Steel City 65110 User manual

User Manual
Read and understand this manual before using machine.
1 HP DUST COLLECTOR
STEEL CITY TOOL WORKS Manual Part No. OR70081
CUS
Model Number
65110
®

2
THANK YOU for purchasing your new Steel City Dust
Collector. This dust collector has been designed, tested, and
inspected with you, the customer, in mind. When properly
used and maintained, your dust collector will provide you
with years of trouble free service, which is why it is backed
by one of the longest machinery warranties in the business.
This dust collector is just one of many products in the Steel
City’s family of woodworking machinery and is proof of our
commitment to total customer satisfaction.
At Steel City we continue to strive for excellence each and
every day and value the opinion of you, our customer. For
comments about your dust collector or Steel City Tool Works,
please visit our web site at www.steelcitytoolworks.com .

3
TABLE OF CONTENTS
INTRODUCTION
This user manual is intended for use by anyone working with this machine. It should be kept available
for immediate reference so that all operations can be performed with maximum efficiency and safety.
Do not attempt to perform maintenance or operate this machine until you have read and understand the
information contained in this manual.
This Dust Collector is intended for use of wood dust removal only. Any other use is forbidden. This
machine is not to be modified for any reasons.
The drawings, illustrations, photographs, and specifications in this user manual represent your machine
at time of print. However, changes may be made to your machine or this manual at any time with no
obligation to Steel City Tool Works.
INTRODUCTION
SECTION 1 Warranty .................................................................................................................................................4
SECTION 2 Product Specifications ............................................................................................................................7
SECTION 3 Accessories and Attachments ................................................................................................................7
SECTION 4 Definition of Terms..................................................................................................................................7
SECTION 5 Feature Identification ..............................................................................................................................8
SECTION 6 General Safety........................................................................................................................................9
SECTION 7 Product Safety ......................................................................................................................................11
SECTION 8 Electrical Requirements........................................................................................................................12
SECTION 9 Unpacking & Inventory..........................................................................................................................15
SECTION 10 Assembly ..............................................................................................................................................17
SECTION 11 Operations ............................................................................................................................................20
SECTION 12 Maintenance .........................................................................................................................................21
SECTION 13 Troubleshooting ....................................................................................................................................22
SECTION 14 Parts List...............................................................................................................................................25

2 YEAR LIMITED WARRANTY
Steel City Tool Works, LLC (SCTW) warrants this SCTW machinery to be free of defects in workmanship and materials for a period
of 2 years from the date of the original retail purchase by the original owner for domestic use. Granite components are warranted for
2 years based on normal use and is void if non SCTW accessories are used that cause the break or chip. Customer must advise
SCTW within 30 days for any damage or defect found upon receipt of the product to qualify for the warranty on granite.
The warranty does not cover any product used for professional or commercial production purpose nor for industrial or educational
applications. Such cases are covered by our 1 year Limited Warranty with the Conditions and Exceptions listed below.
Conditions and exception:
Warranty applies to the original buyer only and may not be transferred. Original proof of purchase is required.
Warranty does not include failures, breakage or defects deemed after inspection by an Authorized Service Center, (ASC) or agent of,
have been directly or indirectly caused by or resulting from improper use, lack of or improper maintenance, misuse or abuse,
negligence, accidents, damage in handling or transport, or normal wear and tear of any part or component.
Additionally, warranty is void if repairs or alterations are made to the machine by an unauthorized service center without the direct
consent of SCTW
Consumables such as blades, knives, bits and sandpaper are not covered.
Wear items such as drive belt, bearings, switch, are covered for 1 year.
To file a claim of warranty or to find a service center, call toll free 877-724-8665 or email [email protected] and
you must be able to present the original or photo copy of the sales receipt including the serial number from the machine and/or carton.
SCTW will inspect, repair or replace, at its expense and its option, any part that has proven to be defective in workmanship or
material, provided that the customer returns the product prepaid to a designated ASC and provides SCTW with a reasonable
opportunity to verify the alleged defect by inspection. SCTW will return the product or replacement at our expense unless it is
determined by us that there is no defect or that the defect resulted from causes not within the scope of our warranty in which case we
will, at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be responsible
for the handling and shipping costs of the return.
SCTW furnishes the above warranties in lieu of all other warranties, express or implied. SCTW shall not be liable for any special,
indirect, incidental, punitive or consequential damages, including without limitation loss of profits arising from or related to the
warranty, the breach of any agreement or warranty, or the operation or use of its machinery, including without limitation damages
arising from damage to fixtures, tools, equipment, parts or materials, direct or indirect loss caused by and other part, loss of revenue
or profits, financing or interest charges, and claims by and third person, whether or not notice of such possible damages has been
given to SCTW. Damages or any kind for any delay by or failure of SCTW to perform its obligations under this agreement or claims
made a subject of a legal proceeding against SCTW more than one (1) year after such cause of action first arose.
The validity, construction and performance of this Warranty and any sale of machinery by SCTW shall be governed by the law of the
Commonwealth of Pennsylvania, without regard to conflicts of law’s provisions of any jurisdiction. Any action related in any way to
any alleged or actual offer, acceptance or sale by SCTW or any claim related to the performance of and agreement including without
limitation this Warranty, shall take place in the federal or state courts in Allegheny County, Pennsylvania.
Warranty registration card must be submitted to SCTW for purpose of proof within 90 days of purchase with a copy of the sales
receipt. Failure to do so will, revert the 2 year warranty to 1 year as in the terms stated above. This registration is also needed to
facilitate contact in case of a safety recall.
This warranty gives you specific legal rights and you may have other rights which vary in certain States or Provinces.
Note to user
This instruction manual is meant to serve as a guide only. Specification and references are subject to change without prior notice.
Check the website www.steelcitytoolworks.com for updated manuals with reference to the VER# located on the front page.
LIMITED WARRANTY – ACCU-SHOP line of bench top tools
Steel City Tool Works, LLC (SCTW) warrants this SCTW ACCU-SHOP machinery to be free of defects in workmanship and materials
for a period of 2 years from the date of the original retail purchase by the original owner for domestic use.
Consumables such as blades, knives, bits and sandpaper are not covered.
Wear items such as drive belt, bearings, switch, are covered for 1 year.
The warranty does not cover any product used for professional or commercial production purpose nor for industrial or educational
applications. Such cases are covered by our 30 days Limited Warranty with the Conditions and Exceptions listed previously.
WARRANTY
4

5
WARRANTY CARD
Name ________________________________________________
Street _______________________________________________
Apt. No. ______________________________________________
City _________________________ State ______ Zip __________
Phone Number_________________________________________
E-Mail________________________________________________
Product Description:_____________________________________
Model No.: ___________________________________________
Serial No. _____________________________________________
The following information is given on a voluntary basis
and is strictly confidential.
1. Where did you purchase your STEEL CITY machine?
Store: ____________________________________________
City:______________________________________________
2. How did you first learn of Steel City Tool Works?
___ Advertisement ___ Mail Order Catalog
___ Web Site ___ Friend
___ Local Store Other_______________________
3. Which of the following magazines do you subscribe to?
___ American Woodworker ___ American How-To
––– Cabinetmaker ___ Family Handyman
___ Fine Homebuilding ___ Fine Woodworking
___ Journal of Light Construction ___ Old House Journal
___ Popular Mechanics ___ Popular Science
___ Popular Woodworking ___ Today’s Homeowner
___ WOOD ___ Woodcraft
___ WOODEN Boat ___ Woodshop News
___ Woodsmith ___ Woodwork
___ Woodworker ___ Woodworker’s Journal
___ Workbench Other_________________
4. Which of the following woodworking / remodeling shows do
you watch?
___ Backyard America ___ The American Woodworker
___ Home Time ___ The New Yankee Workshop
___ This Old House ___ Woodwright’s Shop
Other__________________________________________
5. What is your annual household income?
___ $20,000 to $29,999 ___ $30,000 to $39,999
___ $40,000 to $49,999 ___ $50,000 to $59,999
___ $60,000 to $69,999 ___ 70,000 to $79,999
___ $80,000 to $89,999 ___ $90,000 +
6. What is your age group?
___ 20 to 29 years ___ 30 to 39 years
___ 40 to 49 years ___ 50 to 59 years
___ 60 to 69 years ___ 70 + years
7. How long have you been a woodworker?
___ 0 to 2 years ___ 2 to 8 years
___ 8 to 20 years ___ over 20 years
8. How would you rank your woodworking skills?
___ Simple ___ Intermediate
___ Advance ___ Master Craftsman
9. How many Steel City machines do you own? _____________
10. What stationary woodworking tools do you own?
Check all that apply.
___ Air Compressor ___ Band Saw
___ Drill Press ___ Drum Sander
___ Dust Collection ___ Horizontal Boring Machine
___ Jointer ___ Lathe
___ Mortiser ___ Panel Saw
___ Planer ___ Power Feeder
___ Radial Arm Saw ___ Shaper
___ Spindle Sander ___ Table Saw
___ Vacuum Veneer Press ___ Wide Belt Sander
Other____________________________________________
11. Which benchtop tools do you own?
Check all that apply.
___ Belt Sander ___ Belt / Disc Sander
___ Drill Press ___ Band Saw
___ Grinder ___ Mini Jointer
___ Mini Lathe ___ Scroll Saw
___ Spindle / Belt Sander Other______________________
12. Which portable / hand held power tools do you own?
Check all that apply.
___
Belt Sander ___ Biscuit Jointer
___ Dust Collector ___ Circular Saw
___ Detail Sander ___ Drill / Driver
___ Miter Saw ___ Orbital Sander
___ Palm Sander ___ Portable Thickness Planer
___ Saber Saw ___ Reciprocating Saw
___ Router Other_______________________
13. What machines / accessories would you like to see added to the
STEEL CITY line?
____________________________________________________
____________________________________________________
14. What new accessories would you like to see added?
____________________________________________________
____________________________________________________
15. Do you think your purchase represents good value?
___Yes ___ No
16. Would you recommend STEEL CITY products to a friend?
___ Yes ___ No
17. Comments:
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
CUT HERE

FOLD ON DOTTED LINE
FOLD ON DOTTED LINE
PLACE
STAMP
HER
SteelCityToolWorks
#4 Northpoint Court
Bolingbrook, IL 60440
E
6

7
PRODUCT SPECIFICATIONS
Motor Specifications:
Type Induction, Ball Bearing
Continuous Duty
Horsepower 1
Amps 8.5
Voltage 120
Phase Single
Hertz 60
RPM 3450 (no load)
Product Specifications:
Noise Level (Decibel) 87 dB
CFM 700
Static Pressure
(inches of water) 8.5
Number of ports 1
Port Diameter 4-inch (10.2cm)
Filter Bag Micron 1
Filter Bag Capacity 2.5 cubic feet
(88.5 cubic cm)
Collection Bag Micron Plastic
Product Dimensions:
Footprint 28-1/2” x 15-1/2” (72.4cm x 39.4cm)
Length 28-1/2” (72.4cm)
Width 15-1/2” (39.4cm)
Height 72” (1829cm)
Weight 79 Lbs. (36Kg)
Shipping Dimensions:
Carton Type Cardboard
Length 31-1/8” (79cm)
Width 17” (43cm)
Height 15-3/8” (39cm)
Gross Weight 84 Lbs. (38Kg)
DEFINITION OF TERMS
Dust Collector – A machine used to collect fine wood
dust and chips.
Dust Collection System – A dust collector connected
to multiple woodworking machines utilizing various
types of hose/pipe and fittings.
ACCESSORIES AND ATTACHMENTS
• Use only accessories recommended for this machine.
Using other accessories may cause serious injury and
cause damage to the machine.
Collection Bag Capacity 2.5 cubic feet
(88.5 cubic cm)
Collection Hose Type Flexible
Collection Hose Diameter 4-inch (10.2cm)
Collection Hose Length 6-foot (1.8 meter)
WARNING
!
Contact your local Steel City dealer for accessories, or
visit our website at: www.steelcitytoolworks.com.
Below are some terms that will help you to understand and setup your Dust Collector
and design your own Dust Collection System.
C.F.M. = Cubic Feet/Minute – A measurement of the
amount of air volume that can move through a dust
collector in one minute.
Static Pressure – A measurement of the amount of the
resistance to airflow in a dust collection system.
One Micron – One micron is equal to one millionth of a
meter.

8
FEATURE IDENTIFICATION
A. 4-inch Intake Port
B. 4-inch Flexible Hose
C. Filter Bag Hanger
D. Filter Bag
E. Collection Bag, Plastic
F Locking Band
G. Blower and Motor Assembly
H. Side Support
I. Base
J. Caster
Fig. 1-1
F
E
H
J
I
B
A
G
C
D

9
GENERAL SAFETY
NOTICE
CAUTION
Exposure to the dust created by power sanding, saw-
ing, grinding, drilling and other construction activities
may cause serious and permanent respiratory or
other injury, including silicosis (a serious lung dis-
ease), cancer, and death. Avoid breathing the dust,
and avoid prolonged contact with dust. The dust
may contain chemicals known to the State of
California to cause cancer, birth defects or other
reproductive harm.
2. ALWAYS wear eye protection. Any machine can
throw debris into the eyes during operations,
which could cause severe and permanent eye
damage. Everyday eyeglasses are NOT safety
glasses. ALWAYS wear Safety Goggles (that
comply with ANSI standard Z87.1) when operat-
ing power tools.
WARNING
!WARNING !
WARNING
!
WARNING
!
CAUTION
!
DANGER
!
!
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Always operate tool in well ventilated area and pro-
vide for proper dust removal. Use a dust collection
system along with an air filtration system whenever
possible. Always use properly fitting NIOSH/OSHA
approved respiratory protection appropriate for the
dust exposure, and wash exposed areas with soap
and water.
1. To avoid serious injury and damage to the machine,
read the entire Instruction Manual before assembly
and operation of this machine.
TO AVOID serious injury and damage to the machine,
read and follow all Safety and Operating Instructions
before assembling and operating this machine.
This manual is not totally comprehensive. It does not
and can not convey every possible safety and opera-
tional problem which may arise while using this
machine. The manual will cover many of the basic and
specific safety procedures needed in an industrial envi-
ronment.
All federal and state laws and any regulations having
jurisdiction covering the safety requirements for use of
this machine take precedence over the statements in
this manual. Users of this machine must adhere to all
such regulations.
Below is a list of symbols that are used to attract your
attention to possible dangerous conditions.
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety mes-
sages that follow this symbol to avoid possible injury or
death.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation, if not avoid-
ed, MAYresult in minor or moderate injury. It may also
be used to alert against unsafe practices.
CAUTION used without the safety alert symbol indi-
cates a potentially hazardous situation which, if not
avoided, may result in property damage.
This symbol is used to alert the user to useful informa-
tion about proper operation of the machine.

10
4. ALWAYS wear a NIOSH/OSHA approved dust
mask to prevent inhaling dangerous dust or air-
borne particles.
8. AVOID a dangerous working environment. DO
NOT use electrical tools in a damp environment
or expose them to rain.
9. CHILDPROOF THE WORKSHOP AREA by
removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks.
3. ALWAYS wear hearing protection. Plain cotton is
not an acceptable protective device. Hearing
equipment should comply with ANSI S3.19
Standards.
WARNING
!
WARNING
!
WARNING
!
WARNING
!
5. ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an area that have slip-
pery floor surfaces from debris, grease, and wax.
6. ALWAYS unplug the machine from the electrical
receptacle when making adjustments, changing
parts or performing any maintenance.
7. AVOID ACCIDENTAL STARTING. Make sure that
the power switch is in the “OFF” position before
plugging in the power cord to the electrical
receptacle.
10. DO NOT use electrical tools in the presence of
flammable liquids or gasses.
11. DO NOT FORCE the machine to perform an opera-
tion for which it was not designed. It will do a safer
and higher quality job by only performing operations
for which the machine was intended.
12. DO NOT stand on a machine. Serious injury could
result if it tips over or you accidentally contact any
moving part.
13. DO NOT store anything above or near the machine.
14. DO NOT operate any machine or tool if under the
influence of drugs or alcohol.
15. EACH AND EVERY time, check for damaged parts
prior to using any machine. Carefully check all
guards to see that they operate properly, are not
damaged, and perform their intended functions.
Check for alignment, binding or breakage of all
moving parts. Any guard or other part that is dam-
aged should be immediately repaired or replaced.
16. Ground all machines. If any machine is supplied
with a 3-prong plug, it must be plugged into a 3-
contact electrical receptacle. The third prong is
used to ground the tool and provide protection
against accidental electric shock. DO NOT remove
the third prong.
17. Keep visitors and children away from any machine.
DO NOT permit people to be in the immediate work
area, especially when the machine is operating.
18. KEEP protective guards in place and in working
order.
19. MAINTAIN your balance. DO NOT extend yourself
over the tool. Wear oil resistant rubber soled shoes.
Keep floor clear of debris, grease, and wax.
20. MAINTAIN all machines with care. ALWAYS KEEP
machine clean and in good working order. KEEP all
blades and tool bits sharp.
21. NEVER leave a machine running, unattended. Turn
the power switch to the OFF position. DO NOT
leave the machine until it has come to a complete
stop.
22. REMOVE ALL MAINTENANCE TOOLS from the
immediate area prior to turning the machine ON.
23. SECURE all work. When it is possible, use clamps
or jigs to secure the workpiece. This is safer than
attempting to hold the workpiece with your hands.

11
4. TO REDUCE the risk of electrical shock. DO
NOT use this machine outdoors. DO NOT
expose to rain. Store indoors in a dry area.
9. DO NOT handle the plug or dust collector with
wet hands.
24. STAY ALERT, watch what you are doing, and use
common sense when operating any machine. DO
NOT operate any machine tool while tired or under
the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
25. USE ONLY recommended accessories. Use of
incorrect or improper accessories could cause seri-
ous injury to the operator and cause damage to the
machine. If in doubt, DO NOT use it.
26. ONLY use a proper extension cord in good condi-
tion. When using an extension cord, be sure to use
one heavy enough to carry the current your
machine will draw.
27. Wear proper clothing, DO NOT wear loose clothing,
gloves, neckties, or jewelry. These items can get
caught in the machine during operations and pull
the operator into the moving parts. Users must
wear a protective cover on their hair, if the hair is
long, to prevent it from contacting any moving parts.
28. SAVE these instructions and refer to them frequent-
ly and use them to instruct other users.
29. Information regarding the safe and proper operation
of this tool is also available from the following
sources:
Power Tool Institute
1300 Summer Avenue
Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive
Itasca, IL 60143-3201
American National Standards Institute
25 West 43rd Street, 4th floor
New York, NY 10036
www.ansi.org
ANSI 01.1 Safety Requirements for
Woodworking Machines, and the U.S. Department
of Labor regulations
www.osha.gov
PRODUCT SAFETY
1. Serious personal injury may occur if normal safety
precautions are overlooked or ignored. Accidents
are frequently caused by lack of familiarity or failure
to pay attention. Obtain advice from supervisor,
instructor, or another qualified individual who is
familiar with this machine and its operations.
2. Every work area is different. Always consider safe-
ty first, as it applies to your work area. Use this
machine with respect and caution. Failure to do so
could result in serious personal injury and damage
to the machine.
3. Prevent electrical shock. Follow all electrical and
safety codes, including the National Electrical Code
(NEC) and the Occupational Safety and Health
Regulations (OSHA). All electrical connections and
wiring should be made by qualified personnel only.
5. STOP using this machine, if at any time you experi-
ence difficulties in performing any operation.
Contact your supervisor, instructor or machine serv-
ice center immediately.
6. Safety decals are on this machine to warn and
direct you to how to protector yourself or visitors
from personal injury. These decals MUST be main-
tained so that they are legible. REPLACE decals
that are not legible.
7. DO NOT leave the dust collector plugged into the
electrical outlet. Unplug dust collector from the out-
let when not in use and before servicing, changing
bags, unclogging and cleaning.
8. ALWAYS turn the power switch “OFF” before
unplugging the dust collector.
10. DO NOT use the dust collector to pick up flam-
mable or combustible liquids, such as gasoline.
NEVER use the dust collector near any flammable
or combustible liquids.
11. USE the dust collector to pick up wood materials
only. DO NOT use the dust collector to pick up
metal shavings, metal dust, or parts.
12. NEVER use the dust collector to dissipate fumes or
smoke. NEVER pick up anything that is burning or
smoking, such as cigarettes, matches or hot ashes.
WARNING
!
WARNING
!

12
18. DO NOT insert fingers or foreign objects into
the dust intake port. Keep hair, loose clothing,
fingers, and all body parts away from openings
and moving parts of the dust collector.
19. DO NOT use the dust collector without the dust
collection bag in place and properly secured.
20. ALWAYS use safety gates or caps to cover dust
ports when the dust collector is not in use or
mounted to a supporting surface for storage.
21. PERIODICALLY INSPECT dust bag for any cuts,
rips or tears. NEVER operate the dust collector with
a damaged bag or vacuum hose.
22. The dust collector is designed for home use or light
commercial duty ONLY.
23. CONNECT dust collector to a properly grounded
outlet only. See grounding instructions.
ELECTRICAL REQUIREMENTS
TO PREVENT electrical shock, follow all electrical and
safety codes, including the National Electrical Code
(NEC) and the Occupational Safety and Health
Regulations (OSHA). All electrical connections and
wiring should be made by qualified personnel only.
13. USE only as described in this manual. USE acces-
sories only recommended by Steel City.
14. DO NOT pull the dust collector by the power cord.
NEVER allow the power cord to come in contact
with sharp edges, hot surfaces, oil or grease.
15. DO NOT unplug the dust collector by pulling on the
power cord. ALWAYS grasp the plug, not the cord.
16. REPLACE a damaged cord immediately. DO NOT
use a damaged cord or plug. If the dust collector is
not operating properly, or has been damaged, left
outdoors or has been in contact with water.
17. DO NOT use the dust collector as a toy. DO NOT
use near or around children.
WARNING
!
WARNING
!TO REDUCE the risk of electrical shock, DO NOT use
machine outdoors. DO NOT expose to rain. Store
indoors in a dry area.
DO NOT connect the machine to the power source
before you have completed the set up process. DO
NOT connect the machine to the power source until
instructed to do so.

13
GROUNDING INSTRUCTIONS
Fig. 1-1
Fig. 1-2
WARNING
!
WARNING
!
This machine MUST BE GROUNDED while in use to
protect the operator from electric shock.
In the event of a malfunction or breakdown, GROUND-
ING provides the path of least resistance for electric
current and reduces the risk of electric shock. This
machine is equipped with an electric cord that has an
equipment-grounding conductor and a grounding plug.
The plug MUST be plugged into a matching electrical
receptacle that is properly installed and grounded in
accordance with ALL local codes and ordinances.
If a plug is provided with your machine DO NOT modify
the plug. If it will not fit your electrical receptacle, have
a qualified electrician install the proper connections to
meet all electrical codes local and state. All connections
must also adhere to all of OSHA mandates.
IMPROPER ELECTRICAL CONNECTION of the equip-
ment-grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or
without yellow stripes) is the equipment-grounding con-
ductor. DO NOT connect the equipment-grounding con-
ductor to a live terminal if repair or replacement of the
electric cord or plug is necessary.
Check with a qualified electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the tool is properly
grounded.
PLUGS/RECEPTACLES
•Electrocution or fire could result if this machine is
not grounded properly or if the electrical configura-
tion does not comply with local and state electrical
codes.
•MAKE CERTAIN the machine is disconnected
from power source before starting any electrical
work.
•MAKE SURE the circuit breaker does not exceed
the rating of the plug and receptacle.
The motor supplied with your machine is a 120 volt,
alternating current, 60 hertz, single phase motor. It is
shipped wired for 120 volt application. Never connect
the green or ground wire to a live terminal.
This tool is intended for use on a circuit that has an
electrical receptacle as shown in Figure 1-1. Figure 1-1
shows a NEMA approved 3-wire, 15 amp electrical plug
and receptacle that have a grounding conductor. If a
properly grounded electrical receptacle is not available,
an adapter as shown in Figure 1-2 can be used to tem-
porarily connect this plug to a 2-contact ungrounded
receptacle. The adapter has a rigid lug extending from it
that MUST be connected to a permanent earth ground,
such as a properly grounded receptacle box. THIS
ADAPTER IS PROHIBITED IN CANADA.

14
MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)
120 VOLT OPERATION ONLY
25’ LONG 50’ LONG 100’ LONG
0 to 6 Amps 18 AWG 16 AWG 16 AWG
6 to 10 Amps 18 AWG 16 AWG 16 AWG
10 to 12 Amps 16 AWG 16 AWG 14 AWG
EXTENSION CORDS
To reduce the risk of fire or electrical shock, use the
proper gauge of extension cord. When using an
extension cord, be sure to use one heavy enough to
carry the current your machine will draw.
The smaller the gauge-number, the larger the diameter
of the extension cord is. If in doubt of the proper size of
an extension cord, use a shorter and thicker cord. An
undersized cord will cause a drop in line voltage result-
ing in a loss of power and overheating.
WARNING
!
CAUTION
!
USE ONLY a 3-wire extension cord that has a 3-prong
grounding plug and a 3-pole receptacle that accepts the
machine’s plug.
If you are using an extension cord outdoors, be sure it
is marked with the suffix “W-A” (“W” in Canada) to indi-
cate that it is acceptable for outdoor use.
Make certain the extension cord is properly sized, and
in good electrical condition. Always replace a worn or
damaged extension cord immediately or have it
repaired by a qualified person before using it.
Protect your extension cords from sharp objects, exces-
sive heat, and damp or wet areas.

15
• The machine is heavy, two people are required to
unpack and lift.
• Use a safety strap to avoid tip over when lifting
machine.
Check shipping carton and machine for damage before
unpackaging. Carefully remove packaging materials,
parts and machine from shipping carton. Always check
for and remove protective shipping materials around
motors and moving parts. Lay out all parts on a clean
work surface.
Remove any protective materials and coatings from all
of the parts and the dust collector. The protective coat-
UNPACKING & INVENTORY
A. Motor and blower assembly
B. Filter bag
C. Collection bag, Plastic
D. Side support (2)
E. Support
F. 4-inch hose clamp (2)
G. Caster (4)
H. Intake port cap
I. Filter bag hanger
J. Lower support rod
K. Base
L. 4-inch flexible hose
M. Locking band (2)
Fig. 1-1
M
B
A
L
K
E
G
H
I
J
F
D
C
WARNING
!
WARNING
!
ings can be removed by spraying WD-40 on them and
wiping it off with a soft cloth. This may need redone
several times before all of the protective coatings are
removed completely.
After cleaning, apply a good quality paste wax to any
unpainted surfaces. Make sure to buff out the wax
before assembly.
Compare the items to inventory figures; verify that all
items are accounted for before discarding the shipping
box.
If any parts are missing, do not attempt to plug in the
power cord and turn “ON” the machine. The machine
should only be turned “ON” after all the parts have been
obtained and installed correctly. For missing parts,
contact Steel City at 1-877-SC4-TOOL.

16
Fig. 1-2
A. Hex nut 3/8-16 (4)
B. Lock washer 3/8” (4)
C. Lock washer 5/16” (12)
D. Hex nut 5/16-18 (9)
E. Hex head screw 5/16-18 x 5/8” (12)
A
B
D
E
C

17
ASSEMBLY
1. DO NOT assemble the Dust Collector until you are
sure the tool IS NOT plugged in.
2. DO NOT assemble the Dust Collector until you are
sure the power switch is in the “OFF” position.
3. For your own safety, DO NOT connect the machine
to the power source until the machine is completely
assembled and you read and understand the entire
Owner’s Manual.
SWIVEL CASTER TO
BASE ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
Fig. 1-1
1. Insert bolt (A) from swivel caster through one of the
four holes in the base (B), three are not shown. See
figure 1-1.
2. Place 3/8-16 hex nut and 3/8” lock washer (C) onto
bolt of swivel caster and tighten.
3. Repeat Steps 1, 2 and 3 for the remaining three
swivel caster assemblies.
1. Place the base (A) in an upright position.
See figure 2-1.
2. Align two holes in the wider end of side support (B)
with two holes (C) in the base.
3. Insert a 5/16-18 x 5/8” hex head screw with 5/16”
lock washer through each of the two holes in the
side support and base.
4. Place a 5/16-18 flange hex nut onto each screw
and tighten securely.
Fig. 2-1
Fig. 2-2
5. Repeat Steps 1, 2, 3, and 4 to assemble the
second side support. See figure 2-2.
C
A
B
SIDE SUPPORT ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
B
A
C
WARNING
!
WARNING
!

18
MOTOR AND BLOWER
TO BASE ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
1. Place motor and blower assembly and base on
their side with intake port pointing towards base.
Fig. 3-1
2. Align the four holes, two shown (A) on the top of
both side supports (B) with four holes in the motor
and blower assembly (C). See figure 3-1.
3. Place a 5/16” lock washer onto a 5/16-18 x 5/8” hex
head screw and insert the screw through the side
support and thread screw into tapped hole in the
motor and blower assembly. Do not completely
tighten.
4. Repeat this process for the remaining three holes;
tighten securely.
SUPPORT ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
1. Place the support (A) inside the two side supports
(B). MAKE CERTAIN THE SUPPORT IS
ATTACHED TO THE SIDE SUPPORTS CLOSEST
TO THE MOTOR. See figure 4-1.
2. Align the four holes (C) three shown, in the support
with the four holes in the side supports.
3. Insert a 5/16-18 x 5/8” hex head screw with a 5/16”
lock washer through the side support and support.
4. Place a 5/16-18 flange hex nut onto the 5/16-18 x
5/8” hex head screw. Do not completely tighten.
5. Repeat Steps 3 and 4 for remaining three holes
and tighten securely.
Fig. 4-1
B
CAB
B
A
C
(Blower housing not shown for clarity.)
WARNING
!WARNING
!

19
FILTER AND COLLECTION BAG
TO DRUM ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
1. Thread 5/16-18 hex nut (A) onto the end of lower
support rod (B). Thread lower support rod about 1/2
inch into the tapped hole (C) on top of the blower
and motor assembly. Tighten the 5/16-18 hex nut
on the lower support rod against the blower and
motor assembly. See figure 5-1.
2. Place the end of filter bag hanger into the mating
end of the lower support. Hook the loop on the top
filter bag onto hook of the filter bag hanger.
Fig. 5-1
Fig. 5-2
3. Insert locking band (D) through all the loops of filter
bag (E). Position the open end of the filter bag over
the top lip of the drum. Make certain the locking
band is positioned in the upper recessed channel
of the drum and fasten clamp (F) securely to drum.
See figure 5-2.
5. Place the collection bag over the lower lip of the
drum. Make certain the locking band is positioned
in the lower recessed channel of the drum and
fasten clamp securely to drum.
INTAKE PORT CAP
AND HOSE ASSEMBLY
MAKE CERTAIN THE DUST COLLECTOR IS
DISCONNECTED FROM THE POWER SOURCE.
1. Slide the collar of the intake port cap over intake
port. Make sure the collar is positioned to the back
if you intend to attach the hose at this time. See
figure 6-1.
2. Place 4-inch hose clamp (A) onto the end of 4-inch
flexible hose (B).
3. Slide the end of 4-inch flexible hose with 4-inch
hose clamp onto intake port and tighten securely.
IMPORTANT: When connecting a flexible hose to
intake port, DO NOT REMOVE THE INTAKE PORT
CAP COLLAR FROM THE INTAKE PORT. Slide
the collar of intake port cap further back when
attaching a flexible hose.
Fig. 6-1
B
A
C
DF
E
B
A
WARNING
!
WARNING
!

20
According to many OSHA, ANSI, STATE, and LOCAL
CODES, it is the Employers Responsibility to:
•PERMIT ONLY trained and authorized employees to
operate equipment.
•INSPECT AND MAINTAIN guards, safety devices
and start/stop controls.
•INSTRUCT, TRAIN and SUPERVISE the safe method
of work.
Serious personal injury may occur if normal safety pre-
cautions are overlooked or ignored. Accidents are fre-
quently caused by lack of familiarity or failure to pay
attention. Obtain advice from supervisor, instructor, or
another qualified individual who is familiar with the
machine and its operations.
Every work area is different. Always consider safety
first, as it applies to your work area. Use any machine
with respect and caution. Failure to do so could result
in serious personal injury and damage to the machine.
STOP using the machine, if at any time you experience
difficulties in performing any operation. Contact your
supervisor, instructor or machine service center immedi-
ately.
OPERATIONS
HELPFUL HINTS:
• Always run the largest appropriate diameter hose
as far as possible. Running a smaller diameter hose
will greatly reduce the C.F.M. at the tool, yielding
marginal dust collection.
• The use of a low rated micron filter and collection
bag can increase the effectiveness of your dust
collector in removing fine particles of dust.
• Determine if you are to use your Dust Collector in a
Dust Collection System or as a direct hook-up to an
individual tool. If used in a Dust Collection System,
review Static Pressure Requirements.
To protect yourself from a static shock, ground the
dust collection system to a known ground.
If using the Dust Collector in a Dust Collector
System, make certain to:
• Ground the dust collection system to a known
ground.
• Always keep blast gates closed to unused tools.
• Make all runs as short as possible, minimizing the
number of bends or turns that could greatly reduce
the efficiency of your Dust Collector.
• Position the tools that have the highest C.F.M.
requirements closest to the Dust Collector.
THINGS TO CONSIDER:
• What is the maximum C.F.M. required for each tool
you intend to use? Your Dust Collector should be
rated for the tool that has the highest C.F.M.
requirement.
• Will two or more tools be running at the same time?
The Dust Collector should be rated to handle the
combined C.F.M. requirements of all operating tools.
CHILDPROOF THE WORKSHOP AREA by
removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks.
LOCKING SWITCH IN
THE "OFF" POSITION
When the Dust Collector is not in use, the switch key
should be removed so that it cannot be started. Grasp
the switch key and pull it out of the switch assembly.
With the switch key removed, the switch will not oper-
ate. However, should the switch key be removed while
the dust collector is running, it can be turned “OFF
” , but
cannot be restarted without inserting the switch key.
ON/OFF SWITCH
The ON/OFF switch assembly is located on the side of
the motor. To turn the dust collector “ON”, move the
switch up to the “ON” position. To turn the dust collector
“OFF”, move the same switch down to the “OFF”
position.
WARNING
!
WARNING
!
WARNING
!