Stellar Lighting MK-C6W2 User manual

www.stellarlighting.co.uk
email: [email protected]
1
MK-C6W2 light engine with fibre optic fibre bundle
User manual
Features:
•Complete star kit for small-scale
projects with light engine, remote
controller, 200 fibre bundle
•RGB light engine
•Touch remote with colour wheel
•Small size
Technical specification
Light engine model
MK-C6W2 RGB K
Programmes
11 programs, brightness (static mode) speed
(dynamic mode), on/off
Remote controller
Yes, RF
Light source type
RGB LED chip
CRI (Ra>):
70
IP rating
IP20
Light colour mode
RGB
Working voltage
DC12V
Rated power
6 W (Red: 2W, Green: 2W, Blue: 2W)
Material of housing
Aluminium
Light engine dimensions
135 mm (L) x 36 mm (W) x 36 mm (H)
Net weight
0.3 kg
Remote control dimensions
113.5 mm x 55.5 mm x 22.5 mm
Fibre optic port diameter
10-14 mm
Fibre optic bundle:
200 fibres: 160 x 0.75 mm, 40 x 1.0 mm at 2 m
length
Lifetime
50,000 hours
Warranty
2 years
Package dimensions (excluding fibre optic bundle)
200 mm (L)x 170 mm (W) x 90 mm (H)
Weight with packaging
0.7 kg

www.stellarlighting.co.uk
email: [email protected]
2
MK-C6W2 light engine with fibre optic fibre bundle
User manual
Safety notices
Electrical work safety advice and tips
●Make sure the input voltage is correct.
●Avoid placing the light engine in the rain or in moist areas. Please ensure that the light engine has
sufficient ventilation and is not placed in a completely sealed area.
●Do not open the LED light engine for inspection or re-wire the electronic circuits if you are not a
professional. Opening the light engine might void yourwarranty.
●Avoid any debris on top or around the light engine as it can cause poor heat dissipation.
●Avoid using the device above 40 C temperature.
DIY tips and safety advice
●This task will involve working at height. A safe system of work should be established and maintained, in
order to prevent injury.
●Consider your safety! Think about the potential risks and dangers of the work and the steps you should
take to avoid them.
●Personal protective equipment. Make sure that you are equipped with suitable and sufficient personal
protectiveequipment.Thiscouldincludeeye protection,facemask,protective overalls,safety footwear
and gloves.
●Ensure that the work area is sufficiently illuminated.
●Check that the tools you will be working with are in a good operating condition. For the installation,
you will need a cordless drill, epoxy glue, side cutters or scissors and drill bits.

www.stellarlighting.co.uk
email: [email protected]
3
MK-C6W2 light engine with fibre optic fibre bundle
User manual
Light engine and remote controller dimensions
Connection method between optical fibres and the light engine
Your fibre optic bundle will come with the
connector fittings ready to connect to the
light engine. However, if you need to adjust
your bundl
follow the steps below.
1. Align all the optical fibre ends and fasten with tapes which can resist temperature over 130℃
2. Pass the fibres through the connector and fasten the rotary tensioner until the fibres are tightened.
3. Cut the fibre bundle to a flat surface with a heat-knife or blade.

www.stellarlighting.co.uk
email: [email protected]
4
MK-C6W2 light engine with fibre optic fibre bundle
User manual
4. Make sure that the optical fibre bundle head is smooth and clean to ensure even light distribution.
5. he connector. Fasten the bundle with
the screw on the top of the .
Programming the light engine
Remote control operation
The remote controller works with 3 x AAA batteries. Batteries are not included.
Remote control programs
NO.
MODE
REMARK
NO.
mode
remark
1
Seven colourfade in and out
speed adjusted
5
Static red
bright adjusted
2
RGB fade in and out
6
Static green
3
Seven colour jump
7
Static blue
4
RGB jump
8
Static yellow
9
Static purple
10
Static cyan
11
Static white

www.stellarlighting.co.uk
email: [email protected]
5
MK-C6W2 light engine with fibre optic fibre bundle
User manual
Pairing the remote controller
Pairing
the light engine. However, in some cases the remote controller can unpair from the light engine. In these
scenarios, follow these steps:
Press th - e light will blink 3
times to indicate that the remote control is paired.
Unpairing
Press the + button once within 3 seconds of switching the light engine on. The light will blink 6
times if unpairing was successful.
Troubleshooting for remote controller connection issues:
•
•Check if the battery is operational in the remote controller: Press a button on the remoteand the
the remote or the battery needs replacing.
•indicator light on the back of the
light engine flashes up, when a button is pressed on the remote. If the indicator light is not flashing up,
the remote controller might be unpaired from the light engine. To pair the devices, press the
- tton once, within 3 seconds of switching the light engine on. The light will blink 3
times to indicate that the remote control is paired.
•controller, restart the device and test again.
•