STEEL HORSE AUDIO ST200 User manual

ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN, CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING STEEL HORSE AUDIO!
Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR
DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED.
ENSURE THA T THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1Classic 200W Compact Motorcycle Amplifier 21" Handlebar Clamp/Bracket
1G-Series 4" Pioneer Speakers in Waterproof housings 21-1/4" Handlebar Clamp/Bracket
1Amplifier Wire Harness
13.5mm (headphone) to RCA (amplifier) cable
6Cable Ties

PAGE 2
ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN, CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
-CONTINUED-
THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES THIS COPY AND IS AWARE
OF ITS IMPORTANCE FOR FUTURE USE.
WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE POINT WHERE IT IS
CONNECTED TO THE VEHICLE’S BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS
BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT.
THE END USER’S SAFETY DEPENDS UPON PROPER INSTALLATION OF THIS PRODUCT. IF A STEP IN THESE INSTRUCTIONS IS NOT
WITHIN YOUR CAPABILITIES OR YOU DO NOT HAVE THE CORRECT TOOLS, HAVE YOUR DEALER PERFORM THE PROCEDURE. IMPROPER
INSTALLATION OF THIS PRODUCT COULD RESULT IN DEATH OR SERIOUS INJURY.
ACCIDENTAL VEHICLE START-UP COULD CAUSE DEATH OR SERIOUS INJURY, REMOVE THE MAIN FUSE BEFORE PROCEEDING.
INTRODUCTION
Thank you for purchasing this Steel Horse Audio ST200 Motorcycle Speaker System that is designed to work with any audio devices with a
headphone jack including iPhone® and Android® smartphones and tablets. This easy to install and use, all in one unit is capable of transforming
your mobile audio device or phone into the center of your motorcycle’s audio system. Designed to mount on any motorcycle handle bars with a 1"
or 1-1/4” diameter (other sizes available upon request for 7/8", 1-1/8" and 1-1/2"). Congratulations and enjoy the ultimate audio experience!
FEATURE S
AMPLIFIER SPECS:
•Compatible with any audio device or phone with a headphone jack, including Android & iPhone
•Easy to install with simple wiring to speakers and power
•Adjustable gain and variable crossover (L/OFF/H)
•Measures just 1.5" x 2.5" x 4" for easy mounting
•Includes power, ground, remote on/off (to prevent battery drain) and output connections 4"
SPEAKER SPECS:
•Steel housings with triple plate chrome or satin black finish
•Measures 4.75" Diameter by 3" depth mounting size for easy mounting, even behind a windshield
•Includes two pair of bar mount brackets: 1” and 1-1/4” (1-1/2" available upon request)
•200 Watts Peak RMS Power | ~5 amps power draw
INSTALLATION
STEP 1
The Steel Horse Audio ST200 Classic Edition Motorcycle Speaker System can be used with any 12-
volt battery and can be mounted to a variety of bars using the included hardware. Mount the
speakers where they have sufficient clearance, position the speakers so the speakers are
directly at the rider.
MOUNT BRACKETS TO HANDLEBAR FIRST, THEN INSTALL SPEAKERS
Determine the diameter of the handlebar and use either the 1” Bracket or the 1-1/4” Bracket
Note: If you have a different diameter handlebar (7/8", 1-1/8" or 1-1/2"), please request that
bracket separately from us.

PAGE 3
ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN, CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
STEP 2
STEP 3
STEP 4
STEP 5
Install brackets on handlebars where speakers do not obstruct the riders view (such as the
handlebars, engine guards or highway/crash bars). Use allen screws that are included on the
bracket. The brackets themselves will tighten to the bar when the speakers are installed
Once brackets are installed, add the speakers:
A) Remove the nut and lock washer only and feed the speaker wire through the bracket hole and
attach each speaker to the bracket. Put the lock washer and nut back on through the wire and
tighten speaker to bracket. (Flat washer and lock washer go on the bottom). Do not over-tighten!
Adjust the speakers so they are directed at the rider’s head. To adjust, just slightly loosen the nut
on the speaker stem and move the speaker up or down to align. Make sure all screws are
securely fastened and tightened.
Route speaker wires through the bike’s frame to where the amplifier will be installed and
proceed to the next steps in amplifier and power connection.
SECURE THE WIRING AWAY FROM MOVING PARTS, PINCH POINTS, OR EXTREME HEAT. STEEL
HORSE AUDIO WILL NOT PROVIDE WARRANTY COVERAGE ON ANY ELECTRICAL COMPONENT
THAT FAILS DUE TO PINCHED, CRIMPED, BROKEN, ABRADED, MELTED, OR FRAYED WIRES.
AMPLIFIER & POWER CONNECTION
STEP 1
STEP 1
AMPLIFIER MOUNTING
Find a place to mount the amplifier away from direct exposure to the elements such as a tool
compartment, under the seat, fork bag, saddlebag, swing arm bag, windshield bag, etc. Most
places will be fine, but try to avoid areas that could cause extreme overheating (such as tight
places wrapped in foam or cotton). The amp can get some moisture but is not waterproof!
Note: Keep the included fuse off the fuse holder until all wiring connections have been made
and secured.
AMPLIFIER POWER CONNECTION
Connect the Red power wire (w/ fuse) from the wire harness to the positive terminal on the
battery. The Black wire is a ground wire and needs to be attached to the negative terminal on
the battery. (or to the vehicle’s chassis where paint has been removed. The shorter the wire, the better)
Take the ORANGE remote-on wire and run it to to a switched power source (headlight, taillight, etc) or to
Bluetooth® Receiver + Controller Add-on (purchased separately). If orange, black & red wires are not
connected, system will NOT work.
*When plugging the harness in to the amp, be sure to match up the plug for ORANGE with (R) for
"Remote" and RED to (B+) (Battery 12v+). It should lock in place.
-CONTINUED-
STEP 2

PAGE 4
ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN,CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
STEP 1
STEP 2
STEP 1
STEP 1
Speaker to Amplifier connection
Connect the speaker wires to the corresponding wires on the amplifier as follows:
Connect the stripped black wire (-) from the right speaker to the green stripped wire from the amp.
Connect the solid black wire (+) from the right speaker to the solid green wire from amp.
Connect the stripped black wire (-) from the left speaker to the stripped black wire from the amp.
Connect the solid black wire (+) from the left speaker to the solid black wire from amp.
Connect the music source or audio device
You can connect any audio device with a headphone jack using the included RCA to 3.5mm cable.
Connect RCA end to amplifier RCA inputs & other end to headphone port of your audio device/
mobile. Note: Please note with this type of connection, the audio source will control the volume of
the system.
*If you added a music source option, please follow these steps:
Bluetooth Controller (Satechi) - Follow instructions included with the controller to pair to your
Bluetooth® audio device. Once paired, mount it to your handlebars using the included mount. Plug
your audio device into the system using the RCA to 3.5mm cable and this controller will adjust the
volume and tracks on your audio device wirelessly. Follow the included instructions for operation.
Bluetooth Receiver + Controller (MTX) - Take the ORANGE remote-on wire from the amplifier and
run it to where you will install your Bluetooth controller. The system will turn on and off using the
controller. (It will also turn Off automatically after 5 minutes, when there is no active Bluetooth
device connection, to prevent battery drain). Next, mount the controller to the handlebars using
one of the included mounts. Run the red (+) wire to battery positive and black (-) wire to battery
negative (or to the vehicle’s chassis where paint has been removed, the closer, the better).
Connect the blue remote-on wire to the orange wire from the amp (from step 3). Connect the
included 3.5mm to the female output on the Bluetooth controller and connect the other end to
female input on the amplifier. Follow the included instructions for operation.
-CONTINUED-
STEP 3
STEP 4
STEP 1
Connect the Black wire with Dashes (-) from the RIGHT speaker to the green/white wire from the amp
Connect the Solid Black wire (+) from the RIGHT speaker to the solid green sire from the amp
Connect the Black wire with Dashes (-) from the LEFT speaker to the Black/White wire from the amp
Connect the Solid black wire (+) from the LEFT speaker to the solid black wire from the amp

PAGE 5
ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN, CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
STEP 1 When first listening to your system, you will need to adjust the levels and/or EQ on
your audio device as well as the amplifier gain level. We recommend starting the
gain at about half way and slowly turning it up until you reach optimal sound quality.
The amplifier variable crossover switch should always be at H (more volume, less
bass) or Off (more bass, less volume) setting
.HHSWKHDPSOLILHULQSXWKHDGSKRQHMDFNIURPWRXFKLQJDQ\EDUHPHWDOZKHQWKHUH
LVQRGHYLFHSOXJJHGLQWRWKHMDFNRU\RXPD\JHWVWDWLFRUSRSSLQJ WKURXJKWKH
VSHDNHUVZKHQWKHELNHLVRQ
-CONTINUED-
FINAL STEPS
STEP 2
Keep the amplifier input cable (headphone jack to RCA) from touching any bare metal when
there is no device plugged into the jack, or you may get static or popping through the speakers
when the bike is on.

PAGE 6
ST-200 REV A 1/4/17
ST200 CLASSIC EDITION WITH AUX-IN, CHROME ST200
STEELHORSEAUDIO.COM
800-823-5310 | [e-mail]
Steel Horse Audio #237 | 1540 Main St, Bldg 218 | Windsor, CO 80550
INSTALLATION INSTRUCTIONS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
5-YEAR WARRANTY
Steel Horse Audio warrants that any Steel Horse Audio products sold hereunder, shall be free of defects in materials & workmanship for a period of five
(5) years from the date of purchase by the consumer excepting the following provisions:
1. Steel Horse Audio shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the
product(s).
2. The product must be properly installed, maintained & operated under normal conditions.
3. Steel Horse Audio shall not be liable for any consequential & incidental damages, including labor & paint, resulting from failure of a Steel Horse
Audio product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Steel Horse Audio
& a customer.
4. Steel Horse Audio products are often intended for use in specific applications. Steel Horse Audio makes no warranty if used in applications other than
intended.
5. Steel Horse Audio speaker systems are warranted for five (5) years from the date of purchase by the consumer.
6. All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller
shall not carry a Steel Horse Audio warranty. If unsure, please contact the place of purchase to verify they are an authorized Steel Horse Audio
reseller.
RETURN POLICY
Merchandise may be returned up to 60 days from the date of purchase. Returns must be processed through original seller. Returned merchandise for any other reason other
than warranty claims must be in like new condition & subject to a 20% restocking fee. All returns are subject to inspection for determination of full or partial credit. Any
returned part that shows evidence of being used or installed contrary to manufacturer’s instructions, &/or subjected to improper handling, packaging orreturn shipping by
the customer, will not beeligible for exchange, refund orwarranty consideration. All returned electrical items will beinspected & tested. If electrical item is deemed
functional, no credit will be issued & item will be returned. All sales are final on discontinued or closeout merchandise.
©2015 STEEL HORSE AUDIO, LTD. ALL RIGHTS RESERVED
Listed Manufacturers and product model names are for reference only. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or
endorsement by them. All specifications are subject to change without notice.
-CONTINUED-