Stone & Leigh 67 CHS User manual

-67 CHS Changing Station Instructions
Your Stone & Leigh changing station is designed with your child's safety in
mind. It is certified to meet all safety guidelines established by ASTM
International and the CPSC-Consumer Product Safety Commission.
Thank you for purchasing a Stone & Leigh changing station. If you find that you
are missing a part or if a part is defective in any way, contact your Stanley
Furniture retailer for assistance.
ING!
S OR FATAL INJURY
ITHIN ARM'S REACH.
ION!
S OR FATAL INJURY
ITHIN ARM'S REACH.

Tools Required: (Not included)
Phillips head screwdriver
Assembly Instructions:
1. Assembly Hardware is bagged together and attached to the bottom panel of the Changing Station.
2. Position the dresser in a way that you can access the back of it easily.
3. Carefully position the Changing Station on top of the dresser. Center the Changing Station on the top of the
dresser left to right and so that the front of the back rail of the Changing Station is against the back edge of the
dresser top.
4. Attach the two mending plates to the back of the changing station using the supplied 1/2" wood screws and
tighten securely. Pilot holes are provided in the back rail of the changing station to help locate the mending
plates correctly.
5. Attach the changing station with mending plates to the back of the Stone & Leigh dresser using the two 1" x
1/4" bolts, flat washer & lock washer as shown in section "A' below. Tighten the bolts with the supplied allen
wrench.
6. After properly securing the changing station to the Stone & Leigh dresser carefully position the dresser in the
desired location in your room.
7. NOTE: Failure to properly attach the changing station to the Stone & Leigh dresser could result in serious
injury or death.
**Note:
Your furniture may have different design features than
those shown in drawing.
-67 CHS Changing Station Attachment to Dresser Instructions
Back of Dresser
Back of Changing Station Top of
Section "A"
Page 3
Dresser
(2)Mending Plate-(C)
(4) 1/2" Wood Screws-(A)
Hardware Included:
(2) Bolt 1 1
4x 1 4 “-(B)
(2)Flat Washer 1/4"-(D) (2)Lock Washer 1/4"-(E)
F
(1)Allen Wrench 4mm- (F)
B
DE
C
Section "A"
Mending Plate
Felt pads attached
on bottom.
A
C
B
D
E
F

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
IMPORTANT: REPLACEMENT PARTS MAY BE OBTAINED
FROM ANY OF OUR STANLEY DEALERS!
For additional consumer information, call our Customer Services
Department at 1-[phone] Monday-Friday, 8-5 Eastern.
Stanley Furniture Company
200 N Hamilton St
No. 200
High Point, NC 27260
Page 4
CLEANING:
Mix together a mild solution of gentle dishwashing liquid and water, apply to the
changing station surface using a soft clean cloth lightly dampened in the solution. Rinse
with clear water, using a lightly dampened, soft clean cloth, then dry all surfaces
thoroughly with a dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL
WOOL OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE
FURNITURE.
Periodically check to make certain all screws are fastened securely.
If you are missing a part or need a replacement part, do not use substitute parts. Ask your
dealer for replacement parts or contact Customer Service at [phone].
MAINTENANCE:
Have any baby products that you will need, such as powder, wipes, etc., easily accessible.
These items can be placed in the partitioned section on the right hand side of the Changing
Station.
PRODUCT USE:
Storage Area
for Baby Products
091917
ING!
SOR FATAL INJURY
ITHIN ARM'S REACH.
ION!
SOR FATAL INJURY
ITHINARM'S REACH.