Stentofon Vingtor Turbine Compact IP TCIS Series Installation instructions manual

Mounting Guide
TCIS Turbine Compact IP Stations
1 Turbine Compact IP Stations
This document describes the dimensions, mounting procedure, and connections of the STENTOFON Turbine
Compact IP Stations. The Turbine Compact IP product range comprises the following stations & accessories:
ITEM NUMBER TYPE ITEM NAME
1008111010/1028111010 TCIS-1/TCIS-1-V Turbine Compact IP Standard-1
1008111020 TCIS-2 Turbine Compact IP Standard-2
1008111030 TCIS-3 Turbine Compact IP Standard-3
1008111040 TCIS-4 Turbine Compact IP Standard-4
1008111050 TCIS-5 Turbine Compact IP Standard-5
1008111060 TCIS-6 Turbine Compact IP Standard-6
1008140010 TA-1 Turbine On-Wall Back Box
1008140020 TA-2 Turbine Flush Mount 2-Gang Double-Depth Back Box
1008140050 TA-5 Turbine Bracket for Flush Mount Back Box
1.1 TCIS Compact Station Dimensions
96 mm
156 mm
52 mm 20.5 mm
3.78”
6.14”
0.81”
2.05”
180 mm
120 mm
4.72”
7.09”
TCIS-1/TCIS-1-V TCIS-2 TCIS-3 TCIS-4 TCIS-5 TCIS-6

2 On-Wall Surface Mounting
2.1 On-Wall Surface Mount Back Box - TA-1
2.2 On-Wall Surface Mounting Procedure
LUse the grommets and M20 cable
gland provided for the cable holes
on the back box
1. Mount the back box onto the wall
2. Fit the gasket onto the back box with the ridged side facing down
–Plug the Ethernet cable into the RJ-45 port on the station
3. Mount the Turbine station onto the back box with the M5 fasteners provided
76 mm
150 mm
D6.5 mm
25 mm
120 mm
Mounting holes are to be drilled
as shown.
Max. recommended screw
diameter: ISO M6 or ANSI 1/4".
Screw length must be greater
than 25 mm or 1".
A4 stainless steel socket head
screws/bolts are recommended.
Max. recommended screw
head diameter: 9.5 mm or 3/8".
3”
5.90”
4.72”
1”
0.25”
D
Mounting Hole
Mounting Hole Mounting Hole
Mounting Hole
Optional nylon washers for extra
protection against corrosive effects
between surfaces are provided.
They should be placed at the bottom
of the mounting holes.
Grommets and an M20 cable gland
are provided.
cable holes
M20 M16
Surface Mount Back Box
Gasket
Turbine Station
1
2
3

3 Flush Mounting
3.1 Flush Mount 2-Gang Double-Depth Back Box - TA-2
LIt is recommended to utilize back boxes with weep holes at the bottom
3.2 Flush Mount Bracket - TA-5
LThe TA-5 Bracket is mandatory for flush mounting.
96 mm / 3.78?
48 mm
25 mm
23 mm
89 mm / 3.50?
89 mm / 3.50?
96 mm / 3.78?
46 mm
SIDE
SIDE
22 mm
1.81? 0.98?
0.90?
0.87?
1.89?
83 mm
87 mm
46 mm
50 mm
4 mm
4 mm
74 mm
91 mm
Fits US 2-GANG electrical boxes.
Recommended screw diameter: up to M4 (5/32")
Use screw recommended by back box manufacurer.
CUTOUT
0.16”
1.81”
0.16”
3.58”
1.97”
3.42”
3.27” 2.91”

STENTOFON and VINGTOR products are developed and marketed by Zenitel Norway AS. The company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001:2008. Zenitel
Norway AS reserves the right to modify designs and alter specifications without prior notice, in pursuance of a policy of continuous improvement. © 2012 Zenitel Norway AS.
DOC NO.
3.3 Flush Mounting Procedure
1. Mount the 2-gang back box into the wall
2. Mount the bracket onto the back box
3. Fit the gasket onto the bracket with the ridged side
facing down
–Plug the Ethernet cable into the RJ-45 port on the station
4. Mount the Turbine station onto the bracket with the M5
fasteners provided
4 Connections
The Turbine Compact IP station has a RJ-45 PoE/LAN port, and 6-pin & 10-pin external connectors.
Ethernet /
Power
10/100 Mbps Ethernet RJ-45 port for LAN
(uplink) connection. Supports PoE (802.3af).
Draws power from either spare line or signal line.
Secondary
Power
24 VDC (16 – 48 V) secondary power is provided
from an external adapter.
Relays There is one Double Throw relay contact with
60W switching power. COM, NO, NC contacts
are provided. Max: 250VAC/220VDC, 2A, 60W.
Input/Output 6 I/Os are available. Each I/O can be configured
as either input, output, or LED driver.
Audio Line Out A balanced 600 ohm audio line out with
induction loop signal
LUse cables crimped with ferrules for terminal block connectors
• When the Turbine Station is connected to the network, its IP address is automatically
obtained from a DHCP server or an IP address in the range 169.254.x.x will be assigned.
• To make the station speak its IP address, press the call button on the station.
Bracket
Gasket
Turbine Station
2
3
4
Flush Mount 2-Gang Back Box
1
1
5
4
3
2
1
6
10
5
4
3
2
9
8
7
RJ-45
PoE
port
24 VDC for external secondary power
if PoE is not used. Pin 1 is positive.
- 5.3V (LED driver)
- GND
- Input/Output 5
- COM relay
- NC relay
- NO relay
- Input/Output 1
- Input/Output 2
- Input/Output 3
- Input/Output 6
- 600 ohm balanced line out +
- 600 ohm balanced line out -
- Input/Output 4
Ethernet Connection
10.9.2012
A100K11254 [e-mail]
[email protected]