Steamfast Quick & Easy SF-222 User manual

Quick & Easy
TM
Steam Cleane
r
Model SF-222
by Top Innovations, Inc.
Please read instructions before use.
Mail in your warranty registration card.

Dear Valued Customer,
Thank you for purchasing the Quick & Easy
TM
handheld steam cleaner.
This versatile and convenient new product places the cleaning power of
steam in a compact and lightweight appliance that is easy to take anywhere
you need to clean.
Plug your Quick & Easy
TM
in, and in minutes, you are ready to eliminate
dirt, grease, grime, stains, and more from most anywhere in or around your
home. In addition to removing dirt and grime, you will receive the many
benefits that steam provides. Hot steam refreshes upholstery and eliminates
smoke and other unpleasant odors, as well as dust mites and other allergens.
Use it in your living room, kitchen, bedrooms, bathrooms, and anywhere
else that you need to clean. And when you’re finished steaming, the Quick
& Easy
TM
light weight and compact size make it quick and convenient to
store.
Top Innovations, Inc. would like to invite you to take advantage of our
Customer Support web site at:
www.topinnovations.com
On this website you will find additional information about many other
exciting Steam Fast products that are available, helpful tips on ways in
which you can utilize your Quick & Easy
TM
, and other useful information
to assist you in maximizing the power of steam!
Enjoy your new Quick & Easy
TM
!
Benny Lee
Chairman and CEO
Top Innovations, Inc.
L ETTER FROM THE CEO
2
To
p
Innovations
,
Inc.

CUSTOMER SUPPORT
For problems with your steam cleaner, refer to the Troubleshooting
Guide Located on page 13 of this manual. Additional inquiries should be
directed to our Customer Support services at 1-800-711-6617 ext. 102 /
130 or e-mailed to:
[email protected]
Should there be any missing or defective parts or accessories, contact
Customer Support. In most cases, it is not necessary to return the entire
unit. We can ship most parts directly to your door.
To ensure prompt and accurate service, call for a Return
Authorization number before returnin
g
an
y
unit to Top Innovations.
Failure to obtain a Return Authorization number will cause a delay
in warranty or out-of-warranty service requests.
C USTOMER S UPPORT
3
To
p
Innovations
,
Inc.

1. DO NOT leave your SF-222 Quick & Easy
TM
unattended when plugged in
or not in use.
2. This unit is not a toy. Close supervision is required when using
unit near children, pets, and plants. Steam produced by it is hot and
pressurized. Care must be taken to avoid burns or other injuries. Never
point nozzle at pets or people.
3. Always unplug electrical cord when unit is not in use. DO NOT use this
unit if electrical cord or outlet is damaged. DO NOT use unit if it is not
working properly or has been dropped, damaged, or left outdoors. If such
damage occurs, return unit to an approved service technician for repair.
4. This unit is an electrical appliance. DO NOT submerge it in water. DO
N
OT use electrical cord as a handle. DO NOT allow cord to be crimped by
closing it in doors. DO NOT pull or stretch cord around sharp corners or
edges. Be sure to keep electrical cord away from all heated surfaces.
5. DO NOT use this unit with extension cords or electrical outlets that have
inadequate current capacity. A three-prong outlet or a properly grounded
adapter is necessary when using SF-222 Quick & Easy
TM
.
6. In order to unplug SF-222 Quick & Easy
TM
, grasp plug and pull smoothly
and firmly from outlet. DO NOT attempt to unplug unit by pulling or
tugging on cord.
7. DO NOT handle or use this unit while hands are wet or when not wearing
shoes. To avoid falls and other injuries, be sure to dry any wet areas on
floors and to stand away from damp surfaces while using steam cleaner.
SAVE THESE INSTRUCTIONS!
F OR HOUSEHOLD USE ONLY
4
I MPORTANT S AFEGUARDS
WARNING: To reduce the risk of fire, electrical shock, or
injury, the following basic safety precautions should always
be followed when using an electrical appliance.
READ ALL INSTRUCTIONS BEFORE USING YOUR STEAM CLEANER
To
p
Innovations
,
Inc.

8. SF-222 Quick & Easy
TM
is only meant to be used with recommended
SF-222 accessories. Other types of attachments such as those used with
vacuum cleaners are not to be used with Quick & Easy. Doing so may cause
injuries or damage to unit.
9. Nozzles and attachments become hot during use. To avoid injuries, DO
N
OT touch nozzles while using this appliance. DO NOT attempt to change
attachments while unit is emitting steam.
10. DO NOT turn unit on its side when in use.
11. When filling your Quick & Easy
TM
with water, DO NOT overfill Water
Reservoir.
12. Before filling unit with water, always take the following steps:
(1) Turn appliance off
(2) Unplug electrical cord
Failure to follow these steps may result in electric shock and injury.
13. Only water should be used in unit. Other cleaning agents will damage
unit and can cause injuries.
14. DO NOT operate unit if steam opening is blocked. Should this occur,
shut unit off and unplug.
15. Store your SF-222 Quick & Easy
TM
in a cool, dry place. Allow unit to
cool completely, and always drain Water Reservoir before storing.
SAVE THESE INSTRUCTIONS!
F OR HOUSEHOLD USE ONLY
5
I MPORTANT S AFEGUARDS
WARNING: To reduce the risk of electric shock, this appliance
has a three-pronged plug. This plug will fit in a polarized wall
outlet only one way. If the plug does not fit fully in the outlet,
contact a qualified electrician to install a proper outlet. DO NOT
attempt to modify the plug or defeat this safety feature in any way.
To
p
Innovations
,
Inc.

SF-222 Q UICK & E ASY
TM
P RODUCT
I NFORMATION
The following features and accessories come with your steam cleaner.
Carefully inspect packaging material as some parts are shipped inside
Styrofoam packaging. To obtain possible missing parts, refer to the
Customer Support section on page 3 of this manual.
6
To
p
Innovations
,
Inc.
UNIT ACCESSORIES
7. Steam Jet Nozzle
8. Measuring Cup
9. 10 mm Nylon Utility Brush
10. 15 mm Nylon Utility Brush
UNIT FEATURES
1. Water Reservoir Cap
2. Steam Button
3. Handle
4. Grounded Power Cord
5. Steam Ready Light
6. Water Reservoir

·The Water Reservoir Cap (1) securely covers the opening to the Water
Reservoir, safely containing the pressurized steam within the boiler. The
Water Reservoir Cap must be removed in order to fill the unit with water.
·The Steam Button (2) is depressed in order to release a spray of hot,
penetrating steam from the unit.
·The Handle (3) is designed to stay relatively cool and safe while
providing the optimum amount of user comfort.
·The Grounded Power Cord (4) provides a maximum amount of safety
against electrical shock, while still allowing a great deal of freedom and
mobility.
·The Steam Ready Light (5) illuminates to indicate that the boiler is
heating, and deactivates when the unit is ready to begin steaming.
·The Water Reservoir (6) is the tank in which water is stored for use by
the unit. There must be a sufficient amount of water in the Water
Reservoir in order for the unit to function.
·The Steam Jet Nozzle (7) is the only accessory that is required at all times
in order for the unit to function. It focuses the spray of steam, and serves
as the base to which all other attachments connect.
·The Measuring Cup (8) is designed to assist you in consistently filling
the unit with the optimum amount of water.
·The 10 mm Nylon Utility Brush (9) and the 15 mm Nylon Utility Brush
(10) attach to the Steam Jet Nozzle, and provide extra power for
removing exceptionally tough dirt and stains from surfaces.
SF-222 Q UICK & E ASY
TM
P RODUCT
I NFORMATION
7
To
p
Innovations
,
Inc.

ATTACHING STEAM JET NOZZLE
1. Insert cylinder on back of Steam Jet Nozzle (FIGURE 1) into hole on face
of main unit (FIGURE 2). Insert it so that two tabs on sides of cylinder
(FIGURE 1-A) fit into two tab holes on sides of main hole (FIGURE 2-B).
Be sure to push Steam Jet Nozzle in as far as possible.
A SSEMBLY I NSTRUCTIONS
8
2. Rotate Steam Jet Nozzle in a clockwise direction as indicated below
(FIGURE 3). Twist until you feel it “lock” into place and it will move no
further. Note that single guide line on top of main unit aligns between
dual guide lines on Steam Jet Nozzle (FIGURE 4).
To
p
Innovations
,
Inc.
WARNING: Do not attempt to connect any attachments while unit is
emitting steam.
FIGURE 3 FIGURE 4
FIGURE 1 FIGURE 2

9
A SSEMBLY I NSTRUCTIONS
ATTACHING UTILITY BRUSHES
1. Both the 10 mm Nylon Utility Brush and 15 mm Nylon Utility Brush are
attached in the same manner. Begin by aligning hexagonal-shaped hole
on back of desired brush with the hexagonal tip of the Steam Jet Nozzle
(FIGURE 5).
To
p
Innovations
,
Inc.
FIGURE 5
2. Firmly press Nylon Utility Brush onto tip of Steam Jet Nozzle
(FIGURE 6).
IMPORTANT: Make sure brush is pushed as far as possible onto tip to
ensure that it is properly set in place and space between Nylon Utility
Brush and Steam Jet Nozzle is sealed (FIGURE 7). This prevents
heated steam from escaping and causing injury.
FIGURE 6
FIGURE 7
3. To remove Nylon Utility Brush, make sure unit is unplugged and has
had sufficient time to cool down. Then simply grasp brush and firmly
pull until it disconnects from Steam Jet Nozzle.

U SING THE Q UICK & E ASY
TM
FILLING QUICK & EASY
TM
WITH WATER
1. Place Quick & Easy
TM
on a flat, level surface.
2. Make sure power cord is unplugged from electrical outlet.
3. Press and hold Steam Button to ensure that any remaining steam has been
emitted from unit.
4. While still depressing Steam Button, cautiously unscrew and remove
Water Reservoir Cap.
CAUTION: Always press Steam Button while unscrewing Water Reservoir Cap.
This ensures that any steam inside unit will be safely vented out of nozzle.
5. Allow unit to cool for at least 3 minutes.
WARNING: Always allow unit to cool before adding water. Cold water added to
a hot boiler may cause hot water and steam to shoot out of fill hole.
6. Remove Water Reservoir Cap and empty any water remaining in Water
Reservoir from previous use.
CAUTION: Emptying unit before filling ensures that proper amount of water is
added. Too much water may cause excess water in steam and could damage unit.
7. Fill Measuring Cup to maximum fill line with water (6 oz.)
NOTE: To prolong lifetime of Quick & Easy
TM
, we recommend using distilled or
de-mineralized water.
8. Carefully pour water from Measuring Cup into Water Reservoir through
fill hole.
WARNING: Extreme caution should be used when pouring water into boiler. Do
not look directly down fill hole when filling. Keep your free hand and any children
or pets at a safe distance.
9. Replace Water Reservoir Cap, using caution not to over tighten it.
10
To
p
Innovations
,
Inc.

U SING THE Q UICK & E ASY
TM
OPERATING QUICK & EASY
TM
NOTE: Be sure that Water Reservoir has already been filled and desired
attachments are connected before following these steps.
1. Plug power cord into a convenient electrical outlet. Steam Ready Light
will immediately illuminate. (Note: Steam Ready Light is illuminated
while boiler is heating. This unit has no On/Off power switch.)
CAUTION: This unit uses a grounded (3-prong) electrical plug. Use only in
properly installed 3-prong electrical outlets. Do not attempt to alter plug or
circumvent this safety feature in any way.
2. Steam Ready Light will deactivate in 3-4 minutes, indicating that
boiler is heated and Quick & Easy
TM
is ready to begin steaming.
3. Direct Steam Jet Nozzle (and any attachments) towards surface you
desire to steam, and press Steam Button.
CAUTION: Always be sure that Steam Jet Nozzle and any other attachments
are pointed in a safe direction (away from yourself, other people, pets, and
plants) before pressing Steam Button.
4. Keep Steam Button depressed for a constant stream of steam. Using a
slight back-and-forth motion over the area you are steaming will further
enhance the cleaning process.
NOTE: During use Steam Ready Light may illuminate. This is normal. If you
notice a drop in steam pressure, release Steam Button until Steam Ready Light
deactivates once again.
5. Once steaming task is complete, immediately unplug power cord from
electrical outlet. Follow steps under Proper Storage procedure on page
12 of this manual.
11
To
p
Innovations
,
Inc.

PROPER STORAGE
Preparing your Quick & Easy
TM
for storage is quick and simple. When you have
finished your steaming tasks, follow the steps listed below:
1. Unplug power cord from electrical outlet.
2. Allow unit to cool completely (at least 30 minutes).
3. Remove all attachments from unit.
4. Drain any remaining water in Water Reservoir into a sink or tub to prevent
overfilling during your next use. Flush out Water Reservoir with fresh water to
minimize potential mineral buildup in Water Reservoir.
5. Store all attachments safely away, preferably near Quick & Easy
TM
.
6. Store Quick & Easy
TM
in a cool, dry location.
C ARE AND S TORAGE G UIDELINES
REMOVING MINERAL BUILD-UP
One common problem with steam appliances is mineral build-up caused by high
mineral content in many municipal water supplies.
The best way to avoid this is to use de-mineralized or distilled water in unit.
If you are unable to use de-mineralized or distilled water, we recommend you use
this procedure monthly to help avoid mineral build-up:
1. Unplug power cord from electrical outlet and allow unit to completely cool.
2. Remove all attachments from unit.
3. Remove Water Reservoir Cap and drain Water Reservoir into sink or tub.
4. Using Measuring Cup, make a mixture of 3 oz. vinegar and 3 oz. water.
5. Slowly pour water-vinegar solution into Water Reservoir.
6. Allow to stand for 40 minutes.
7. Drain water-vinegar solution from Water Reservoir.
8. Rinse Water Reservoir with fresh water and drain until vinegar odor dissipates.
9. Replace Water Reservoir Cap.
12
To
p
Innovations
,
Inc.

T ROUBLESHOOTING G UIDE
PROBLEM POSSIBLE CAUSE SOLUTION
Unit fails to heat up. Steamer is not plugged
in.
Plug into electrical
outlet.
Household Circuit
Breaker / Ground Fault
Interrupter has tripped or
blown a fuse.
Reset Circuit Breaker /
Ground Fault Interrupter,
or replace fuse. If you
need assistance, contact a
qualified electrician.
Unit heats up, but fails to
steam.
Mineral buildup in unit.
Water Reservoir is
empty.
Follow Removing
Mineral Buildup
procedure on page 12 of
this manual.
Refill Water Reservoir
using procedures on page
10 of this manual.
Steam output is
intermittent.
Mineral buildup in unit. It is normal for unit to
periodically stop
steaming for a few
seconds. If steam stays
off for longer periods,
follow Removing
Mineral Buildup
procedure on page 12 of
this manual.
13
To
p
Innovations
,
Inc.

14
PART PART DESCRIPTION PRICE
(FOR 1)
QTY. TOTAL
Method of Payment (no C.O.D. orders)
Check or Money Order (payable to Top Innovations)
Charge to my VISA MASTERCARD
ACCOUNT NUMBER
EXPIRATION DATE
SIGNATURE: ____________________________________________
N
AME: __________________________________________________
MAILING ADDRESS: _____________________________________
_
________________________________________________________
TELEPHONE: ____________________________________________
(Full name as shown on account)
M ODEL SF-222
A222-001 SF-222 Steam Jet Nozzle $3.99
A222-002 SF-222 Measuring Cup $1.99
A222-003 SF-222 10mm Nylon Utility Brush $2.99
A222-004 SF-222 15mm Nylon Utility Brush $2.99
ACCESSORY ORDER FORM
Q
UICK & E ASY
TM
S TEAM C LEANE
R
To
p
Innovations
,
Inc.
$3.99
$11.96
$3.96
$7.96
$7.96
Subtotal
+ Shipping & Handling
Total USD
PRICE
(FOR 4)
TO ORDER:
O
NLINE
Visit our website at
www.topinnovations.com
B Y M AIL
Fill out this form and
return to address on back
of this manual
B Y P HONE
[phone]
EXT. # 102/130
B Y F AX
[phone]
ORDER ONLINE TODAY
To try our convenient and totally secure
online ordering service, visit us at
www.to
p
innovations.com.

W ARRANTY I NFORMATION
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations, Inc. warrants this product to be free from defects in material
and workmanship for a period of one (1) year from the date of purchase. This
warranty does not cover damage caused by misuse, negligence, use by
improper current or voltage, use contrary to operating instructions or
disassembly, repair or alteration by any person other than Top Innovations,
Inc. Warranty Service Department.
Top Innovations, Inc. will repair or replace, at its option. This warranty gives
you specific legal rights and may have other rights, which may vary from
state to state.
Performance of any obligation under this warranty may be obtained by:
1. Call [phone] for Return Authorization Number before returning
for repair
2. Include copy of purchase receipt
3. Include your name, address, telephone number, and Return Authorization
Number on returned package
Please send product postage prepaid to:
TOP INNOVATIONS, INC.
WARRANTY SERVICE DEPARTMENT
400 NW PLATTE VALLEY DR.
RIVERSIDE, MO 64150
After 1 year limited warranty has expired, you will be advised of the cost of
repair before any servicing is done unless you enclose a note indicating that
you would like us to proceed with repairs.
If you have any questions about coverage under this warranty, you may
contact warranty service department by telephone at [phone] ext. 102
/
130 or e-mail custom[email protected]
15
To
p
Innovations
,
Inc.

Printed In China
Top Innovations, Inc.
400 NW Platte Valley Dr.
Riverside, MO 64150
Tel: [phone]
www.topinnovations.com
[email protected]
V030910