
•The Press Pad (12) is designed with a strap that ts over your hand, allowing you to easily support
fabrics for steaming edges and creating crisp creases. The Press Pad also protects your hand from
being burned by hot steam.

as s e m b L I n g y o u r
Fa b r i c St e a m e r
Top Innovations 7
TELESCOPIC POLE
The Telescopic Pole is made up of four sections (FIGURE 1):
•TOP (SECTION 1)
•MIDDLE-TOP (SECTION 2)
•MIDDLE-BOTTOM (SECTION 3)
•BOTTOM (SECTION 4)
SECTIONS 1, 2 & 3 are adjustable in length. By using the three extension locks, these sections
may be extended or retracted in order to achieve the desired length. Refer to Adjusting Telescopic
Pole section below for more details.
NOTE: SECTION 4 (BOTTOM) is the widest section of the Telescopic Pole. This section
includes the COUPLING, which secures the Telescopic Pole to the Pole Base.
ADJUSTING TELESCOPIC POLE
In order to adjust the length of SECTIONS 1, 2 & 3 of the
Telescopic Pole:
1. Release extension lock directly below SECTION 1 by
swinging hinge outward as shown. SECTION 1 above
it can then be extended / retracted (FIGURE 2).
2. Once SECTION 1 is at desired length, close hinge to
once again secure extension lock.
3. Repeat STEPS 1 & 2 for SECTIONS 2 & 3 of the
Telescopic Pole, using the extension lock directly below
each of those sections.
NOTE: It is recommended to extend Telescopic Pole to
its full height during steamer operation in order to
insure a free ow of steam through the Hose. FIGURE 2
FIGURE 1

as s e m b L I n g y o u r
Fa b r i c St e a m e r
8 Top Innovations
CONNECTING TELESCOPIC POLE
1. Locate COUPLING on SECTION 4 of Telescopic
Pole. The Telescopic Pole is packed with COUPLING
already on SECTION 4 – if the COUPLING has fallen
off, simply slide it back on as shown in FIGURE 1.
2. Look down inside Pole Base, and locate two guide
ridges (FIGURE 3-A). Align two guide grooves on
Telescopic Pole (FIGURE 3-B) with guide ridges
inside Pole Base.
3. With guide grooves aligned with guide ridges, insert
SECTION 4 of Telescopic Pole into Pole Base
(FIGURE 3-C).
NOTE: If you have trouble locating two guide
ridges inside Pole Base, insert SECTION 4 of
Telescopic Pole into Pole Base, then twist Pole to
properly align the guide grooves and guide ridges.
4. Slide COUPLING down over Pole Base, then screw
clockwise to secure Telescopic Pole in place
(FIGURE 3-D). The Telescopic Pole should now be
secured to the Pole Base.
CONNECTING POLE TOP
1. Look at underside of Pole Top, and locate two guide ridges
(FIGURE 4-A).
2. Align Pole Top guide ridges with guide grooves on SECTION 1
of Telescopic Pole. Be sure to orient Pole Top so that Nozzle
Holder faces toward front of unit. This will help to improve
unit stability when heavy garments are hung from the
Clothes Hanger Hook.
3. Slide Pole Top onto SECTION 1 of Telescopic Pole
(FIGURE 4-B). Press down rmly until Pole Top ts
securely in place.
FIGURE 3
FIGURE 4
C
D
A
B
A
B

as s e m b L I n g y o u r
Fa b r i c St e a m e r
Top Innovations 9
CONNECTING FABRIC BRUSH
1. Make sure Lighted On/Off Switch is set to “OFF” position, and that
unit is not emitting any steam.
CAUTION: Do not try to connect Fabric Brush while unit is
emitting steam, as this can cause burns and injury.
2. Align the four pegs on back of Fabric Brush (2 circular and 2
elliptical) with corresponding holes on face of Steam Nozzle.
3. Press Fabric Brush rmly onto Steam Nozzle, until it ts snugly
and rmly in place (FIGURE 5).
CONNECTING HOSE
1. Place end of Hose onto threaded Hose Base (FIGURE 6-A).
2. Rotate coupling in clockwise direction until Hose is tightly secured onto Hose Base
(FIGURE 6-B). Hand tighten only. Do not over-tighten.
3. Hang Steam Nozzle on specially designed Steam Nozzle Holder (FIGURE 6-C).
CAUTION: To prevent steam from causing bodily injury or damage to surfaces, always hang
Steam Nozzle on Steam Nozzle Holder when not in use. Do not lay the Steam Hose on the oor
as condensation may occur, causing unwanted water droplets in the steam. Do not pull on the
Steam Hose with excessive force as this may damage it, resulting in a steam leak.
Your new SF-407 Fabric Steamer is now fully assembled and ready for use. Please continue
reading this manual for instructions on using the Fabric Steamer, as well as directions for proper
cleaning, storage and troubleshooting.
FIGURE 5
FIGURE 6
A B
C

us I n g y o u r
Fa b r i c St e a m e r
10 Top Innovations
FILLING WITH WATER
1. Remove Water Tank from main unit.
2. Holding Water Tank upside-down, unscrew and remove Valve Cap by rotating it in a counter-
clockwise direction (FIGURE 7-A).
3. Fill Water Tank with water through Valve Cap hole. Refer to guidelines on left side of Water Tank
to ll it with correct amount of water, depending on desired steam time (15, 30, or 45 minutes).
Do not exceed 45 MIN (40 oz. / 1,183 ml.) mark.
NOTE: To prolong the life of your Fabric Steamer, it is recommended that distilled or
de-mineralized water be used in Water Tank.
CAUTION: Only water should be used in unit – other chemicals or cleaning agents may
cause internal damage. Do not attempt to substitute another water tank for the one designed
for use with this unit.
4. Replace Valve Cap by rotating it in a clockwise direction.
5. Place Water Tank back onto main unit (FIGURE 7-B). The sound of water owing from Water
Tank into Water Reservoir should be audible for a short period of time.
IMPORTANT: Do not attempt to operate unit with an empty Water Tank.
FIGURE 7
A
B

us I n g y o u r
Fa b r i c St e a m e r
Top Innovations 11
OPERATING YOUR FABRIC STEAMER
NOTE: Be sure that Water Tank has been lled and, if desired, the Fabric Brush is connected
before following these steps.
1. For rst-time use, remove protective plastic cover that is shipped on electrical plug. Plug power
cord into a convenient 3-prong electrical outlet (FIGURE 8-A).
CAUTION: This unit uses a grounded (3-prong) electrical plug. Use only in properly
installed 3-prong electrical outlets. Do not attempt to alter plug or circumvent this safety
feature in any way.
2. Set Lighted On/Off Switch to “ON” position (FIGURE 8-B), and verify that switch is illuminated.
3. After approximately 40 seconds of heating time, unit will begin producing a ow of steam from
Steam Nozzle.
NOTE: It is common for the unit to produce gurgling sounds and small amounts of water
during the rst few minutes of steaming. This is a natural part of the steaming process.
Pointing Steam Nozzle towards the ground and shaking it may help to remove excess water
from Hose more quickly (FIGURE 8-C).
4. Once steam ow is steady and excess condensation has been removed from Hose, you may
proceed with your steaming tasks. Refer to Tips for Using Your Fabric Steamer section on Page
12 for more information about steaming garments and other fabrics.
CAUTION: Always be sure that Steam Nozzle is pointed in a safe direction (away from
yourself, other people, pets and plants) when steaming.
5. When you are nished using the Fabric Steamer, immediately set Lighted On/Off switch to “OFF”
position and unplug power cord from electrical outlet. Refer to Care and Storage Guidelines on
Page 13 for proper cleaning and storage procedures.
FIGURE 8
A B C

us I n g y o u r
Fa b r i c St e a m e r
12 Top Innovations
TIPS FOR USING YOUR FABRIC STEAMER
STEAMING GARMENTS
1. Place garment on a clean, rust-free clothes hanger.
2. Place hanger (with garment) on Clothes Hanger Hook
(FIGURE 9-A).
CAUTION: Use care when handling garments on
the Clothes Hanger Hook. Pulling on the garment
with too much force may cause the unit to tip over.
3. Direct Steam Nozzle towards bottom of garment.
Steam will rise along inside and outside of fabric,
removing wrinkles. Slowly slide Steam Nozzle
vertically, from bottom to top of garment
(FIGURE 9-B).
NOTE: Do not allow kinks to form in hose at any
time during use.
4. Direct Steam Nozzle away from garment and smooth
fabric with your free hand.
5. Repeat STEPS 3 & 4 as necessary until fabric is
smooth and wrinkle-free.
GENERAL STEAMING TIPS
•For best steaming results, press Steam Nozzle directly
against fabric, or hold within 1/2” of surface.
•Curtains and draperies may be steamed while still
hanging.
•To remove wrinkles from towels, handkerchiefs and
napkins, drape them over a rod or towel rack and
gently steam them.
•Heavier fabrics may require repeated steaming to
effectively remove wrinkles.
•To remove exceptionally stubborn wrinkles steam both
sides of fabric.
•For additional assistance in removing tough wrinkles,
or to remove lint and other particles, connect Fabric
Brush to Steam Nozzle (refer to Connecting Fabric
Brush section on Page 9).
• The Press Pad is ideal for steaming difcult spots and
edges and to create creases in fabric. Slide your hand
through the velcro strap on back of Press Pad to secure
it to your hand. This will protect your hand from the
ow of hot steam. Then steam fabric while pressing it
rmly but gently against the Press Pad.
FIGURE 9
A
B

Top Innovations 13
Ca r e & st o r a g e gu I d e L I n e s
PROPER STORAGE
Preparing your Fabric Steamer for storage is quick and simple. When you have nished your
steaming tasks, follow the steps listed below.
1. Set Lighted On/Off Switch to “OFF” position, and unplug power cord from electrical outlet.
2. Allow unit to cool completely (at least 30 minutes is recommended).
3. Remove Water Tank from unit. Unscrew Valve Cap and drain remaining water into sink or tub.
Replace Valve Cap when nished.
NOTE: It is not necessary to empty Water Tank after each use if you do not wish. However,
it is recommended that it be drained for storage and lled with fresh distilled water for each
use.
4. Remove Drain Plug and drain any remaining water in Water Reservoir into a sink or tub to prevent
overlling during your next use. Flush out Water Reservoir with fresh water to minimize potential
mineral build-up in Water Reservoir. Replace empty Water Tank.
5. For storage convenience, you may wish to collapse Telescopic Pole to its most compact height
(refer to Page 7 for details).
6. Wrap power cord loosely around unit, and store Fabric Steamer in a cool dry location.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the effectiveness
and reduce the life of your Fabric Steamer.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your Fabric Steamer.In addition, it is recommended that the unit be cleaned regularly using
the procedure below. This will help to extend the life of your Fabric Steamer, and keep it
functioning at its maximum potential.
NOTE: It is recommended that the following procedure be followed once every 3-4 uses.
1. Set Lighted On/Off Switch to “OFF” position, and unplug power cord from electrical outlet.
2. Allow unit to cool completely (at least 30 minutes is recommended).
3. Remove Water Tank from unit. Unscrew Valve Cap and drain remaining water into sink or tub.
4. Remove Drain Plug and drain any remaining water in Water Reservoir into a sink or tub.
5. Using measuring cup (not included), make a mixture of 6 oz. (177 ml.) vinegar and 6 oz. (177 ml.)
distilled water.
6. Slowly pour water-vinegar solution into Water Tank, then replace Valve Cap and place Water Tank
back onto unit.
7. Set Lighted On/Off Switch to “ON” position. Allow unit to heat up and steam out all of the
water-vinegar solution.
8. Once emptied, set Lighted On/Off Switch back to “OFF” position. Remove Water Tank and rell
with approximately 12 oz. (355 ml.) fresh distilled water, then replace Water Tank.
9. Set Lighted On/Off Switch to “ON” position. Allow unit to heat up and steam out all of the fresh
distilled water. Once emptied, set Lighted On/Off Switch back to “OFF” position.
10. Repeat STEPS 8 & 9 as necessary until vinegar odor completely dissipates. Once nished,
follow normal storage guidelines outlined above.

tr o u b L e s h o o t I n g / Cu s t o m e r su P P o r t
14 Top Innovations
CUSTOMER SUPPORT
For problems with your Fabric Steamer, please refer to the troubleshooting guide located above.
Additional inquiries should be directed to our customer support services through our Web site,
www.SteamFast.com, on the Contact Us Web page.
If you do not have internet access, you may also contact our Customer Service Department by
telephone, at [phone] or [phone], ext. 130 or 131.
NOTE: In order for our Customer Service representatives to help you as quickly and
efciently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number
PROBLEM
Unit fails to steam. Lighted
On/Off Switch DOES NOT
illuminate when set to “ON”
position.
Unit fails to steam. Lighted
On/Off Switch DOES illuminate
when set to “ON” position.
Steam output is weak or
intermittent.
Excessive gurgling in Hose and
Steam Nozzle / water drips from
Steam Nozzle.
POSSIBLE CAUSE
Unit is not plugged in.
No water in unit.
Mineral build-up in unit.
Mineral build-up in unit.
Condensation build-up inside Hose.
Household circuit breaker / ground
fault interrupter has tripped or
blown a fuse.
Unit is damaged or otherwise in
need of repair.
Unit is damaged or otherwise in
need of repair.
SOLUTION
Plug power cord into electrical
outlet.
Refer to Filling With Water
procedure on Page 10.
Refer to Mineral Build-Up
procedure on Page 13.
Refer to Mineral Build-Up
procedure on Page 13.
Some gurgling is a natural effect
of the steaming process. For
excessive gurgling or dripping
water, point Steam Nozzle towards
ground shake thoroughly to
remove excess water droplets.
Reset circuit breaker / ground fault
interrupter, or replace fuse. If you
need assistance, contact a licensed
electrician.
Immediately cease usage and
unplug. Contact Customer Support
for further assistance (see below).
Immediately cease usage and
unplug. Contact Customer Support
for further assistance (see below).

Wa r r a n t y In f o r m a t I o n
30-DAY MONEY BACK POLICY
If any item purchased directly from Top Innovations does not meet your expectations, it may be returned within 30
days of the date of purchase for either a replacement or full refund of the purchase price less any shipping charges.
In some circumstances, an additional restocking fee will apply.
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations warrants this product to be free from defects in material and workmanship for a period of one
(1) year from the date of purchase. This warranty does not cover damage caused by misuse, negligence, use by
improper current or voltage, commercial use, use contrary to operating instructions or disassembly, repair or
alteration by any person other than Top Innovations Warranty Service Department.
Top Innovations will repair or replace at its option. This warranty gives you specic legal rights and may have
other rights, which may vary from state to state.
Should there be any missing or defective parts or accessories, please contact Customer Support. In most cases, it is
not necessary to return the entire unit. We can ship most replacement parts directly to your home.
Upon expiration of your one (1) year limited warranty, you will be advised of the cost of repair before any servicing
is done. For non-warranty service, please enclose a check for the amount required. Or, you may pay by money
order, Visa, MasterCard, AmEx or Discover credit card. You must have a Return Authorization Number before
returning unit.
If you need to request warranty service, or have any questions about coverage under this warranty, please visit the
Warranty Service Request page on our Web site, www.SteamFast.com. You may also e-mail
[email protected], or phone [phone] or [phone], ext 130 or 131.
Please have your product serial number ready before contacting Warranty Service Department. The serial number
is located on the back or bottom of your unit.
Performance of any obligation of this Warranty, or 30-Day Money Back Policy, may be obtained by:
1. Call [phone] or e-mail [email protected] for a Return Authorization Number before
returning your unit. Failure to obtain a Return Authorization Number will cause a delay in service.
2. Include a copy of purchase receipt.
3. Box the item securely, in its original packaging if available. Include original packing materials and accessories
unless advised otherwise by a Customer Service agent.
4. Include your name, address, telephone number, and Return Authorization Number on outside of return package.
Send unit postage/freight-prepaid (Top Innovations does not accept “collect” or COD returns) to:
Top Innovations
Warranty Service Department
6655 Troost Ave.
Kansas City, MO 64131
Call Top Innovations, Customer Service at [phone] or [phone] if you have any questions about the
procedures described above.
Before returning any product for any reason, you MUST call or e-mail Top Innovations
Warranty Service at [phone] or [email protected] to obtain a
Return Authorization Number.
Top Innovations 15

Top Innovations
6655 Troost Ave. • Kansas City, MO 64131
TEL: [phone]
FAX: [phone]
www.SteamFast.com
[email protected]
V081205
PRINTED IN CHINA
PRODUCT SERIAL NUMBER
For your convenience, space has been provided below for you to record the serial number of
your unit (located on the back or bottom of the unit) for easy reference when contacting our
Customer Service Department.
____________________–________________________________________________________