STIEBEL ELTRON CK 20 S Specification sheet

BEDIENUNG UND INSTALLATION
OPERATION AND INSTALLATION
UTILISATION ET INSTALLATION
BEDIENING EN INSTALLATIE
OBSLUHA A INSTALACE
HASZNÁLATI ÉS TELEPÍTÉSI ÚTMUTATÓ
Schnellheizer | Rapid heater | Radiateur à chauffage rapide | Snelverwarmers |
Rychloohřívač | Gyorsfűtő
» CK 20 S
» CKZ 20 S
» CKR 20 S
» CKT 20 S

14 | CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S www.stiebel-eltron.com
CONTENTS | SPECIAL INFORMATION
SPECIAL INFORMATION
- Keep children under the age of3 away from
the appliance if constant supervision cannot be
guaranteed.
- Children from the age of 3 to 7 may switch the
appliance on and off, provided they are super-
vised or have been instructed in the safe oper-
ation of the appliance and understand any risks
that may result. This is subject to the appliance
having been installed as described.
Children from the age of 3 to 7 must not plug
the power cable into its socket nor regulate the
appliance.
- The appliance may be used by children aged8
and older and persons with reduced physical,
sensory or mental capabilities or a lack of expe-
rience and know-how, provided that they are su-
pervised or they have been instructed on how to
use the appliance safely and have understood the
resulting risks.
- Children must never play with the appliance. Chil-
dren must never clean the appliance or perform
user maintenance unless they are supervised.
- The appliance could continue to heat the room
unchecked if it is operated on a time switch. En-
sure constant supervision if the appliance is used
in a small room and the persons within that room
cannot leave the room on their own.
- Parts of the appliance can get very hot and may
cause burns.
Particular caution is advised when children or
vulnerable persons are present.
- Never cover the appliance.
- Never install the appliance directly below a wall
socket.
SPECIAL INFORMATION
OPERATION
1. General information ��������������������������������������� 15
1.1 Safety instructions���������������������������������������������� 15
1.2 Other symbols in this documentation ���������������������� 15
1.3 Information on the appliance �������������������������������� 15
1.4 Units of measurement ����������������������������������������� 15
2. Safety�������������������������������������������������������� 15
2.1 Intended use����������������������������������������������������� 15
2.2 General safety instructions ����������������������������������� 16
2.3 Test symbols ����������������������������������������������������� 16
3. Appliance description ������������������������������������� 16
4. Operation CK 20 S ������������������������������������������ 16
4.1 Start heating����������������������������������������������������� 16
4.2 Control with external room temperature controller ���� 17
4.3 Stopping heating / frost protection ������������������������� 17
4.4 Decommissioning����������������������������������������������� 17
5. Operation CKZ 20 S����������������������������������������� 17
5.1 Start heating����������������������������������������������������� 17
5.2 Stopping heating / frost protection ������������������������� 17
5.3 Decommissioning����������������������������������������������� 17
6. Operation CKR 20 S ���������������������������������������� 17
6.1 Start heating����������������������������������������������������� 17
6.2 Control with external room temperature controller ���� 18
6.3 Stopping heating / frost protection ������������������������� 18
6.4 Decommissioning����������������������������������������������� 18
7. Operation CKT 20 S����������������������������������������� 18
7.1 Start heating����������������������������������������������������� 18
7.2 Adjusting the time switch������������������������������������� 18
7.3 Stopping heating / frost protection ������������������������� 18
7.4 Decommissioning����������������������������������������������� 18
8. Cleaning, care and maintenance ������������������������� 18
9. Storage ������������������������������������������������������ 18
10. Troubleshooting �������������������������������������������� 18
INSTALLATION
11. Safety�������������������������������������������������������� 19
11.1 General safety instructions ����������������������������������� 19
11.2 Instructions, standards and regulations ������������������� 19
12. Appliance description ������������������������������������� 19
12.1 Standard delivery����������������������������������������������� 19
13. Preparations������������������������������������������������ 19
13.1 Minimum clearances������������������������������������������� 19
14. Installation�������������������������������������������������� 19
15. Power supply����������������������������������������������� 19
16. Appliance handover���������������������������������������� 20
17. Troubleshooting �������������������������������������������� 20
18. Specification ������������������������������������������������ 20
18.1 Dimensions and connections��������������������������������� 20
18.2 Wiring diagram CK 20 S ��������������������������������������� 21
18.3 Wiring diagram CKZ 20 S ������������������������������������� 21
18.4 Wiring diagram CKR 20 S ������������������������������������� 22
18.5 Wiring diagram CKT 20 S�������������������������������������� 22
18.6 Data table �������������������������������������������������������� 23
GUARANTEE
ENVIRONMENT AND RECYCLING

OPERATION
General information
www.stiebel-eltron.com CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S | 15
ENGLISH
- Install the appliance in such a way that the con-
trol equipment cannot be touched by a person in
the bath or shower.
- In the case of a permanent connection, the ap-
pliance must be able to be separated from the
power supply by an isolator that disconnects all
poles with at least 3 mm contact separation.
- In the event of damage to the power cable this
must always be replaced by a qualified contractor
authorised by the manufacturer, using original
spare parts.
- Secure the appliance as described in chapter "In-
stallation/ Installation".
OPERATION
1. General information
The chapters "Special Information" and "Operation" are intended
for both the user and qualified contractors.
The chapter "Installation" is intended for qualified contractors.
Note Read these instructions carefully before using the appli-
ance and retain them for future reference.
Pass on the instructions to a new user if required.
1.1 Safety instructions
1.1.1 Structure of safety instructions
!KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
 Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol Type of risk
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD Meaning
DANGER Failure to observe this information will result in serious
injury or death.
WARNING Failure to observe this information may result in serious
injury or death.
CAUTION Failure to observe this information may result in non-seri-
ous or minor injury.
1.2 Other symbols in this documentation
Note General information is identified by the adjacent symbol.
 Read these texts carefully.
Symbol Meaning
Material losses
(appliance damage, consequential losses and environmen-
tal pollution)
Appliance disposal
 This symbol indicates that you have to do something. The ac-
tion you need to take is described step by step.
1.3 Information on the appliance
Symbol Meaning
Never cover the appliance
1.4 Units of measurement
Note All measurements are given in mm unless stated oth-
erwise.
2. Safety
Operate the appliance only when fully installed and with all safety
equipment fitted.
2.1 Intended use
This appliance is intended for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-do-
mestic environment, e.g. in a small business, as long as it is used
in the same way.
Any other use beyond that described shall be deemed inappropri-
ate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
!
!

OPERATION
Appliance description
16 | CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S www.stiebel-eltron.com
2.2 General safety instructions
!WARNING Injury
-Keep children under the age of3 away from the
appliance if constant supervision cannot be guar-
anteed.
-Children from the age of 3 to 7 may switch the ap-
pliance on and off, provided they are supervised
or have been instructed in the safe operation of
the appliance and understand any risks that may
result. This is subject to the appliance having been
installed as described.
Children from the age of 3 to 7 must not plug the
power cable into its socket nor regulate the appli-
ance.
-The appliance may be used by children aged8 and
older and persons with reduced physical, sensory
or mental capabilities or a lack of experience and
know-how, provided that they are supervised or
they have been instructed on how to use the appli-
ance safely and have understood the resulting risks.
-Children must never play with the appliance. Chil-
dren must never clean the appliance or perform
user maintenance unless they are supervised.
WARNING Burns Never operate this appliance...
-if the minimum clearances to adjacent object sur-
faces are not maintained, for example to furniture,
net curtains, curtains, textiles or other flammable
materials (for minimum clearances, see “Installation
/ Preparations”).
-in rooms where the appliance is at risk of fire or
explosion as a result of chemicals, dust, gases or
vapours.
-in the direct proximity of pipes or receptacles that
carry or contain flammable or explosive materials.
-if work such as laying cables, grinding or sealing is
carried out in the installation room.
-if sprays, floor polish or similar products containing
naphtha are used. Ventilate the room sufficiently
before heating.
-if an appliance component is damaged, the appli-
ance has fallen over or already has a fault.
WARNING Burns Never place any flammable, combustible or insulating
objects or materials, such as laundry, blankets, maga-
zines, containers with floor polish or naphtha, spray cans
or similar on the appliance or in direct proximity to it.
WARNING Burns Ensure that no foreign bodies enter the ventilation and
extract air apertures. This could result in electric shock
or fire or in damage to the appliance.
WARNING Burns To prevent fires ensure that the air inlets and outlets are
never blocked. Never position the appliance on soft sur-
faces, such as a bed, as this could result in the apertures
becoming blocked.
!CAUTION Injury
The appliance could continue to heat the room unchecked
if it is operated on a time switch. Ensure constant su-
pervision if the appliance is used in a small room and
the persons within that room cannot leave the room on
their own.
CAUTION Burns Parts of the appliance can get very hot and may cause
burns. Particular caution is advised when children or
vulnerable persons are present.
!Material losses
- Never cover the appliance.
- Never step on the appliance.
- Never operate the appliance in the open air.
2.3 Test symbols
See type plate on the appliance.
3. Appliance description
This appliance is wall mounted and is particularly suitable for work
rooms, kitchens, bathrooms, wash rooms and similar.
The external casing of the appliance is made from stove enamelled
sheet steel. The sides are made from plastic. The controls are
located on the r.h. side panel.
The quiet fan draws in the ambient air that is heated by a bare wire
heater element. The air then exits evenly through the hot air chan-
nel and the air outlet grille set into the bottom of the appliance.
The appliance heats up the ambient air inside the room and main-
tains it at the selected temperature.
After mounting the appliance on the wall and making the elec-
trical connection using a mains plug, the appliance is ready for
operation.
4. Operation CK 20 S
1
26�07�31�0211
1 Temperature selector
4.1 Start heating
The temperature is variably adjustable. The appliance switches
off as soon as the selected room temperature has been reached.
 Turn the temperature selector clockwise to the required
setting.

OPERATION
Operation CKZ 20 S
www.stiebel-eltron.com CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S | 17
ENGLISH
4.2 Control with external room temperature
controller
In rooms larger than 20m2 you can operate the appliance with a
conventional external room temperature controller.
 To do so, turn the temperature selector fully clockwise.
4.3 Stopping heating / frost protection
 Turn the temperature selector fully anti-clockwise.
This position ensures frost protection. The heating system starts
automatically if the room temperature drops below the frost pro-
tection temperature.
4.4 Decommissioning
 Pull the plug from the power socket.
5. Operation CKZ 20 S
1
23
5
4
26�07�31�0212
1 Temperature selector
2 Rocker switch position (operation with the time switch)
3 Rocker switch position (standard operation)
4 Time switch
5 Marker arrow
5.1 Start heating
 Use the rocker switch to select one of the following operating
modes:
- Standard operation
- Operation with the time switch
Standard operation
The temperature is variably adjustable. The appliance switches
off as soon as the selected room temperature has been reached.
 Turn the temperature selector clockwise to the required
setting.
Operation with the time switch
The 24-hour time switch has 96 time segments. Every hour is di-
vided into 4 time segments of 15 minutes. The time switch has to
be reset when commissioning the appliance and after any power
interruption. To do this, turn the time switch clockwise until the
marker arrow points to the current time.
To select the required heating time, proceed as follows:
Press down the time segments around the circumference. Red
markings will become visible, indicating the preselected heating
time at which the appliance automatically starts to heat. If the
required room temperature has been reached during the heat-up
time, the appliance switches off. It starts again if there is a further
heat demand and will continue doing so until the selected heating
time has elapsed. This process is repeated daily. The heating time
can be adjusted at any time if required by pressing time segments
up or down.
5.2 Stopping heating / frost protection
 Turn the temperature selector fully anti-clockwise.
In this setting, frost protection is only ensured if the rocker switch
is positioned for "Standard operation". The heating system starts
automatically if the room temperature drops below the frost pro-
tection temperature.
5.3 Decommissioning
 Pull the plug from the power socket.
6. Operation CKR 20 S
23
1
26�07�31�0213
1 Temperature selector
2 Rocker switch stage (base heating stage)
3 Rocker switch stage (quick heating stage)
6.1 Start heating
 Turn the temperature selector clockwise to the required
setting.
The temperature is variably adjustable. The appliance switches
off as soon as the selected room temperature has been reached.
You can use the rocker switch to choose between the following
two outputs with matched fan motor speed:

OPERATION
Operation CKT 20 S
18 | CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S www.stiebel-eltron.com
Base heating stage
Set the rocker switch to "I". Provided that the appliance has been
switched on via the temperature selector, it will heat with an
output of 1000W at the slow fan stage.
Note Never operate the appliance at standard heating stageI,
if the room where the appliance has been installed has
cooled down severely.
 If the room has cooled down severely, switch the
appliance to rapid heating stageII in order to ensure
normal appliance operation.
Quick heating stage
Set the rocker switch to "II". Provided that the appliance has been
switched on via the temperature selector, it will heat with an
output of 2000W at the quick fan stage.
Select the powerful quick heating stage if you need to heat up a
cold room rapidly to the selected temperature. Afterwards, set the
rocker switch back to stage "I".
Once the preselected room temperature has been reached, the
appliance switches off. The appliance then starts and stops heating
as necessary to keep the room temperature constant.
6.2 Control with external room temperature
controller
In rooms larger than 20m2 you can operate the appliance with a
conventional external room temperature controller.
 To do so, turn the temperature selector fully clockwise.
6.3 Stopping heating / frost protection
 Turn the temperature selector fully anti-clockwise and select
quick heating stage "II" on the rocker switch.
This position ensures frost protection. The heating system starts
automatically if the room temperature drops below the frost pro-
tection temperature.
6.4 Decommissioning
 Pull the plug from the power socket.
7. Operation CKT 20 S
1
2
26�07�31�0214
1 Temperature selector
2 Time switch
7.1 Start heating
The temperature is variably adjustable. The appliance switches
off as soon as the selected room temperature has been reached.
 Turn the temperature selector clockwise to the required
setting.
7.2 Adjusting the time switch
With the time switch, the appliance heats with full output and
without temperature control.
 Turn the time switch selector clockwise to set any number of
minutes to count down, from 0 - 60 minutes.
7.3 Stopping heating / frost protection
 Turn the temperature selector fully anti-clockwise and ensure
that the time switch is set to "0".
This position ensures frost protection. The heating system starts
automatically if the room temperature drops below the frost pro-
tection temperature.
7.4 Decommissioning
 Pull the plug from the power socket.
8. Cleaning, care and maintenance
The appliance contains no user serviceable parts.
Clean the appliance when cold with ordinary cleaning products.
Avoid abrasive or corrosive cleaning products.
If a pale brownish discolouration appears on the appliance casing,
wipe this off as soon as possible with a damp cloth.
!Material losses
Never spray cleaning spray into the air slot.
9. Storage
 When not in use, keep the appliance in a dry place.
10. Troubleshooting
If the appliance does not heat, check the temperature set at the
appliance and the MCB/fuse in your fuse box.
The appliance has a safety temperature controller that shuts the
appliance down if it overheats. After the cause has been removed
(for example air outlet or inlet apertures covered) and the appli-
ance has cooled down for a few minutes, operation starts again.
If you cannot remedy the fault, notify your heating contractor. To
facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000).

INSTALLATION
Safety
www.stiebel-eltron.com CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S | 19
ENGLISH
INSTALLATION
11. Safety
Only a qualified contractor should carry out installation, commis-
sioning, maintenance and repair of the appliance.
11.1 General safety instructions
We guarantee trouble-free function and operational reliability only
if original accessories and spare parts intended for the appliance
are used.
11.2 Instructions, standards and regulations
Note Observe all applicable national and regional regulations
and instructions.
12. Appliance description
This appliance is a wall mounted electric direct heater. This ap-
pliance is particularly suitable for heating rooms, such as work
rooms, kitchens, bathrooms, wash rooms etc.
12.1 Standard delivery
The following are delivered with the appliance:
- Wall mounting bracket
- Fixing bracket
13. Preparations
13.1 Minimum clearances
≥10
≥100≥100
≥500
≥100 ≥100
D0000018481
14. Installation
WARNING Electrocution -If installing the appliance in rooms with a bath
and/or shower, take the relevant safety zone into
account in accordance with the information on the
appliance type plate.
-Install the appliance in such a way that control
equipment cannot be touched by a person in the
bath or shower.
WARNING Burns -Only fit the appliance to a vertical wall that is tem-
perature-resistant to at least 90 °C.
-Maintain minimum clearances to adjacent surfaces.
-Never install the appliance directly below a wall
socket.
 Check the hole distances for the wall mounting bracket in the
dimensioned drawing.
 Secure the wall mounting bracket with suitable fixing mate-
rials. The horizontal and vertical slots in the wall mounting
bracket enable alignment if drilled holes are not completely
accurate.
 Position the appliance against the wall so that the two pro-
trusions in the top of the back panel grip into the slots in the
wall mounting bracket.
 Secure the appliance with the mounting bracket and one
screw to prevent unintentional unhooking. Hook the mount-
ing bracket into the back panel from the lower rear.
15. Power supply
WARNING Electrocution Carry out all electrical connection and installation work
in accordance with relevant regulations.
!Material losses
Observe the type plate. The specified voltage must match
the mains voltage.
- The cable must not touch the appliance.
- When connecting the appliance via a standard socket, ensure
that this is easily accessible once the appliance has been
installed.
- Never install the appliance directly below a wall socket.
- If a permanent connection is required, trim the cable (cut
off the plug) so that it runs directly to the appliance junction
box.
- In the case of a permanent connection, the appliance must
be able to be separated from the power supply by an iso-
lator that disconnects all poles with at least 3 mm contact
separation.
- This appliance is unsuitable for fixed cables.

INSTALLATION
Appliance handover
20 | CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S www.stiebel-eltron.com
16. Appliance handover
Explain the functions of the appliance to the user. Draw special
attention to the safety instructions. Hand over the operating and
installation instructions to the user.
17. Troubleshooting
The power cable must only be replaced by a qualified contractor
using original spare parts supplied by us.
18. Specification
18.1 Dimensions and connections
i13
i32
b01
335 123
10
200
460
365
D0000018442
b01 Cable entries
i13 Wall mounting bracket
i32 fixing

INSTALLATION
Specication
www.stiebel-eltron.com CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S | 21
ENGLISH
18.2 Wiring diagram CK 20 S
N1
R1
F1
>80 °C ±5 K
>80 °C ±5 K
F1
X1
X2
1
PE L N
2
M1
M
1 ~
R2
A1
26�07�31�0216
A1 Electric heater element assembly
F1 Overheating protection
M1 Fan
N1 Temperature controller
R1 Heating resistor
R2 Heating resistor
X1 Socket terminal
X2 Plug-in connection
18.3 Wiring diagram CKZ 20 S
26�07�31�0217
A1 Electric heater element assembly
F1 Overheating protection
M1 Fan
N1 Temperature controller
R1 Heating resistor
R2 Heating resistor
T1 Time switch
W1 Rocker switch
X1 Socket terminal
X2 Plug-in connection

INSTALLATION
Specication
22 | CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S www.stiebel-eltron.com
18.4 Wiring diagram CKR 20 S
6(1a)
5(1)
3(2a) 1(2b)
2(2)
26�07�31�0046
A1 Electric heater element assembly
F1 Overheating protection
M1 Fan
N1 Temperature controller
R1 Heating resistor
R2 Heating resistor
W1 Rocker switch
X1 Socket terminal
X2 Plug-in connection
18.5 Wiring diagram CKT 20 S
> 174°F ± 41°F
> 80°C ± 5K
ϑ
ϑ
> 174°F ± 41°F
> 80°C ± 5K
ϑ

1
324
6 5
12
N1 R1 R2
F1
F1
X1
X2
T1
M1
PE LN
A1
M
1~
26�07�31�0215
A1 Electric heater element assembly
F1 Overheating protection
M1 Fan
N1 Temperature controller
R1 Heating resistor
R2 Heating resistor
T1 60 minute time switch
X1 Socket terminal strip

www.stiebel-eltron.com CK 20 S | CKZ 20 S | CKR 20 S | CKT 20 S | 23
ENGLISH
INSTALLATION | GUARANTEE | ENVIRONMENT AND RECYCLING
Specication
18.6 Data table
CK 20 S CKZ 20 S CKR 20 S CKT 20 S
Part number 071793 071795 072633 230344
Electrical data
Connected load W2000 2000 2000 2000
Phases 1/N/PE 1/N/PE 1/N/PE 1/N/PE
Rated voltage V230 230 230 230
Frequency Hz 50 50 50 50
Dimensions
Height mm 460 460 460 460
Width mm 335 335 335 335
Depth mm 123 123 123 123
Weights
Weight kg 4.4 4.4 4.4 4.4
Versions
Version 24 h time switch 60-minute short-time
timer
Frost protection setting °C 7777
IP rating IP13B IP13B IP13B IP13B
Protection class IIII
Colour Alpine white Alpine white Alpine white Alpine white
Values
Output stages 1.0 / 2.0 kW
Setting range °C 5-30 5-30 5-30 5-30
Operating noise dB(A) 53 53 42/51 53
GUARANTEE
ENVIRONMENT AND RECYCLING
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.



Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.de
Verkauf Tel. [phone] | Fax [phone] | [email protected]
Kundendienst Tel. [phone] | Fax [phone] | [email protected]
Ersatzteilverkauf Tel. [phone] | Fax [phone] | [email protected]
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van ver
g
issin
g
en en technische wi
j
zi
g
in
g
en! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian
y
techniczne i
ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések
j
o
g
át
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Ch
y
b
y
a
technické zmeny sú vyhradené! Stand 9147
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne VIC 3207
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Gewerbegebiet Neubau-Nord
Margaritenstraße 4 A | 4063 Hörsching
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. [phone]
[email protected]
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. [phone] | Fax [phone]
[email protected]
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ru
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. [phone] | Fax [phone]
[e-mail]
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. [phone] | Fax [phone]
[email protected]
www.stiebel-eltron-usa.com
A 128685-39874-9233
4<AMHCMM=cigifd>