Steren ANT-UHF 16 User manual

ENGLISH
ENGLISH-02
IMPORTANT
Before installing the ANT-UHF 16 antenna, please read this
instruction manual in order to avoid malfunctions or poor use of
this device. Please keep this manual for future reference.
Do not install this antenna near high-tension cables or transformers.
Do not place the antenna’s cable near electronic devices.
Do not set the mast in metallic structures.
Use plastic isolating ties in order to hold the cables.
FEATURES
16 element aerial antenna.
10dB gain.
Manufactured in aluminum.
CONTAINED WITHIN
1 Cap for “F” connector.
1 Central mast.
1 Impedance adaptor.
4 Buttery nuts.
3 Separators.
2 Complement pieces for antenna.
2 Holding pieces for antenna.
•
•
•
•
•
•
•

ENGLISH
ENGLISH-03
HOW TO ASSEMBLE YOUR NEW ANTENNA
We suggest you obtain help from a second person in order to
assemble and install your new antenna.
1. Place the impedance adaptor in the central mast. Make sure to place
the screw in the hole showed in g. 1. On the other side, place the
separator on the screw and use the buttery nut in order to tighten the
impedance adaptor.
2. In one end of the central mast, insert the “A” piece and on the other
endthe “B” piece. Place the holding screw in the hole and tighten it
using the buttery nut.
3. Place pieces “C” and “D” on either side of the antenna holding piece
and tighten them with the buttery nuts until they are rmly in place.
4. Insert the cap in the TV’s coaxial cable and connect this cable to the
“F” connector on the impedance adaptor. Afterwards, place the cap so
that it covers the antennas connector.
5. Set the antenna rmly on the mast by tightening the buttery nuts.
(See g. 4)
6. Direct the antenna to a clear area and towards the transmission
tower.
This package does not include a mast.

ENGLISH
ENGLISH-04
g. 1
B
A g. 2
g. 3

ENGLISH
ENGLISH-05
SPECIFICATIONS
Channels: 2-13 (VHF) 14-83 (UHF)
Elements: 16
Gain: 10dB
Cable Connections: 75Ohms
Frequency: 54MHz – 890MHz
Frequency Band: VHF-UHF
Product desing and specications are subject to change without
previous notice

WARRANTY
This Steren product is warranted under normal usage against defects in workmanship and
materials to the original purchaser for one year from the date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase ticket, product
box or package, and product, must be presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accessories to customer, as well as
warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries,
failure to follow enclosed instructions, improper repair by unauthorized personnel, improper
safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
Product: 16 Elements VHF-UHF aerial antenna
Part number: ANT-UHF 16
Brand: Steren

RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your nearest dealer. If
you are in Mexico, please give a call to our Call Center.
Call Center
01 800 500 9000

IMPORTANTE
Antes de instalar la antena aérea ANT-UHF 16 lea este instructivo
para evitar mal funcionamiento. Guárdelo para futuras referencias.
No instale la antena cerca de cables de alta tensión o
transformadores.
No pasar el cable de la antena cerca de aparatos eléctricos.
No je el mástil a estructuras metálicas.
Utilice cinchos aislantes de plástico para sujetar el cable.
CARACTERISTICAS
Antena aérea de 16 elementos.
Ganancia de 10dB.
Fabricado en aluminio.
CONTENIDO
1 Capuchón para conector F.
1 Tubo central.
1 Adaptador de impedancia.
4 Mariposas de ajuste.
3 Empaques.
2 Piezas complemento de antena.
2 Piezas de sujeción para antena.
•
•
•
•
•
•
•
ESPAÑOL-02
ESPAÑOL
Antes de utilizar su nuevo Kit C

COMO ARMAR SU NUEVA ANTENA
Para armar la antena apóyese de otra persona para sujetarlo
rmemente.
1.- Coloque el adaptador de impedancia, insertando el tornillo en el
oricio del tubo central mostrado en la g. 1 y en el extremo contrario
coloque la mariposa de ajuste, coloque el empaque y gire la mariposa
hacia la derecha hasta que ajuste rmemente (ver g.1)
2.-Inserte en un extremo del tubo central la pieza A y en el extremo
contrario la pieza B coloque el tornillo de sujeción en el oricio y ajuste
con la mariposa (ver g. 2), Coloque las piezas C y D en los extremos
de la pieza de sujeción para antena y ajuste con la mariposa hasta que
queden rmemente sujetos (ver g.3)
3.-Inserte el capuchón en el cable coaxial del televisor y conecte el
cable a la entrada tipo F del adaptador de impedancia y coloque el
capuchón de tal forma que se cubra el conector de la antena.
4.-Sujete la antena rmemente al mástil ajustando con las mariposas de
sujeción.
No incluye mástil.
5.-Oriente la antena a un área despejada que se encuentre en dirección
a la torre trasmisora.
ESPAÑOL-03
ESPAÑOL