STEINEL Combi Check 1.2 User manual

Spannungsprüfer
Combi Check 1.2
Master Check 3.2
D
GB
F
NL
I
E
S
FIN
DK
N
Bedienungsanleitung
Operating instructions
Mode d’emploi
Gebruiksaanwijzing
Istruzioni per l’uso
Instrucciones de manejo
Bruksanvisning
Brugsanvisning
Käyttöohje
Bruksanvisning
All manuals and user guides at all-guides.com
all-guides.com

CKonformitätserklärung
Das Produkt erfüllt die
Niederspannungsrichtlinie 73/23/EWG und die EMV- Richtlinie 89/336/EWG.
Funktionsgarantie
Dieses STEINEL-Produkt ist
mit größter Sorgfalt hergestellt,
funktions- und sicherheitsge-
prüft nach geltenden Vor-
schriften und anschließend
einer Stichprobenkontrolle
unterzogen.
Die Garantiefrist beträgt
36 Monate und beginnt mit
dem Tag des Verkaufs an den
Verbraucher. Wir beseitigen
Mängel, die auf Material- oder
Fabrikationsfehlern beruhen,
die Garantieleistung erfolgt
durch Instandsetzung oder
Austausch mangelhafter Teile
nach unserer Wahl.
Eine Garantieleistung entfällt
für Schäden an Verschleiß-
teilen, für Schäden und Män-
gel, die durch unsachgemäße
Behandlung oder Wartung
auftreten sowie für Bruch bei
Sturz.
Weitergehende Folgeschäden
an fremden Gegenständen
sind ausgeschlossen. Die
Garantie wird nur gewährt,
wenn das unzerlegte Gerät mit
Kassenbon oder Rechnung
(Kaufdatum und Händler-
stempel), gut verpackt, an die
zutreffende Servicestation ein-
gesandt oder in den ersten
6 Monaten dem Händler über-
geben wird.
Reparaturservice:
Nach Ablauf der Garantiezeit
oder Mängeln ohne Garantie-
anspruch repariert unser
Werkservice. Bitte das
Produkt gut verpackt an die
nächste Servicestation
senden.
8
Zuschaltbare Prüfspitzenbeleuchtung
(nur Combi Check 1.2)
Die Prüfspitzenbeleuchtung
kann manuell durch Drücken
der Taste und einmaliges
Kurzschließen der Prüfspitzen
eingeschaltet werden. Die
Beleuchtung bleibt nur für
die Dauer der Tastenbetäti-
gung eingeschaltet.
Combi Check 1.2
햲Test probe guard
햳Test probes
햴Voltage indicator, LED
햵Pushbutton
햶Clip connector
햷LED's for indicating
쎻
aDC and AC voltage
쎻bpolarity
쎻
ccontinuity testing
쎻dphase testing
(Combi Check 1.2
only)
햸Battery compartment
햹Accoustic indicator, buz-
zer (Combi Check 1.2
only)
햺Test probe light
(Combi Check 1.2 only)
Master Check 3.2
햲Test probe guard
햳Test probes
햴Voltage indicator, LED
햵Pushbutton
햶Clip connector
햷LED's for indicating
쎻
aDC and AC voltage
쎻bpolarity
쎻
ccontinuity testing
햸Battery compartment
Dear Customer
Congratulations on purchas-
ing your new STEINEL
Voltage Tester and thank you
for the confidence you have
shown in us. You have cho-
sen a high-quality product
that has been manufactured,
tested and packed with the
greatest care. The step volt-
age tester is capable of the
following functions:
– DC and AC voltage indica-
tion
– Polarity indication
– Continuity testing with
pushbutton
– Voltage detection > 50 V
AC / 120 V DC even with-
out batteries
– Automatic battery monitor-
ing
– Single-hand operation for
testing socket outlets using
clip connector for test pro-
bes
– Phase testing
(Combi Check 1.2 only)
– Visual and accoustic
indicator (Combi Check 1.2
only)
– Selectable test probe light
(Combi Check 1.2 only)
Description
Instructions for Use
GB
9
All manuals and user guides at all-guides.com

Technical Specifications
Battery and Function Test
Dimensions: (L x W x H) 230 x 55 x 34 mm
Rated voltage range: Combi Check 1.2: 6–690 V AC/DC
Master Check 3.2: 6–400 V AC/DC
Frequency range: 0–100 Hz;
AC display from f > 2 Hz
Voltage surge proof: Combi Check 1.2: 6 KV
Master Check 3.2: 4 KV
Input resistance: > 300 kOhm
Input current: Combi Check 1.2: Is < 2.5 mA at 690 V
Master Check 3.2: Is < 2.5 mA at 400 V
Continuity testing: Continuity < 500 kOhm
Single-pole phase testing:
Continuity at voltages
(Combi Check 1.2 only)
> 90 V AC (acoustic signal)
Temperature range: – 10 °C to + 55 °C
Battery life: approx. 1500 operations
Battery type: 2 x micro 1.5 V AAA Alkaline
(do not use rechargeable batteries)
Enclosure: IP 50
Approval: to EN 61243-3
= VDE 0682 Part 401
Weight: 135 g
Battery installation:
Open the battery compart-
ment using a screwdriver or
a coin. With the rear side of
the unit facing up, turn the
catch clockwise through 45°
to unlock. Now pull the bat-
tery compartment out as far
as the stop. Install batteries
as indicated (do not use
rechargeable batteries). To
close the battery compart-
ment, push the battery com-
partment as far as it will go
into the housing and lock the
compartment in place by
turning the catch anticlock-
wise through 45°.
WARNING: Voltage tester
must not be used with the
battery compartment open.
Function test/battery test
With the test probes shorted
and pushbutton pressed the
entire LED step display must
come on briefly, leaving only
the +6 V step indicator on.
An acoustic signal will also
sound. If the +6 V step indi-
cator flashes during this test,
change the batteries at the
next opportunity possible.
The LED step display will
flash while conducting further
voltage/continuity checks to
remind you that the batteries
need changing.
11
Safety Instructions
ç y
The voltage tester must
only be used within the
specified rated voltage
range. The provisions con-
tained in DIN VDE 0105
Part 100 and EN 50110-1
regarding the use of volt-
age testers stipulate that
just before testing for iso-
lation from supply, the
voltage tester must be
checked for proper work-
ing order. If the indicator
fails to operate during this
check, the voltage tester
must not be used.
y
Indication that the upper
limit for extra-low voltages
(ELV) has been exceeded
only serves as a warning
to the user and not as a
measurement reading.
y
Due to the high input
resistance, the capacitive
and inductive voltages
may be indicated.
yWhen testing, hold the
voltage tester by its hand-
les only. Do not touch the
test electrodes. Only per-
form 2-pole voltage tests.
y
Before using the voltage
tester in places where
noise levels are high,
first check whether the
accoustic test signal is
audible.
y
The LEDs start to glow at
80-85 % of designated
voltage.
y
Reliable indication is only
assured over a tempera-
ture range of –10 °C to
+55 °C.
y
The voltage tester must be
checked for proper work-
ing order shortly before
and after testing for isola-
tion from supply. If this
check reveals any failure
of the tester to indicate
one or more steps or if the
voltage tester fails to show
that it is ready for opera-
tion, it must not be used.
y
The voltage tester and its
accessories must not be
dismantled by unauthor-
ized persons.
y
The tester must be stored
in a dry and clean place.
y
The tester must not be
used in wet conditions
(e.g. condensation or rain)
(IP 50).
y
Within its maximum ON
duration, the device may
be exposed for up to 30
seconds to the maximum
rated voltage of the indi-
cated range.
y
Indicator legibility may be
impaired in adverse light
conditions, e.g. in sunlight.
y
WARNING: Voltage tester
must not be used with the
battery compartment open.
GB
10
All manuals and user guides at all-guides.com

Phase testing
(Combi Check 1.2 only)
WARNING: Phase testing
cannot be performed in
unfavourable locations, e.g.
on ladders with wooden
rungs or in rooms with insu-
lated floor coverings and in
AC voltage systems not
properly bonded to earth.
y
To perform the phase test,
contact the small test
probe with the phase
(> 90 V AC) of the AC
voltage system and touch
the phase tester contact
on the indicator handle
with your thumb. The 6 V
step indicator (+ and –)
will light up upon phase
contact and an acoustic
signal is also given.
13
Semiconductor testing
When the button is pressed
during polarity-dependent
continuity testing, the internal
test voltage source is
switched to the test probes.
The display handle repre-
sents the positive pole, and
the small handle the negative
pole. If continuity is given, the
+6 V diode illuminates. An
acoustic indication is also
given for Combi Check 1.2.
incorrectcorrect
Voltage testing
햲Apply the test probes to
the potential points you
wish to test.
y
For DC voltage testing, the
test probe on the display
handle represents the
positive pole, and the
small test probe the neg-
ative pole.
y
The positive and the neg-
ative diode of the 6 V volt-
age step will light up
simultaneously for AC
voltage.
y
The entire LED step dis-
play will briefly light up at
the start of each voltage
test.
햳The level of voltage pre-
sent is indicated by the
LED's lighting up as far as
the step level of voltage
present. An acoustic indi-
cation is also given for
Combi Check 1.2.
Continuity testing
햲Before conducting a con-
tinuity test in electrical
systems, first switch off
external voltage sources
and, where applicable,
discharge capacitors.
햳Short the test probes and
keep button pressed.
햴Contact the test object
with the test probes.
Contact the test object
with the test probes. If
contact resistance is
< 500 kOhms, the +6 V
diode will light up.
An acoustic indication is also
given for Combi Check 1.2.
Impressed external voltages
will be indicated despite the
continuity test, and will not
harm the tester.
12
All manuals and user guides at all-guides.com

CDeclaration of Conformity
This product complies with
Low Voltage Directive 73/23/EEC and EMC Directive 89/336/EEC.
Functional Warranty
This STEINEL product has
been manufactured with
great care, and its operation
and safety have been tested
in conformity with the current
regulations. Production is
also submitted to final ran-
dom-sample testing.
The warranty period is
36 months, starting on the
date of sale to the user. We
undertake to remedy faults
caused by material or manu-
facturing defects. This war-
ranty undertaking shall be
performed by the repair or
replacement of the defective
parts, at our own discretion.
This warranty shall not cover
damage to wearing parts or
damage and faults caused
by incorrect operation or
maintenance. Breakage due
to a fall is also not covered.
Further consequential dama-
ge to external items is ex-
cluded.
Claims under warranty shall
only be accepted if the pro-
duct is sent fully assembled
and well packed complete
with sales slip or invoice
(date of purchase and dea-
ler’s stamp) to the appro-
priate Service Centre or
handed in to the dealer
within the first 6 months.
Repair Service:
Our Customer Service
Department will repair faults
not covered by warranty or
after the warranty period.
Please send the product well
packed to your nearest
Service Centre.
14
Selectable test probe light
(Combi Check 1.2 only)
The test probe light can be
switched on manually by
pressing the button and
briefly shorting the test pro-
bes. The light only remains
on while the button is
pressed.
Combi Check 1.2
햲Protection des pointes de
test
햳Pointes de test
햴Témoin de tension, DEL
햵Poussoir
햶Cran
햷Diodes pour l’affichage
de:
쎻
atensions continues et
alternatives
쎻bpolarité
쎻
ctest de continuité
쎻dtest de phase (uni-
quement Combi
Check 1.2)
햸Compartiment à piles
햹Avertisseur sonore
pour signal acoustique
(uniquement Combi
Check 1.2)
햺Éclairage des pointes de
test (uniquement Combi
Check 1.2)
Master Check 3.2
햲Protection des pointes de
test
햳Pointes de test
햴Témoin de tension, DEL
햵Poussoir
햶Cran
햷Diodes pour l’affichage
de:
쎻
atensions continues et
alternatives
쎻bpolarité
쎻
ctest de continuité
햸Compartiment à piles
Cher client,
Nous vous remercions de la
confiance que vous avez
témoignée à STEINEL en
achetant ce testeur de ten-
sion. Vous avez choisi un
article de très grande qualité,
fabriqué, testé et conditionné
avec le plus grand soin. Le
testeur de tension vous offre
les fonctions suivantes:
– affichage de tensions con-
tinues et alternatives,
– affichage de la polarité,
– test de continuité avec
poussoir,
– détection de tensions
> 50 V C.A./ 120 V C.C.
même sans piles,
– contrôle automatique des
piles,
– utilisation d’une seule main
pour les tests de prises de
courant par enclenchement
des pointes de test,
– test de phase (uniquement
Combi Check 1.2),)
– affichage visuel et signal
acoustique (uniquement
Combi Check 1.2),
– éclairage débrayable des
pointes de test (unique-
ment Combi Check 1.2).
Description de l’appareil
Mode d’emploi
F
15
All manuals and user guides at all-guides.com