Stockmaster Mezzalift User manual

CL/INST06
Assembly
Instructions
BEFORE USE:
see
User Instruction Manual
Defect as a result of incorrect
assembly will not be covered
under your product
warranty.
www.stockmastereurope.nl

1
www.stockmastereurope.nl
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - On a level surface butt the two Mast sections together. (See illustration No. 1)
Step 2 - Fix the Large Mast Joining Plate to the two Mast sections using four of the M6 x 16 button head screws -
Finger tight only. (See illustration No. 2)
Step 3 - Turn the Mast over. Locate the Small Mast Joining Plates and position them inside the Mast channel and
fasten using four of the M6 x 16 button head screws. Ensure Mast sections are correctly aligned and then tighten all
screws.
(See illustration No. 3)
Step 4 - Lift the Mast as shown cut and remove the Wire Tie then lay the Mast flat on its back again. (See illustration
No. 4)
Step 5 -In the centre of the Mast Channel. Cut and remove the Black Wire Ties holding the chain bundle in position.
(See illustration No. 5)
Note: Do NOT cut the White Wire Tie.
Step 6 -Using the White Wire Tie. Pull the stored chain down the length of the mast untill taught. (See illustration
No. 6)
Step 7 - Loosen the Mast Roller at the base of the Mast (See illustration No. 7)
Step 8 - Using the 2 Black Wire Ties supplied. Tie the chain to the top of the Mast thru the holes A & B. Ensure the
White Wire Tie is located between these two tie positions. (See illustration No. 8)
Mast Assembly

2
www.stockmastereurope.nl
Illustration 1 Illustration 2
Illustration 3 Illustration 4
M6 x 16
M6 x 16
Mast Assembly

3
www.stockmastereurope.nl
Illustration 5 Illustration 6
Illustration 7 Illustration 8
A B
Mast Assembly

4
www.stockmastereurope.nl
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - On a level surface lay the mast face-down as shown. (See illustration No. 1)
Step 2 - Remove the Nut from the Winch Shaft at A. Pull out the winch shaft and remove the Sproket. Carefully put
the Sproket, Shaft, Nut & Washer aside. Parts to be re-assembled in Step 4. (See illustration No. 2)
Step 3 - Place the Winch Body inside the opening on the back of the Mast. Insert the Winch Body at 45 degrees so
the Chain fits inside the Winch Body.(See illustration No. 3)
Step 4 - Fix the Winch Mounting Bracket to the Mast at B & C using two of the M6 x 16 button head screws and nyloc
nuts.
Finger tight only. (See illustration No. 4)
Step 5 - Adjust the Winch Mounting Bracket so you can slide the Sprocket back into place. Insert the Winch Shaft
at D and re fit the washer and nut. Fix the Winch Mounting Bracket to the Mast at Eusing an M6 x 16 button head screw
and nyloc nut. Tighten the Winch Shaft and nut firmly then tighten the Winch Mounting Bracket screws and nuts at B, C,
& E (See illustration No. 5)
Illustration 1 Illustration 2
A
Winch Assembly

5
www.stockmastereurope.nl
Winch Assembly
Illustration 3 Illustration 4
Illustration 5
B
C
M6 x 16
E
DM6 x 16

6
www.stockmastereurope.nl
Mounting Bracket Assembly
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Fit the upper Floor Support Angle to the Mast at A & B as shown using two of the M8 x 20 button head
screws and nyloc nuts. Screws facing up. Nuts on top. (See illustration No. 1)
Note: Upper Floor Support Angle can be fitted upside down on the Mast if required for additional height adjustment.
Step 2 - Fit the Mast Cradle Bracket to the bottom of the Mast at C using an M6 x 16 button head screw and nyloc
nut. (See illustration No. 2)
Step 3 - Fix the two Upright Sections to the Base Bracket using four of the M8 x 20 button head screws and nyloc
nuts.
Finger tighten only . (See illustration No. 3)
Step 4- Measure the Vertical Height from the Lower Floor level to the Uppr floor level at the position the Mezz-a-lift
is to be intsalled. (See illustration No. 4)
Step 5 - Position the Base Assembly over the Mast Cradel Bracket. Measure the total length from the upper Floor
Support Angle to the bottom of the Base Assembly. Adjust the position of the base assembly to reflect the measurement
from Step 4. (See illustration No. 5)
Step 6 -Fix the Base Assembly to the Mast Cradel Bracket, thru the fixing slots on both sides of the Upright
Sections using four of the M8 x 20 button head screws and nyloc nuts.
Finger tighten only. (See illustration No. 6)
Illustration 1 Illustration 2
B
A
M8 x 20
M6 x 16
C

7
www.stockmastereurope.nl
Illustration 3 Illustration 4
Illustration 5 Illustration 6
Mounting Bracket Assembly
M8 x 20
M8 x 20

8
www.stockmastereurope.nl
Instalation
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Stand the Mezz-a-Lift into position placing the upper Floor Support Angle on the upper landing in the
required position. With someone supporting the unit, mark the fixing positions A1 - A3 in the upper landing thru the
Floor Support Angle. Drill and fix at these locations with appropriate fixings.
Fixings not supplied (See illustration No. 1)
Step 2 - Using a Spirit Level, level the Mezz-a-Lift front to rear and side to side (See illustration No. 2)
Step 3 - Mark the fixing positions B1 - B4 in the lower floor thru the Base Bracket. Drill and fix at these locations
with appropriate fixings.
Fixings not supplied (See illustration No. 3)
Step 4 - Tighten ALL fasteners now
90°
Illustration 1 Illustration 2
A1
A3
A2

9
www.stockmastereurope.nl
Tighten
ALL Fasteners
at this point
Instalation
Illustration 3
B3
B4
B1
B2

10
www.stockmastereurope.nl
Chain Setting
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Cut and remove the Black Wire Ties at the top of the Mast. Do not cut the Large White Centre Tie
(See illustration No. 1)
Step 2- Position the Chain around the Sprocket using the Large White Wire Tie. Once the Chain is engaged correctly,
cut and remove the Wire Tie. (See illustration No. 2)
Step 3 - Slide the Chain Roller toward the bottom of the Mast to tension the Chain. Check that the Chain is engaged
with the roller and tighten the screw and nut. (See illustration No. 3)
Illustration 1 Illustration 2

11
www.stockmastereurope.nl
Chain Settting
Illustration 3

12
www.stockmastereurope.nl
Installing the Winch Cover & Handle
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Place the Winch Cover over the Winch. Fix the top of the cover to the C slots of the Mast using the Self
Tapping Screws at A and B. (See illustration No. 1)
Step 2 - Fix the bottom flange of the Winch Cover at C to the Mast with an M6 x 16mm bolt and nyloc nut. Fix the
Winch Handle, Washer and nyloc nut to the Winch shaft and tighten. (See illustration No. 2)
Illustration 1
BA
Illustration 2
C
C

13
www.stockmastereurope.nl
Lift Table Assembly
M10 x 16
Illustration 2
M6 x 25
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Fix the Table Brackets to the Mast Carraige with the M10 x 20mm Patchlok bolts. Leave bolts slightly loose .
(See illustration No. 1)
Note: Table Brackets may be fitted in one of two dierent mounting positions depending on prefered table height
Step 2 - Fix the Lift Table to the Table Brackets using the M6 x 25mm bolts and nyloc nuts. Tighten the nuts and
then tighten the Table Bracket to Mast Carraige bolts. (See illustration No. 2)
Illustration 1

14
www.stockmastereurope.nl
Safety Barrier Fence Assembly & Installation
M6 x 65
Illustration 1 Illustration 2
IMPORTANT: To avoid assembly problems follow these instructions exactly.
Step 1 - Assemble the two Side Safety Barrier fences to the Front Safety Barrier Fence with four M6 x 65 button
head screws and nyloc nuts. (See illustration No. 1)
Step 2 - With the Lift Table wound all the way to the bottom of the Mast, position the Safety Barrier Fence so it clears
the Lift Table on all sides. Mark the fixing positions thru the Bottom Flanges in the Safety Barrier Fence Kickrails. Drill and
fix at these locations with suitable fixings.
These fixings not supplied (See illustration No. 2)
IMPORTANT:Test the unit before use. Place a minimum load of 20kg on the Lift Table and
Raise the Lift Table up approximately half a meter. The Table must not move when the Winch
Handle is released. If the Table moves, DO NOT USE and contact your supplier for instructions.

15
www.stockmastereurope.nl
Risk Assesment / Warranty
This completes the product assembly.
WARRANTY
Thank you for choosing Stockmaster.
Your safety is in good hands
Register your 2 year warranty online at
www.stockmastereurope.nl
USER INSTRUCTIONS
Before use see the User Instruction Manual at
www.stockmastereurope.nl
Use this manual to form part of your
Risk Assesment