Stinger CS58 User manual
• Operation
• Safety
®
www.stingerworld.com
!
• Maintenance
• Warranty
CS58 CAP STAPLER OWNER’S MANUAL
REV 06/15
PLEASE READ!
This manual contains important information about product safety.
www.stingerworld.com
CS58 Cap Stapler
Congratulations on purchasing the STINGER CS58 Cap Stapler. You have selected a brand and a
tool that you can count on to deliver best practice installation, and perform job after job.
Please take the time to read and understand the information contained in this Owner’s Manual
before operating or maintaining the STINGER CS58 Cap Stapler.
The CS58 is intended for securing housewrap and roofing felt only.
Improper use of the CS58 could result in serious injury or even death. Most accidents occur
because of the failure to observe basic safety rules and precautions, which are outlined in the
“Important Information” section of this manual.
This Owner’s Manual should be available to anyone who plans to operate the CS58.
WELCOME'TO'STINGER'
i
www.stingerworld.com
CS58 Cap Stapler
• Important Information 1
• Tool Specifications 4
• Loading the Tool 5
• Operating the Tool 6
• STINGER CS58 Schematic 8
• STINGER CS58 Parts List 9
• Maintenance and Storage 10
• Warranty 11
• Troubleshooting 12
TABLE'OF'CONTENTS'
ii
www.stingerworld.com
CS58 Cap Stapler
IMPORTANT'INFORMATION' !
PERSONAL SAFETY ITEMS
• Do not use tool prior to reading the Owner’s Manual.
• Always wear eye protection that conforms to ANSI requirements (Z87.1) and
provides protection against flying particles both from the front and side. Eye
protection should be worn by the operator and by others in the work area. Eye
protection is required to protect against flying fasteners and debris that could
possibly cause severe eye injury.
• The employer is responsible to enforce the use of eye protection equipment by the tool
operator and all other personnel in the work area.
• To prevent accidental injuries:
– Handle the tool with care
– Always assume that the tool contains fasteners
– Always disconnect the air hose from the STINGER CS58 when:
• loading staples and/or caps
• performing inspection, maintenance or repair
• clearing a staple or collated cap jam
• the tool is not in use
• leaving the work area
• moving the STINGER CS58 to another work location
• handing the STINGER CS58 to another person
• storing the tool
– Never point the tool toward yourself or anyone else
– Never engage in horseplay
– Never hold or carry the tool with a finger on the trigger
– Never place a hand or any other part of the body in the fastener discharge area of
the tool while the air supply is connected
1
www.stingerworld.com
CS58 Cap Stapler
IMPORTANT'INFORMATION'
AIR'SUPPLY'AND'CONNECTIONS'
'
! "#$%&'()%*($+',%-$./(+0$1%*&23-$##$1%+4-%+#%+%3&5$-%#&/-*$%6&-%074#%0&&(8%%9&%'&0%/#$%:&;($%.+#$#,%
*&2:/#<:($%.+#$#%&-%&=).$'%+#%+%3&5$-%#&/-*$%6&-%07$%0&&(%+#%07$%0&&(%2+)%$=3(&1$8%
! 9&%'&0%/#$%+4-%#/33()%3-$##/-$#%07+0%$=*$$1%>?%@AB8%
! 9&%'&0%$=*$$1%07$%-$*&22$'1$1%2+=42/2%&3$-+<'.%+4-%3-$##/-$%+#%0&&(%5$+-%54((%:$%.-$+0()%
4'*-$+#$18%%C7$%+4-%#/33()%2/#0%:$%*+3+:($%&6%2+4'0+4'4'.%07$%&3$-+<'.%+4-%3-$##/-$%&6%07$%0&&(8%%
@-$##/-$%1-&3#%4'%07$%+4-%#/33()%*+'%-$1/*$%07$%0&&(’#%1-4D4'.%3&5$-8%
! "#$%+%3-$##/-$%-$./(+0&-%+'1%.+/.$%0&%+((&5%D4#/+(%4'#3$*<&'%&6%07$%+4-%3-$##/-$%:$4'.%1$(4D$-$1%0&%07$%
0&&(8%
! "#$%+4-%7&#$#%07+0%7+D$%-+0$1%3-$##/-$#%&6%/3%0&%E?FG%&6%07$%2+=42/2%3-$##/-$%07+0%*+'%:$%.$'$-+0$1%
:)%07$%3&5$-%#&/-*$8%%C7$%#/33()%7&#$%#7&/(1%*&'0+4'%HI'.#%07+0%54((%3-&D41$%J/4*K%14#*&''$*<'.%6-&2%
07$%2+($%3(/.%&'%07$%0&&(8%
! "#$%J/4*K%*&''$*0%HI'.#%07+0%+((&5%07$%0&&(%0&%:$%/'7&&K$1%6-&2%07$%+4-%#/33()%J/4*K()%+'1%$+#4()8%
! 9&%'&0%/#$%HI'.#%07+0%54((%'&0%+((&5%07$%0&&(%0&%$=7+/#0%57$'%07$%+4-%#/33()%4#%14#*&''$*0$18%
2
www.stingerworld.com
CS58 Cap Stapler
IMPORTANT'INFORMATION'
OPERATION OF THE TOOL
• Never inspect, maintain, repair, adjust, clear a jam or store the tool with the air connected.
• Never use the tool in proximity of flammable gases or liquids, as some tools will create sparks
that can be an ignition source for a fire or explosion.
• Always inspect the safety device for damage and proper operation, prior to operation.
• Never assume the tool is empty of fasteners.
• Never point the tool toward yourself or any other persons.
• Never cycle the tool unless it is in contact with the work-piece.
• Never use the tool as a hammer or wedging device or drop to the floor from any height.
• Always remove your finger from the trigger when pausing from cycling.
• Never tamper with the safety device or use the tool if the safety device is not functioning
properly.
• Use only 5/8” STINGER StaplePac®cap fasteners with the STINGER CS58 Cap Stapler.
Never use any fasteners that are not specified for use in this tool. The CS58 holds 1 coil of
plastic caps (200 caps) and 2 strips of staples (100 staples each).
3
www.stingerworld.com
CS58 Cap Stapler
Operating pressure 90-95 psi
Weight 3.9 lb.
Nail capacity 200 staples (2-100 count strips)
Cap capacity 200 plastic collated caps (1 reel)
Air inlet ¼”
Fasteners STINGER StaplePac®(National Nail product number 0136360)
Consists of 20 strips of 5/8”20 gauge staples (100 staples per strip)
and 10 reels of 1”diameter plastic collated caps (200 caps per reel).
4
TOOL'SPECIFICATIONS'
www.stingerworld.com
CS58 Cap Stapler
LOADING'THE'TOOL'
USE 5/8
”
STINGER STAPLEPAC®CAP STAPLES ONLY
• Disconnect air.
• Open the magazine cover by pushing the green cover release
tab and lifting.
• Place cap reel in basket. Make sure the front end of the cap
coil is placed over the cap guide area of the basket. Insert
lead cap into the feed chute.
• Slide caps along the feed chute with fingers until they engage
the cap feeder. Pull the cap feeder back and release to
advance caps until the first cap is under the nose of the tool.
• Close the magazine cover.
• Depress the latch on the staple follower and pull back. Insert
two staple strips. Slide staple follower in and secure.
• Plug into air source. Tool is ready to use.
5
www.stingerworld.com
CS58 Cap Stapler
OPERATING'THE'TOOL'
1. Do not use tool prior to reading the Owner’s Manual.
2. Read warning label(s) on the tool.
3. Visually inspect the tool for worn or damaged parts.
4. Wear appropriate eye and ear protection.
5. Install a male pneumatic fitting into the end cap of the tool, ensuring that the fitting allows the
tool to exhaust any air in the tool when the air hose is disconnected.
6. Add 2 drops of non-detergent, 20-weight oil into the male fitting.
7. Connect the air hose using a quick connect fitting to the tool, and check the air pressure
reading on the regulator to ensure it does not exceed 95 PSI. Check the tool for any air
leaks.
8. Place the tool, empty of fasteners, in operating position on a scrap work piece. Fully depress
the safety and pull the trigger to verify that the tool cycles.
9. Disconnect the air hose from the tool when:
• Loading staples and/or caps
• Performing inspection, maintenance or repair
• Clearing a staple or collated cap jam
• The tool is not in use
• Leaving the work area
• Moving the tool to another work location
• Handing the STINGER CS58 to another person
• Storing the tool
10. Following recommended loading instructions, load the fasteners approved for use in the tool.
6
www.stingerworld.com
CS58 Cap Stapler
OPERATING'THE'TOOL'
11. Cycle the tool on a scrap work piece to evaluate the depth of penetration by the fastener into
the work piece.
12. To adjust the depth of penetration, regulate the air pressure at the regulator and/or
disconnect the air hose, adjust the depth control screw, connect the air hose and cycle the
tool on a scrap work piece to evaluate the adjustment.
13. Repeat Step 12 as needed to set the correct depth, using the minimum amount of air
pressure to drive the fastener.
7
www.stingerworld.com
CS58 Cap Stapler
STINGER'CS58'SCHEMATIC'
8
www.stingerworld.com
CS58 Cap Stapler
STINGER'CS58'PARTS'LIST'
♦Parts included in 135952 O-Ring and Seal Kit
9
Ref. No. Item No.
Description
01 0136665
SCREW
02 0135851
WASHER
03 0135951
EXHAUST DEFLECTOR
04 0135853
O-RING
05 0135854
WASHER
06 0135855
CAP SCREW
07 0135856
FLAT WASHER
08 0135857
CAP
* 09 0136627
EXHAUST SEAL
* 10 0136628
O-RING
11 0136630
POPPET SPRING
* 12 0135861
POPPET O-RING
13 0135862
POPPET
* 14 0135863
PISTON STOP O-RING
* 15 0135864
CYLINDER SEAL O-RING
16 0135865
CYLINDER SPACER
* 17 0135866
GASKET
18 0135867
CYLINDER
* 19 0135900
O-RING
* 20 0135868
CYLINDER O-RING
21 0135869
CYLINDER GUIDE
* 22 0135870
O-RING
* 23 0135871
PISTON O-RING
24 0135943
PISTON & DRIVER ASSEMBLY
25 0135872
DRIVER BLADE
* 26 0136621
O-RING
27 0135874
BUMPER
28 0135875
BODY
29 0136664
O-RING
30 0135877
END CAP
31 0135947
WASHER
32 0135948
BELT CLIP
33 0135878
O-RING
34 0135879
TRIGGER VALVE (A)
* 35 0135880
O-RING
* 36 0135881
O-RING
37 0135882
Trigger Valve (B)
* 38 0135883
O-RING
* 39 0135884
O-RING
40 0135885
SPRING
* 41 0135886
O-RING (2)
42 0135887
PLUNGER
43 0135888
TRIGGER VALVE HOUSING
44 0135892
STATIONARY FRONT PLATE
45 0135891
SCREW
* 46 0135893
O-RING
47 0135896
LATCH ASSEMBLY
* 48 0135890
RETURN SEAL
49 0135944
FRONT PLATE ASSEMBLY
50 0136654
PIN
51 0135895
PIN
Ref. No. Item No.
Description
52 0135897
SAFETY FOOT GUIDE
53 0136658
SPRING
54 0135899
SAFETY
55 0136653
PIN
56 0135945
SAFETY ASSEMBLY
57 0136623
STEP PIN (2)
58 0135946
TRIGGER ASSEMBLY
59 0136611
WASHER
60 0135906
BRACKET
61 0135907
PIN
62 0135908
CAP FEEDER
* 63 0135901
O-RING
64 0137911
SPRING
65 0135910
FEED CYLINDER
* 66 0135911
O-RING
67 0135912
FEED PISTON
* 68 0135913
O-RING
69 0135914
SPRING
70 0135915
PISTON STOP
71 0135916
FEED PISTON COVER
72 0135917
RETAINING RING
73 0135918
HOLD DOWN SPRING
74 0135919
MAGAZINE RIGHT
75 0135920
MAGAZINE COVER
76 0135921
MAGAZINE LEFT
77 0135922
SCREW
78 0135923
NUT
79 0135924
SCREW
80 0135925
FEED CHUTE
81 0135926
SCREW
82 0136608
SCREW
83 0135928
MAGAZINE COVER
84 0135929
SCREW
85 0135930
WEAR PLATE
86 0135931
SCREW
87 0135932
PUSHER
88 0135933
NEGATOR SPRING
89 0135949
TRACK
90 0135934
LATCH COVER
91 0135935
PIN
92 0135936
SPRING
93 0135937
LATCH
94 0135938
MAGAZINE
95 0135950
PIN
96 0135939
FEED CHUTE BRACKET
97 0135940
SCREW
98 0135941
WASHER
99 0135942
SCREW
100 0136645
BARB FITTING (2)
101 0135904
TUBING
www.stingerworld.com
CS58 Cap Stapler
MAINTANANCE'&'STORAGE'
10
MAINTENANCE
1. Disconnect the air hose from the tool when performing inspections, maintenance or repairs.
2. Use air line lubricators. If lubricators are not available, or if hose lengths exceed 10 feet, add
2 drops of non-detergent 20-weight oil daily into the air inlet of the tool.
3. Whenever repairs or replacement of parts inside the body occur, check the piston “O”ring for
adequate grease lubrication.
4. Never use any parts other than genuine STINGER replacement parts.
5. Periodically clean the magazine and nose of the tool with a mild solvent.
STORAGE
1. Disconnect the air hose when storing the tool.
2. Never store the tool in cold weather environments for any duration of time as any frost or ice
formation in the tool will cause tool failures.
3. For prolonged storage, add 2 drops of oil to the air inlet of the tool prior to discontinuing use.
Also clean the exterior of the tool with a mild solvent.
www.stingerworld.com
CS58 Cap Stapler
WARRANTY'
WARRANTY'ITEMS'
'
E8 L+--+'0)%6&-%*+3%+##$2:(4$#,%*+#<'.#%+'1%7&/#4'.%*+#<'.#%4#%&'$%)$+-8%
M8 L+--+'0)%6&-%:/23$-#,%“N”%-4'.#,%1-4D$-%:(+1$#%+'1%34#0&'%-4'.#%4#%'&0%+33(4*+:($%+#%07$)%+-$%'&-2+(%
5$+-4'.%3+-0#%57&#$%(46$%4#%1$3$'1+'0%&'%+33(4*+<&'8%
O8 L+--+'0)%6&-%+((%&07$-%3+-0#%4#%>F%1+)#8%
WARRANTY'CONDITIONS'
%
E8 C7$%:$.4''4'.%1+0$%4'%574*7%07$%5+--+'0)%4#%4'%6&-*$%4#%07$%1+0$%&6%3/-*7+#$8%
M8 C7$%5+--+'0)%4#%'&0%0-+'#6$-+:($8%
O8 C7$%5+--+'0)%4#%D&41$1%:)%+')%&6%07$%6&((&54'.P%
+8 Q:/#$,%24#/#$,%&-%1+2+.$%0&%07$%0&&(%
:8 "#$%&6%3+-0#%&07$-%07+'%.$'/4'$%ACBRSTU%3+-0#%
*8 "#$%&6%6+#0$'$-#%'&0%1$#4.'+0$1%6&-%/#$%4'%07$%0&&(%
18 V&14H*+<&'#%0&%07$%0&&(%07+0%+(0$-%07$%&-4.4'+(%6/'*<&'%&-%4'0$'0%&6%/#$%&6%07$%0&&(%:)%+')&'$%
&07$-%07+'%R+<&'+(%R+4(%
W8 R+<&'+(%R+4(%-$0+4'#%07$%-4.70%0&%-$3(+*$%&-%-$3+4-%+')%5+--+'0)%40$2#%40%1$$2#%'$*$##+-)8%
11
www.stingerworld.com
CS58 Cap Stapler
TROUBLESHOOTING'
PROBLEM:'
E8 C&&(%&3$-+0$#,%:/0%'&%6+#0$'$-#%+-$%
1-4D$'8%
M8 X+3%($+K#%+4-8%
O8 Y+#0$'$-#%Z+2%4'%'&#$%&6%0&&(8%
W8 L$+K%1-4D$%
?8 AK4334'.%6+#0$'$-#%
[8 Y+#0$'$-#%54((%'&0%1-4D$%*&23($0$()%
4'0&%5&-K%34$*$8%
CORRECTION:'
'
! X7$*K%2+.+\4'$%6&-%3-&3$-%6+#0$'$-#8%%
Y+#0$'$-#%#7&/(1%#(41$%6-$$()%4'%+'1%&/0%&6%07$%
2+.+\4'$8%
%
%
! C4.70$'%*+3%#*-$5#8%
%
%
! U$2&D$%6+#0$'$-#%6-&2%2+.+\4'$8%
! N3$'%]/4*K^X($+-_%'&#$%`46%+33(4*+:($a,%-$2&D$%
Z+22$1%6+#0$'$-%+'1%*(&#$%(+0*78%
! b&+1%0&&(8%
%
! X7$*K%0&%2+K$%#/-$%07$-$%4#%+1$J/+0$%+4-%
#/33()8%
%
%
! U$3(+*$%:/23$-%46%5&-'8%%%
! "#$%&'()%-$*&22$'1$1%6+#0$'$-%#4\$#8%%%
! U$3(+*$%2+.+\4'$%46%5&-'8%
! X7$*K%+4-%#/33()%+#%40%2+)%:$%0&&%(&58%
! B'*-$+#$%+4-%3-$##/-$%`1&%'&0%$=*$$1%EMF%@ABa8%
Please contact Inside Sales for technical support if you have any other problems: 800-746-5659
12
Disconnect the air hose from the tool when performing inspections, maintenance or repairs.
2964 Clydon SW, Grand Rapids MI 49519, USA
Phone: 800-968-6245 Fax: 616-531-5970
Contact Inside Sales at
800-746-5659
to place an order for
replacement parts.
Visit our website at
www.stingerworld.com
to learn more about our products
and services.
www.nationalnail.com
www.stingerworld.com
REV 06/15
Table of contents
