STEIN GEORGIA User manual

GEORGIA SQUARE
SHOWER - 2 SIDED
INSTALLATION INSTRUCTIONS
DEC 2014 | V2

1
GEORGIA SQUARE
SHOWER - 2 SIDED
INSTALLATION INSTRUCTIONS
PLEASE READ CAREFULLY
GENERAL INFORMATION
Thank you for choosing Stein Bathroomware. When you receive your Georgia Square Shower
package please check for any damage. If damage has occurred advise your supplier
immediately and do not proceed with installation.
DISCLAIMER
Stein International Ltd are not liable for any Georgia Square shower unit that has not been
installed correctly.
GLASS WARRANTY CLAIMS
Glass breakages on site are not replaced under warranty.
SAFETY GUIDE
• The glass requires two people to handle.
• Always stand glass up after unpacking the components and use soft packing when in
contact with hard surfaces. Take care not to strike an edge or corner on a hard surface.
• All glass is toughened and cannot be reworked or drilled.
• Wear protective gloves and eye protection.
• Special care should be taken when drilling walls to avoid hidden pipes or electrical cables
TOOLS REQUIRED
• Soft pencil and masking tape
• Spirit level and large square
• Screwdrivers
• Tape measure
• Drill and bits
• Hammer
MATERIALS REQUIRED
• Sika Silaex NG Translucent
• Rags and suitable cleaning materials
WE RECOMMEND THAT A PROFESSIONAL SHOWER INSTALLER IS USED FOR
INSTALLATION OF THIS PRODUCT TO ENSURE THE BEST RESULTS

1
2
3
4
5
6
1
5
3
7
2
6
4
8
9
7 8
2
Before commencing installation, please ensure you have the following components in your
package to complete installation.
Door front assembly channel x1
Fixed panel wall channel x1
Fixed return panel x1
Door front assembly x1
Handle set x1
Fixed panel screws 8mm x15
Fixed panel screw caps x8
Wall jamb xing screws 35mm x8
Corner channel - front door only installation x1
PACKAGE CONTENTS
ASSEMBLY DIAGRAM
Qty.Tick Ref Contents

3
SHOWER TYPE FRONT PANEL (A) MIN/MAX RETURN PANEL (B) MIN/MAX
900x900 Two Sided 830mm to 885mm 835mm to 865mm
1000x1000 Two Sided 930mm to 985mm 935mm to 965mm
1200 x 1000 Two Sided 1140mm to 1195mm 935mm to 965mm
WALL
CHANNEL
WALL
CHANNEL
BA
B A
LAYOUT PLAN
IMPORTANT:
• A & B measurements are the minimum outer boundary line of glass channels.
• Measurements are based on the oor being level, walls plumb and all surfaces at. Any
variations must be taken into account when marking out the position within the minimum to
maximum range.

checked
checked
checked
checked
checked
checked
PREPARATION CHECKLIST
THE FOLLOWING ITEMS MUST BE COMPLETED PRIOR TO INSTALLATION
Solid xing must be provided in the walls behind the wall channels. Refer to the
‘Layout Plan’ on page 3 to establish your shower type.
To ensure a successful result, the walls must be plumb and the oor at and level.
Contract a plumber to ensure waste tting is correctly installed.
ACRYLIC INSTALLATION OPTION
To install acrylic tray and liner, please refer to separate installation instructions with
packaged with product.
TILE INSTALLATION OPTION
Wall and oor surfaces must be waterproofed by a Certied Applicator and a Producer
Statement provided for the local council.
All tiling must be completed and allowed to cure before installing the shower enclosure.
4
1
3
2
INSTALLATION OF GEORGIA SQUARE SHOWER - 2 SIDED
Go to the Layout Plan on Page 3 and identify the shower type you are installing. Mark
out the outside line positioning of the wall channels within the minimum to maximum
range to suit your requirements.
Using these points mark out the position of the Front Door Assembly Channel (1) and
the Fixed Return Panel (3) onto the tray.
Mark the outside line and the wall channels (1) and (2) with a spirit level. Through the
holes in the channel pre-drill the start of the hole as a guide (refer Diagram A1).
Apply a bead of silicone down the back of the channels (1) and (2) and x in place with
screws (8) checking that they remain plumb (refer Diagram A2).
DIAGRAM A:
A1 A2

5
Slide Fixed Return Panel (3) and Door Assembly (4) into Wall Channel (1).
Hint: Insert the top or bottom corner of the panel into the channel rst. Then the rest
of the panel will slide into the channel easier.
Slide the Fixed Return Panel (3) over the extrusion on to the Front Door Assembly (4) at
the leading corner. Ensure this is aligned correctly then drilled and screwed.
DIAGRAM B:
DIAGRAM C:
5
4
DRILL HERE
THEN FIX
HERE
AERIAL VIEW

6
Using the sliding rails within the Front Door Assembly adjust them (in or out) to have
both the Fixed Return Panel and Front Door Panel positioned on the boundary line. They
should be positioned evenly between both wall channels.
Drill and fasten off the bottom rail on the inside (Diagram D1). Using a level ensure the
front assembly and return panel are plumb vertically at the corner junction and drill and
fasten the top rail (Diagram D2).
Drill four equally spaced 3.2mm holes into the wall channels (1) and (2) on the INSIDE of
the screen.
Make sure that your drill holes are more than 20mm back from the glass edge when using
the smallest screen size. Otherwise you risk breaking the glass.
Make sure that all the holes go though both the aluminium of the xed side panel and
the door front assembly. Fix off wall channels (1) and (2) to xed side panels (3) and (4)
using the xed panel screws (6) and covering them with screw caps (7).
6
6
DIAGRAM D:
DIAGRAM E:
D1 D2
DRILL 3.2 HOLES BETWEEN THE END OF
THE FIXED GLASS AND END OF DOOR.
FRONT VIEW OF SHOWERINSIDE SHOWER VIEW
ONLY ONE
HOLE IN
BOTTOM RAIL
SLIDING
RAIL
SLIDING
RAIL
20MM
DRILL HERE
OUTSIDE OF SHOWER

7
Handle Assembly: Screw the threaded rod into the handle.
Slide top post on to the the threaded rod,
making sure the post is facing the right
way.
Put standard screw into cap base, then
into washer, then into lower hole in the
glass. On the other side of the glass, slide
lower post onto the standard screw
making sure the post faces the right way.
Bring the handle up to the glass allowing
the top post to locate into the hole in the
glass. Fix the knob onto the threaded rod
making sure the washer is between the
glass and the knob.
Line up the hole in the handle with the
standard screw and post assembly. Screw
tightly together.
Place cap over base.
Apply silicone sealer around all external joints of shower screen a minimum of 24 hours
for silicone to set.
Silicone is not used on the inside of the shower screen because water can build up over
time within the wall channel and leak out of the shower area. The screen is designed to
allow the water to return into the shower area, if any is present. SCREENS THAT ARE
SEALED ON THE INSIDE WILL VOID WARRANTY.
7
8
1
2
3
4
5
6
SILICONE SEAL
TO OUTER EDGE

113 Newton Street, Mount Maunganui
Freephone 0800 002 299
Phone [phone]
www.stein.co.nz